Yaesu FT-4XR Operating Manual
  1. Manuals
  2. Brands
  3. Yaesu Manuals
  4. Transceiver
  5. FT-4XR
  6. Operating manual

Yaesu FT-4XR Operating Manual

Vhf/uhf dual band fm transceiver
Hide thumbs Also See for FT-4XR:
Table of Contents

Advertisement

Quick Links

VHF/UHF
DUAL BAND FM TRANSCEIVER
FT-4X
FT-4X
Operating Manual
R
E

Advertisement

Table of Contents
loading

Related Manuals for Yaesu FT-4XR

Summary of Contents for Yaesu FT-4XR

  • Page 1 VHF/UHF DUAL BAND FM TRANSCEIVER FT-4X FT-4X Operating Manual...

  • Page 2: Table Of Contents

    Contents Introduction ........................1 About this manual ......................1 Quick Guide ........................2 Controls & Connections ....................3 Transceiver ........................3 Display ..........................5 The Keypad Functions ....................7 Safety Precautions (Be Sure to Read) ................8 Preparation ........................11 Installing the Antenna ....................

  • Page 3: Introduction

    Introduction Thank you for purchasing this Yaesu product. m FT-4XR/XE is a handheld transceiver for operation in the 144 MHz and 430 MHz Amateur radio bands. m A Bridged Transless (BTL) amplifier provides One Full Watt of Audio, in spite of the transceiver’s small size.

  • Page 4: Quick Guide

    Quick Guide Names and display of Controls PWR/VOL Knob PTT Switch Microphone MONI/T-CALL Switch Function Key  (Frequency up and down) Key [ # BAND ] Key Normal operation (VFO Mode) Operating Frequency VFO-A S Meter / PO Meter ① Turning the Power ON 1.

  • Page 5: Controls & Connections

    Controls & Connections Transceiver ⑧ ① ⑨ ⑩ ② ⑭ ⑪ ③ ⑮ ⑦ ④ ⑫ ⑤ ⑥ ⑬ ⑦ ① Strap attachment ( ② Antenna Jack (SMA) ( PTT Switch ( • Press and hold the PTT switch to transmit, and release it to receive. ③...
  • Page 6 Function Key ( Pressing the Function key activates the “Secondary” key function. ⑥ Press and hold the Function key enters the Set mode. In the Set mode, pressing the Function key defines and saves the setting ⑦ Battery pack ( PWR/VOL Knob •...

  • Page 7: Display

    Display Frequency / Memory Tag / PAGER Set Mode Item VFO-A/B Memory Channel Number Home Channel Display Memory Bank S Meter： Displays the received signal strength PO Meter： Displays the transmit power level Icon Description Priority Memory Channel Memory channel registered as a skip memory Repeater Shift Direction Split Memory (two different frequencies) : Appears when the tone encoder is in use.
  • Page 8 Icon Description Appears when the Dual Receive (DW) function is enabled. Appears when the APO (Automatic Power-Off) function is enabled. Appears when the bell function is enabled. Appears when the lock function is enabled. Appears when the Memory Bank function is enabled. Appears when the VOX (Voice Operated Transmit) function is enabled.

  • Page 9: The Keypad Functions

    The Keypad Functions Primary Function (Press Key) Third Secondary Function Function (Press and Inputting (Press F + Memory Recall Hold for over Memory Tag Key) one second) A c t i v a t e s t h e Deactivates the A c t i v a t e s t h e “Secondary”...

  • Page 10: Safety Precautions (Be Sure To Read)

    Yaesu is not liable for any failures or problems caused by the use or misuse of this product by the purchaser or any third party. Also, Yaesu is not liable for damages caused through the use of this product by the purchaser or any third party, except in cases where ordered to pay damages under the laws.
  • Page 11 Do not disassemble or make any alteration to this product. Do not use any battery charger An injury, electric shock, or failure may which is not specified by Yaesu. result. A fire or failure can result. Keep the terminals of the battery When transmitting, keep the pack clean.
  • Page 12 Do not place this transceiver Improper installation may cause the indirect sunlight or near a heater. FT-4XR/XE to fall or drop, resulting in The case may be deformed or an injury or damage. discolored. Do not place a heavy object on the Do not place this transceiver in a power cord of the AC adapter.

