Table of Contents
Advertisement
[DETAILED INFORMATION]
*1 The temperature status is indicated with text color (green/yellow/red) and bar scale. Use the projector within the range that the indication is
green.
*2 This is displayed only when the standard DC motor unit installed in the Zoom Lens (Model No.: ET-D75LE6, ET-D75LE8, ET-D75LE10,
ET-D75LE20, ET-D75LE30, ET-D75LE40, etc.) is replaced with the stepping motor unit using the Stepping Motor Kit (Model No.:
ET-D75MKS10), or when a projection lens with the stepping motor is attached.
*3 In the following cases, the recommended time to replace the filter is not set, and it is not displayed.
When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [NORMAL], [USER1], [USER2], or
[USER3], and the [PROJECTOR SETUP] menu → [FILTER SETTING] → [FILTER TYPE] is set to [LONG LIFE].
When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [LONG LIFE1], [LONG LIFE2], or
[LONG LIFE3].
*4 If the runtime of the filter exceeds the recommended time to replace the filter, the runtime is displayed in red.
*5 [CONSOLIDATED RUNTIME] can be obtained with the following calculation formula. Values obtained by the calculation formula contain a
slight error.
A x 2.5 + B x 1.0 + C x 0.5 + D x 0.3 + E x 0.2
f A: Runtime of the light source with [OPERATING MODE] set to [HIGH]
f B: Runtime of the light source with [OPERATING MODE] set to [NORMAL], [USER1], [USER2], or [USER3]
f C: Runtime of the light source with [OPERATING MODE] set to [LONG LIFE1]
f D: Runtime of the light source with [OPERATING MODE] set to [LONG LIFE2]
f E: Runtime of the light source with [OPERATING MODE] set to [LONG LIFE3]
Note
f The content of the status can be sent to the E-mail address (up to two addresses) set in "[E-mail set up] page" (x page 209) when the
<ENTER> button is pressed while displaying the pages 1/6 to 5/6 of the [STATUS] screen.
f The detailed information of the input signal is displayed when the <ENTER> button is pressed while displaying the page 6/6 of the
[STATUS] screen. Information for multiple input signals may be displayed depending on the projected image. Press qw to switch pages.
f There are items that are displayed or not displayed in [SIGNAL INFORMATION] and [DETAILED INFORMATION] depending on the setting
or the input signal.
f If any abnormality has occurred on the projector, press the <DEFAULT> button while the [STATUS] screen is displayed to display the detail
screen of the error information.
f For details on the contents displayed in [SELF TEST], refer to "Self-diagnosis display" (x page 231).
[AC VOLTAGE MONITOR]
Enable or disable the AC voltage monitor function. The value of input supply voltage is displayed on the self-
diagnosis display at the side of the projector when enabled.
1)
Press as to select [AC VOLTAGE MONITOR].
2)
Press qw to switch the item.
f The items will switch each time you press the button.
[OFF]
[ON]
Note
f When [ON] is set, the value of the input supply voltage is always displayed in the self-diagnosis display while the main power of the projector
is turned on.
Chapter 4 Settings — [PROJECTOR SETUP] menu
[INPUT]
[UPPER LEFT INPUT],
[UPPER RIGHT INPUT],
[LOWER LEFT INPUT],
[LOWER RIGHT INPUT]
[SIGNAL FORMAT]
[SIGNAL FREQUENCY]
[SCAN TYPE]
[TOTAL DOTS]
[DISPLAY DOTS]
[TOTAL LINES]
[DISPLAY LINES]
[COLOR FORMAT]
[SAMPLING]
[BIT DEPTH]
[SIGNAL LEVEL]
Conversion formula for [CONSOLIDATED RUNTIME]
Disables the AC voltage monitor function.
Enables the AC voltage monitor function.
Displays the input terminal used for the projected image.
Displays the input terminal corresponding to each screen while in
the four-screen display mode.
Displays the format of the input signal.
Displays the frequency of the input signal.
Displays the scan type of the input signal.
Displays the total dot count of the input signal.
Displays the number of input signal display dots.
Displays the total line count of the input signal.
Displays the number of input signal display lines.
Displays the color format of the input signal.
Displays the sampling information of the input signal.
Displays the gradation of the input signal.
Displays the signal level of the input signal.
ENGLISH - 175
Advertisement
Table of Contents
