Dukane 6770UL User Manual

Hide thumbs

Table Of Contents

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

Table of Contents

Quick Links

Download this manual

Projector

6765WUSS/6770UL/6780WUSS

User's Manual

Please visit our web site for User's Manual in the latest version:

www.dukaneav.com

430-6765WUSS-6770UL-6780WUSS_User Manual rev00

Table of Contents

Troubleshooting

Summary of Contents for Dukane 6770UL

Page 1 Projector 6765WUSS/6770UL/6780WUSS User’s Manual Please visit our web site for User’s Manual in the latest version: www.dukaneav.com 430-6765WUSS-6770UL-6780WUSS_User Manual rev00...
Page 2 • DisplayPort and DisplayPort Compliance Logo are trademarks owned by the Video Electronics Standards Associa- tion. • HDBaseT™ is a trademark of HDBaseT Alliance. • Trademark PJLink is a trademark applied for trademark rights in Japan, the United States of America and other countries and areas. • Blu-ray is a trademark of Blu-ray Disc Association. • CRESTRON and ROOMVIEW are registered trademarks of Crestron Electronics, Inc. in the United States and other countries. • Extron and XTP are registered trademarks of RGB Systems, Inc. in the United States. • Ethernet is either a registered trademark or trademark of Fuji Xerox Co., Ltd. • Other product and company names mentioned in this user’s manual may be the trademarks or registered trademarks of their respective holders. • Virtual Remote Tool uses WinI2C/DDC library, © Nicomsoft Ltd. NOTES (1) The contents of this user’s manual may not be reprinted in part or whole without permission. (2) The contents of this user’s manual are subject to change without notice. (3) Great care has been taken in the preparation of this user’s manual; however, should you notice any questionable points, errors or omissions, please contact us. (4) Notwithstanding article (3), DUKANE will not be responsible for any claims on loss of profit or other matters deemed to result from using the Projector.
Page 3 Important Information Please use the power cord supplied with this projector. If the supplied power cord does not satisfy requirements of your country’s safety standard, and voltage and current for your region, make sure to use the power cord that conforms to and satisfies them. • The power cord you use must be approved by and comply with the safety standards of your country. Please refer to the page 159 about the power cord specification. Rated voltage by country is listed below for your reference. For selecting an appropriate power cord, please check rated voltage for your region by yourself. AC 230 V : European countries AC 120 V : North America Safety Cautions Precautions Please read this manual carefully before using your projector and keep the manual handy for future reference. CAUTION To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. CAUTION TO PREVENT SHOCK, DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit. This symbol alerts the user that important information concerning the operation and maintenance of this unit has been provided. The information should be read carefully to avoid problems. WARNING: TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT USE THIS UNIT’S PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THE PRONGS CAN BE FULLY INSERTED. Machine Noise Information Regulation - 3.
Page 4 Important Information Disposing of your used product In the European Union EU-wide legislation as implemented in each Member State requires that used electrical and electronic prod- ucts carrying the mark (left) must be disposed of separately from normal household waste. This includes projectors and their electrical accessories. When you dispose of such products, please follow the guidance of your local authority and/or ask the shop where you purchased the product. After collecting the used products, they are reused and recycled in a proper way. This effort will help us reduce the wastes as well as the negative impact to the human health and the environment at the minimum level. The mark on the electrical and electronic products only applies to the current European Union Member States. Outside the European Union If you wish to dispose of used electrical and electronic products outside the European union, please contact your local authority and ask for the correct method of disposal. For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in accordance with legislation. According the EU directive 2006/66/EC, the battery can’t be disposed improperly. The battery shall be sepa- rated to collect by local service.