  • Page 13: Preparation

    Preparation Installing the Antenna 1. Rotate the antenna clockwise until it is secured. Do not hold or twist the upper part of the Hold the thick base of the antenna antenna when installing or removing it. To do so may break the conductors inside the antenna. Do not key the transmit without installing the antenna.

  • Page 14: Supplied Accessories And Options

    Supplied Accessories and Options Supplied Accessories • Rechargeable Li-Ion Battery Pack (7.4V, 1,750mAh) SBR-28LI SAD-20 * • AC adapter • Operating Manual (this manual) • Rapid Charger SBH-22 • SBR-28LI Manual • Antenna SRA-15 • Belt Clip SHB-18 If any item is missing, contact the dealer from which the transceiver was purchased.

  • Page 15: Operation

    ● Approximate Operating Time and Remaining Charge Level Indication Approximate operating time for the transceiver with the fully charged lithium- Ion battery pack (SBR-28LI), and the indication of the remaining charge level of the battery is shown in the below table: Frequency band Band in Use Charge Level Indication (Icon)

  • Page 16: Tuning To A Frequency

    Tuning to a Frequency ● Press the [] key or [] key to tune the frequency. By pressing the function key and then press the [] key or [] key, the frequency will change in 1 MHz steps. ● The operating frequency may be entered directly from the keypad by pressing the numbered digits on the keypad in the proper sequence.

  • Page 17: Transmission

    Transmission 1. While pressing and holding the PTT switch, speak into the microphone. TX/BUSY indicator lights red during the TX/BUSY Indicator transmission. If the PTT switch is pressed when a frequency other than the amateur ham radio band is Microphone selected, an alarm tone (beep) will be emitted and “ERROR”...

  • Page 18: Locking Keys And Ptt Switch

    Locking Keys and PTT switch 1. Press and hold the [6] key, “LOCK” is displayed on the LCD for one second, the “ ” icon appears on the LCD, and then the keys are locked. • The keys and the PTT switch may be selected to be locked using Set Mode [18 LOCK]( 27).

  • Page 19: Repeater Operation

    MONI/T-CALL switch, and use the PTT switch to activate the transmitter thereafter. If needed, the FT-4XR (USA/Asian version), may be set to access repeaters which require a 1750 Hz burst tone by setting the MONI/T-CALL switch to serve as a “Tone Call” switch instead. To change the configuration of the...

  • Page 20: Using The Memory

    Using the Memory The FT-4XR/XE transceiver incorporates Large-capacity memory channels that can register the operating frequency, communication mode, and other operational information. • 200 Memory Channels • 3 Home Channels • 10 pairs PMS Memory channel Each memory channel can store the following information: •...

  • Page 21: Registering To Memory Channels

    • To recall Memory Channel #200, enter “200”. To recall Programmable Memory channels “L01/U01” through “L10/U10” enter “201/202” through “219/220”. • The FT-4XR/XE may be set to operated only in the registered memory channels. Press and hold the MONI/T.CALL key and the PTT switch simultaneously, while turning the radio ON to enter the preferred operating mode.

  • Page 22: Clearing Memories

    Clearing Memories Press and hold Press the   Press the Function key the Function key → → (Enters the Set mode) (Select Set Mode "20 MEM DEL") (Confirms the setting) 1. Press the [] key or [] key to select the memory channel from which the data is to be cleared.

  • Page 23: Memory Channel Scanning

    Memory Channel Scanning The receiver may be set to scan memory channels: 1. While operating in the VFO mode, press the [ V/M] key to enter the Memory mode. 2. Press and hold the [▲] key or [▼] key. Scanning starts of the memory channels begins. If the scanner halts on an incoming signal, the back light will turn ON and the decimal point between the “MHz”...

  • Page 24: Split Memory

    For additional details on the following functions, refer to the Advanced Manual which may be downloaded from the Yaesu website. Split Memory Two different frequencies, one for receive and another for transmit, may be stored in one memory channel. Using Memory Tag Memory name tags may be assigned to the memory channels and home channels.

  • Page 25: Programmed Vfo Scan

    Programmed VFO Scan The scan condition may be selected for VFO scanning. 1. Press the [ V/M] key to enter the VFO mode. 2. Press and hold the [#BAND] key. 3. Press the [▲] or [▼] key to select the bandwidth for Programmed VFO scanning.

  • Page 26: Weather Alert Scan (In The Usa)

    NOAA Alert Tone while operating using VFO scan or Memory channel scan. When the Weather Alert Scan feature is engaged, the FT-4XR/XE will check the Weather Broadcast Channels for activity every five seconds while scanning. If you watch the display carefully, you'll observe the scanner...

