Yaesu FTM-300DE Information For Customers Operating

Information for Customers Operating VHF/UHF Transceivers in the UK
Thank you very much for purchasing the YAESU transceiver.
The transceivers listed in this notice are configured at the factory with the ARS (Automatic Repeater Shift) Frequency
Range, and the Repeater shifts, as shown in the below chart "ARS Configuration B2".
When any of the listed transceivers is operated in a location where the frequency range and repeater shifts in use are
as shown in the chart "ARS Configuration C2"; follow the respective procedure to change the Automatic Repeater
Shift configuration, before using the transceiver for the first time.
ARS Configuration "B2"
Factory Default Setting
ARS Frequency Range: 438.20 MHz - less than 439.45 MHz ( - shift )
Repeater Shifts: 7.6 MHz
Caution:
• By changing the ARS designated bands and repeater shifts according to the procedures below, all saved data, such as
Menu and Memory settings, will be deleted. If you need to change the ARS feature setting after using the radio, make
sure to back up your registered data or make a written note, before applying the setting change.
• The ARS feature setting is NOT changed, even when executing the "Factory Reset" to restore the transceiver to the
factory defaults, as described in the Operating Manuals.
FTM-300DE
1. Turn the transceiver OFF.
2. Connect the supplied microphone SSM-85D to the trans-
ceiver.
3. Press and hold the [ F ( SETUP )] and [ GM ] keys while turn-
ing the transceiver ON.
4. Press the [ Power ] key briefly, then "LOCK" will appear on
the display for one sec.
5. Press [ 8 ] à [ 9 ] à [ 7 ] à [ 7 ] à [ 3 ] à [ 5 ] keys on the SSM-
85D microphone.
6. <TYPE B2> appears in the display.
7. Press the [ Power ] key briefly, then "UN LOCK" will ap-
pear on the display for one sec.
FTM-7250DE
1. Turn the transceiver ON.
2. Press the [ BAND ( SQL )] key to enter the 144 MHz band.
3. Press and hold the [ MHz ( SETUP )] key.
4. Rotate the DIAL knob to select "OPEN MSG 28" and
then press the [ MHz ( SETUP )] key.
5. Rotate the DIAL knob to select "MESSAGE" and then
press the [ V/M ( MW )] key.
6. Enter "AH075M".
1) Rotate the DIAL knob to select "A", then press the [ V/
M ( MW )] key.
2) Repeat the previous step to complete the MESSAGE
"AH075M".
3) Press and hold the [ MHz ( SETUP )] key.
FTM-400XDE
1. Turn the transceiver OFF.
2. Connect the supplied microphone MH-48A6JA to the
transceiver.
3. Press and hold the [ F ( MW )] and [ GM ] keys while turning
the transceiver ON.
4. Press the [ Power ] key briefly, then "LOCK" will appear on
the display for one sec.
5. Press [ 8 ] à [ 3 ] à [ 7 ] à [ 8 ] à [ 3 ] à [ 7 ] keys on the MH-
48A6JA microphone.
6. Press the [ Power ] key briefly, then "UNLOCK" will appear
on the display for one sec.
7. Press and hold the [ DISP ( SETUP )] key.
8. Touch the [ RESET/CLONE ] on the display.
ARS Configuration "C2"
Selectable Setting
ARS Frequency Range: 433.00 MHz - less than 433.40 MHz ( + shift )
434.60 MHz - less than 435.00 MHz ( - shift )
Repeater Shifts: 1.6 MHz
8. Rotate the DIAL knob to se-
lect <TYPE C2> and press
and hold the DIAL knob. The
radio will re-start automatical-
ly. Setting of the ARS feature
to "Configuration C2" is suc-
cessfully completed.
To restore the ARS feature setting to the factory default ( B2 ) ,
perform the same procedures above.
7. Turn the transceiver OFF.
8. Press and hold the [ BAND ( SQL )], [ GM ( AMS )] and
[ MODE ( DG-ID )] keys while turning the transceiver ON.
9. <TYPE B2> appears in the display.
10. Rotate the DIAL knob to select <TYPE C2> and press
the [ GM ( AMS )] key. The transceiver will re-start auto-
matically. Setting of the
ARS feature to "Config-
uration C2" is success-
fully completed.
To restore the ARS feature setting to the factory default ( B2 ) ,
perform the same procedures above.
9. T h e A R S C o n f i g u r a t i o n
name "B2" will appear in the
top right of the display.
10. Press [ F ( MW )] key, then the
message <Confirming FROM
"B2" TO "C2"> will appear on
the display.
11. Touch [ OK? ] . The radio will re-start automatically. Set-
ting of the ARS feature to "Configuration C2" is success-
fully completed.
To restore the ARS feature setting to the factory default ( B2 ) ,
perform the same procedures above.
VERSION
RESET/CLONE
MAIN : x . x x x 0EXP B2
PANEL: x . x x
 FACTORY RESET 〉
 PRESET 〉
 RECALL PRESET 〉
 MEM CH RESET 〉
BACK BACK