Page 5 Important Information Important Safeguards These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them carefully and heed all warnings. Installation • Do not place the projector in the following conditions: - on an unstable cart, stand, or table. - near water, baths, or damp rooms. - in direct sunlight, near heaters, or heat radiating appliances. - in a dusty, smoky or steamy environment. - on a sheet of paper or cloth, rugs or carpets. • Do not install and store the projector in the below circumstances. Failure to do so may cause of malfunction. - In powerful magnetic fields - In corrosive gas environment - Outdoors • If you wish to have the projector installed on the ceiling: - Do not attempt to install the projector yourself. - The projector must be installed by qualified technicians in order to ensure proper operation and reduce the risk of bodily injury. - In addition, the ceiling must be strong enough to support the projector and the installation must be in accordance with any local building codes. - Please consult your dealer for more information. WARNING •...
Page 6 Important Information Fire and Shock Precautions • Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside your projector. Allow enough space between your projector and a wall. (→ page xi) • Prevent foreign objects such as paper clips and bits of paper from falling into your projector. Do not attempt to retrieve any objects that might fall into your projector. Do not insert any metal objects such as a wire or screwdriver into your projector. If something should fall into your projector, disconnect it immediately and have the object removed by a qualified service personnel. • Do not place any objects on top of the projector. • Do not touch the power plug during a thunderstorm. Doing so may cause electrical shock. • The projector is designed to operate on a power supply of 100-240V AC 50/60 Hz. Ensure that your power supply fits this requirement before attempting to use your projector. • Make sure to mount the power cord stopper before attempting to use your projector. Please refer to page 15 about the power cord stopper. • Do not look into the light source using optical instruments (such as magnifying glasses and mirrors). Visual impair- ment could result. • When turning on the projector, ensure that nobody is facing towards the lens in the path of the light emitted from the laser. Do not look into the lens while the projector is on. Serious damage to your eyes could result. The following label, that is indicated at the lens-mounting-section on the projector cabinet, describes this projector is categorized in the risk group 2 of IEC 62471-5:2015. As with any bright light source, do not stare into the beam, RG2 IEC 62471- 5:2015. • Perform the adjustment from behind or from the side of the projector. Adjusting from the front could expose your eyes to strong light which could injure them.
Page 7 Important Information • Do not let children to operate the projector by themselves. If the projector is operated by children, adults need to attend and keep their eyes on children. • If damage or malfunction of the projector is found, immediately stop to use it and consult your dealer for repair. • Never disassemble, repair, and remodel by end users. If these are performed by end users, it may cause of serious problem on users’ safety. • Consult your dealer for disposing the projector. Never disassemble the projector before disposing it. CAUTION • Do not use the tilt-foot for purposes other than originally intended. Misuses such as gripping the tilt-foot or hang- ing on the wall can cause damage to the projector. • Do not hold the cable cover while moving the projector or do not apply excessive force to the cable cover. Doing so may damage the cable cover, resulting in injury. • Be sure to tighten the screws after attaching the cable cover. Failure to do so may cause the cable cover to come off and fall, resulting in injury or damage to the cable cover. • Do not put bundled cables in the cable cover. Doing so may damage the power cord, resulting in a fire. • Select [HIGH] in Fan mode if you continue to use the projector for consecutive days. (From the menu, select [SETUP] → [OPTIONS(1)] → [FAN MODE] → [MODE] → [HIGH].) • Do not unplug the power cable from the wall outlet or projector when the projector is powered on. Doing so can cause damage to the AC IN terminal of the projector and (or) the prong plug of the power cable. To turn off the AC power supply under the state the projector is ON, use a power strip equipped with a switch and a breaker. • A minimum of two persons are required to carry the projector. Otherwise the projector may tumble or drop, caus- ing personal injury. Caution on Handling the Optional Lens When shipping the projector with the lens, remove the lens before shipping the projector. Always attach the dust cap to the lens whenever it is not mounted on the projector. The lens and the lens shift mechanism may encounter dam- age caused by improper handling during transportation.
