Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Gefen DVIRS232-CAT5
Summary of Contents for Gefen DVIRS232-CAT5
- Page 1 DVI RS-232 Extender U S E R M A N U A L www.gefen.com...
- Page 2 Chatsworth, CA 91311 support@gefen.com www.gefen.com Gefen Inc. reserves the right to make changes in the hard ware, packaging and any accompanying doc u men ta tion without prior written notice. The DVI RS-232 Extender is a trademark of Gefen Inc.
-
Page 3: Table Of Contents
Introduction Operation Notes DVI RS-232 Extender Sender Front Panel Descriptions DVI RS-232 Extender Receiver Front Panel Descriptions How To Connect The DVI RS-232 Extender Dip Switch Usage Guide CAT5 Link Cable - Wiring Diagram Specifi cations Warranty TABLE OF CONTENTS... -
Page 4: Introduction
INTRODUCTION The DVI RS-232 Extender sender unit sits next to your computer, DVD player or any set-top box with a DVI output. The cable supplied with the DVI RS-232 Extender connects your DVI source to the send unit. The DVI RS-232 Extender receiver unit sits next to your DVI display - up to 150 feet away. -
Page 5: Operation Notes
* If using a ADC-DVI Adapter, the "5V to cable" jumper by the input connector on the sender unit needs to be enabled. • If the source requires EDID present, you can use the Gefen DVI Detective to provide EDID information. -
Page 6: Dvi Rs-232 Extender Sender Front Panel Descriptions
DVI RS-232 EXTENDER SENDER FRONT PANEL DESCRIPTIONS Connects to 5 volt DVI input connects to RS-232 input power supply DVI source CAT-5 carries CAT-5 carries TMDS signals DDC/RS-232 signals... -
Page 7: Dvi Rs-232 Extender Receiver Front Panel Descriptions
DVI RS-232 EXTENDER RECEIVER FRONT PANEL DESCRIPTIONS Connects to Connects to DVI Connects to 5 volt RS-232 Device display power supply CAT-5 carries CAT-5 carries DDC/RS-232 signals TMDS signals... -
Page 8: How To Connect The Dvi Rs-232 Extender
HOW TO CONNECT THE DVI RS-232 Extender Connect your display to the DVI RS-232 Extender receiver unit. Connect your RS-232 Device to the DVI RS-232 Extender receiver unit. Connect your video source to the DVI RS-232 Extender sender unit Connect your RS-232 source to the DVI RS-232 Extender sender unit Connect your CAT-5 cables between the sender and the receiver Plug the 5V power supplies into the DVI RS-232 Extender sender and receiver units You should now have picture. -
Page 9: Dip Switch Usage Guide
DIP SWITCH USAGE GUIDE Gefen CAT5 Extenders (sender and receiver) both contain a pair of dip switches located on the board. These dip switches are used to select from a set of confi gurations that will equalize the signal to best match the conditions in your setup. -
Page 10: Cat5 Link Cable - Wiring Diagram
CAT5 LINK CABLE - WIRING DIAGRAM... -
Page 11: Specifi Cations
SPECIFICATIONS Video Amplifi er Bandwidth ... 1.65 GHz Single Link Range ... 1920 x 1200 Vertical Frequency Range ... 60 Hz Input Video Signal...1.2 volts p-p Input DDC Signal... 5 volts p-p DVI Input/Output Connector Type ... DVI-I Serial In ...9-Pin Female Serial Out ...9-Pin Male Link Connector ... -
Page 12: Warranty
Gefen Inc. warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen Inc. is notifi ed within two (2) year from the date of shipment, Gefen Inc. will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifi... - Page 13 What kind of CAT-5e cable should I be using? Solid core CAT-5e cable rated at 350 Mhz and terminated in 568a or 568b is the minimum requirement. For resolutions greater than 1280x1024 or 1080i, Gefen recommends solid CAT-6 cables. I’m getting no video on the screens, what can I check? First thing to check is make sure that the video CAT5 is linked to the other video CAT5 port and the same with the DDC ports.
Need help?
Do you have a question about the DVIRS232-CAT5 and is the answer not in the manual?
Questions and answers