Table of Contents
Advertisement
10 Configuration
Assuming an average electricity production efficiency (including
transportation losses) of 40%, the primary energy factor for
electricity equals 2.5 (=1/0.40). The primary energy factor allows you
to compare 2 different energy sources. In this case, the primary
energy use of the heat pump is compared to the natural gas use of
the gas boiler.
#
Code
N/A
[7‑03]
Compares the primary energy use of the
heat pump with that of the boiler.
Range: 0~6
INFORMATION
▪ The primary energy factor can always be set, but is
only used in case the savings mode is set to
Ecological.
▪ To set electricity price values, do NOT use overview
settings. Set them in the menu structure instead
([7.4.5.1], [7.4.5.2], and [7.4.5.3]). For more information
on how to set the energy prices, see the operation
manual and the user reference guide.
INFORMATION
Solar panels. If solar panels are used, set the electricity
price value very low to promote the use of the heat pump.
Space heating control
The basic required settings in order to configure the space heating of
your system are described in this chapter. The weather-dependent
installer settings define the parameters for the weather-dependent
operation of the unit. When weather-dependent operation is active,
the water temperature is determined automatically depending on the
outdoor temperature. Low outdoor temperatures will result in warmer
water and vice versa. During weather-dependent operation, the user
has the possibility to shift up or down the target water temperature
by a maximum of 10°C.
See the user reference guide and/or operation manual for more
details about this function.
Leaving water temperature: Main zone
#
Code
[A.3.1.1.1]
N/A
LWT setpoint mode:
▪ 0 Fixed: The desired leaving water
temperature is:
▪ NOT weather-dependent (i.e. does
▪ fixed in time (i.e., NOT scheduled)
▪ 1 Weather
leaving water temperature is:
▪ weather-dependent (i.e. depends
▪ fixed in time (i.e., NOT scheduled)
Installer reference guide
60
Description
Description
NOT
depend
on
the
outdoor
ambient temperature)
dep.: The desired
on
the
outdoor
ambient
temperature)
continued >>
#
Code
[A.3.1.1.1]
N/A
<< continuation
▪ 2 Fixed/scheduled: The desired
leaving water temperature is:
▪ NOT
▪ according
▪ 3
leaving water temperature is:
▪ weather-dependent
▪ according
[7.7.1.1]
[1‑00]
Set weather-dependent heating:
T t
[1‑01]
[1‑02]
[1-02]
[1‑03]
[1-03]
▪ T
(main)
▪ T
[7.7.1.1]
[1‑00]
<< continuation
[1‑01]
▪ [1‑00]:
temperature. –40°C~+5°C
[1‑02]
▪ [1‑01]:
[1‑03]
temperature. 10°C~25°C
▪ [1‑02]:
temperature
temperature equals or drops below
the low ambient temperature.
[9‑01]°C~[9‑00]°C
Note: This value should be higher
than [1-03] as for low outdoor
temperatures
required.
▪ [1‑03]:
temperature
temperature equals or rises above
the high ambient temperature.
[9‑01]°C~min(45, [9‑00])°C
Note: This value should be lower
than [1-02] as for high outdoor
temperatures less warm water is
required.
Description
weather-dependent
does NOT depend on the outdoor
ambient temperature)
a
schedule.
scheduled
actions
consists
desired shift actions, either preset
or custom.
Remark: This value can only be
set in leaving water temperature
control.
WD/scheduled:
The
desired
(i.e.,
does
depend on the outdoor ambient
temperature)
a
schedule.
scheduled
actions
consists
desired
leaving
water
temperatures
either
preset
custom
Remark: This value can only be
set in leaving water temperature
control.
[1-00]
[1-01]
: Target leaving water temperature
t
: Outdoor temperature
a
continued >>
Low
outdoor
ambient
High
outdoor
ambient
Desired
leaving
water
when
the
outdoor
warmer
water
Desired
leaving
water
when
the
outdoor
EJHA04AAV3 + NHY2KOMB28+32AA
Daikin Altherma H Hybrid
4P556861-1A – 2019.05
(i.e.,
The
of
The
of
or
T a
is
Advertisement
Table of Contents