  • Page 27: Convenient Functions

    Convenient Functions VOX Operation The VOX system provides automatic transmit/receive switching based on voice input. With the VOX system enabled, you do not need to press the PTT switch in order to transmit. Optional VOX earpiece microphone (SSM-512B) is also available. VFO Split Mode Two different frequencies, one for receive and another for transmit, may be operated.

  • Page 28: Using Set Mode

    • On some setting screens, key operation is different than described in the above steps (For example, inputting the characters, etc.). Refer to the Advance manual. For additional details, refer to the Advanced Manual which may be downloaded from the Yaesu website Tables of Set Mode Operations Selectable options Set Mode...
  • Page 29 Selectable options Set Mode Description (Options in bold are the item default settings) ID= ------ (6 characters) CW WRT Sets the CW ID during ARTS operation. default: blank DC VLT Displays the voltage. (Voltage) 104 DCS CODEs / OFF 10 DCS.COD Sets the DCS CODE RX and TX. default: 023 R / 023 T 50MS / 250MS / 450MS / Sets the DTMF code transmission delay...
  • Page 30 Selectable options Set Mode Description (Options in bold are the item default settings) OFF / S-1 / S-2 / S-3 / S-4 RF SQL Adjusts the RF Squelch threshold level. /S-5 / S-6 / S-8 / S-FULL RPT.ARS Turns the ARS function on/off. ARS.ON / ARS.OFF OFF / 0.025MHz −...

  • Page 31: Restoring To Defaults (Reset) / Setting The Preferred Operating Mode

    Restoring to Defaults (Reset) / Setting the Preferred Operating Mode The following reset or preferred operating modes may be selected. 1. Turn the transceiver OFF. 2. Press and hold the MONI/T.CALL key and the PTT switch simultaneously, while turning the transceiver ON.

  • Page 32: Specifications

    Specifications ● General Frequency Range RX: 136 - 174 MHz, 400 - 480 MHz TX: 136 - 174 MHz (Asian version) 144 - 146 MHz (European version) 144 - 148 MHz (USA version) 400 - 480 MHz (Asian version) 430 - 440 MHz (European version) 430 - 450 MHz (USA version) FM Broadcast: 65 - 108 MHz Channel Steps...
  • Page 33 ● Receiver Circuit Type : Direct-conversion Sensitivity : 0.2 μV for 12 dB SINAD (140 - 150 MHz, NFM) 0.2 μV for 12 dB SINAD (420 - 470 MHz, NFM) Selectivity (-6 dB/-60 dB) : FM, NFM ±25 kHz / 12.5 kHz AF Output : 800 mW (16 Ω...
  • Page 34 Limited Warranty is valid only in the country/region where this product was originally purchased. On-line Warranty Registration: Thank you for buying YAESU products! We are confident your new radio will serve your needs for many years! Please register your product at www.yae- su.com - Owner’s Corner...
  • Page 35 3. Upon receipt of this product, returned in accordance with the procedures described above, by the YAESU Authorized Service Center, all reasonable efforts will be expended by YAESU MUSEN to cause this product to con- form to its original specifications. YAESU MUSEN will return the repaired product ( or a replacement product ) free of charge to the original purchaser.
  • Page 36 1. Changes or modifications to this device that are not expressly approved by YAESU MUSEN could void the user’s authorization to operate this device. 2. This device complies with part 15 of the FCC Rules. Operation is subject to the...
  • Page 37 Note...
  • Page 38 Note...
  • Page 39 EU Declaration of Conformity We, Yaesu Musen Co. Ltd of Tokyo, Japan, hereby declare that this radio equipment FT-4XE is in full compliance with EU Radio Equipment Directive 2014/53/EU. The full text of the Declaration of Conformity for this product is available to view at http://www.yaesu.com/jp/red...
  • Page 40 Copyright 2018 YAESU MUSEN CO., LTD. All rights reserved. No portion of this manual may be reproduced without the permission of YAESU MUSEN CO., LTD. YAESU MUSEN CO., LTD. Tennozu Parkside Building 2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan YAESU USA 1804L-AC-1 6125 Phyllis Drive, Cypress, CA 90630, U.S.A.

This manual is also suitable for:

Ft-4xe

Table of Contents