Page 8 Important Information • Using the projector at altitudes less than approximately 5500 feet/1700 meters and setting to [HIGH ALTITUDE] can cause the light module to overcool, causing the image to flicker. Switch [FAN MODE] to [AUTO]. • Using the projector at altitudes approximately 5500 feet/1700 meters or higher can shorten the life of optical com- ponents such as the light module. Light Module 1. A light module containing multiple laser diodes is equipped in the product as the light source. 2. These laser diodes are sealed in the light module. No maintenance or service is required for the performance of the light module. 3. End user is not allowed to replace the light module. 4. Contact qualified distributor for light module replacement and further information. Laser Safety Caution • For USA This product is classified as Class 3R of IEC 60825-1 Second edition 2007-03 Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. For other regions This product is classified as Class 1 of IEC 60825-1 Third edition 2014-05 and RG2 of IEC 62471-5 First edition 2015-06. Obey the laws and regulations of your country in relation to the installation and management of the device. • Outline of laser emitted from the built-in light module: • Wave length: 455 nm • Maximum power: 140 W (6765WUSS), 168 W (6780WUSS) •...
Page 9 Important Information Applicable lens unit: NP40ZL/NP41ZL/NP42ZL Horizontal angle (unit: degree) Right Lens position Center Lens unit Zoom Right most (Reference Left most value) Tele 31.7 23.8 31.7 NP40ZL Wide 41.0 31.9 41.0 Tele 12.8 12.8 NP41ZL Wide 27.7 20.6 27.7 Tele NP42ZL Wide 12.9 12.9 Left Vertical angle (unit: degree)
Page 10 Important Information • The caution and the explanatory labels of the LASER PRODUCT in CLASS 3R conforming to IEC 60825-1 Second edition, and in Class 1 conforming to IEC 60825-1 Third edition are stuck on the below indicated positions. For USA Label 1 Label 2 Label 1 Label 2 For other regions Label 1 viii...
Page 11 • Manufacturer’s ID For 6780WUSS For 6765WUSS Note: The Dukane models described in this document are manufactured by NEC and use the same firmware, software programs, control code, and accessory parts. The equivalent Dukane to NEC models are 6765WUSS (NP-PA653UL), and 6780WUSS (NP-PA803UL).
Page 12 Important Information About Copyright of original projected pictures: Please note that using this projector for the purpose of commercial gain or the attraction of public attention in a venue such as a coffee shop or hotel and employing compression or expansion of the screen image with the following func- tions may raise concern about the infringement of copyrights which are protected by copyright law. [ASPECT RATIO], [KEYSTONE], Magnifying feature and other similar features. Turkish RoHS information relevant for Turkish market EEE Yönetmeliğine Uygundur. Health precautions to users viewing 3D images Before viewing, be sure to read health care precautions that may be found in the user’s manual included with your 3D eyeglasses or your 3D compatible content such as Blu-ray Discs, video games, computer’s video files and the like. To avoid any adverse symptoms, heed the following: • Do not use 3D eyeglasses for viewing any material other than 3D images. • Allow a distance of 2 m/7 feet or greater between the screen and a user. Viewing 3D images from too close a distance can strain your eyes. •...
Page 13 Important Information Clearance for Installing the Projector Allow ample clearance between the projector and its surroundings as shown below. The high temperature exhaust coming out of the device may be sucked into the device again. Required clearance is same whenever the projector is installed in any angle. Avoid installing the projector in a place where air movement from the HVAC is directed at the projector. Heated air from the HVAC can be taken in by the projector’s intake vent. If this happens, the temperature inside the projector will rise too high causing the over-temperature protector to automatically turn off the projectors power. 20 cm/7 .9" or greater 13 cm/5.1" or greater Intake vent Exhaust vent NOTE: • The drawing shows the proper clearance required for the left and right of the projector assuming sufficient clearance has been kept for the front, back and top of the projector. • Please consider sufficient clearance to the projector rear side for setting the cable cover. • For the portrait projection, each required clearance between the floor and the intake or the exhaust vent is same with the clearance on the upper illustration. See page 148 for an installation example on portrait projection.
Page 14: Table Of Contents
Table of Contents Important Information .................... i 1. Introduction ......................1 ❶ What’s in the Box? ......................1 ❷ Introduction to the Projector ....................2 General ........................2 Light source · Brightness ..................2 Installation .........................2 Videos ........................2 Network ........................3 Energy-saving ......................3 About this user’s manual ...................4 ❸ Part Names of the Projector ...................5 Front/Top ........................5 Rear ..........................6 Mounting the cable cover ..................7 Controls/Indicator Panel ....................8...
Page 15 Table of Contents ❻ Changing LIGHT MODE/Checking Energy-Saving Effect Using LIGHT MODE [LIGHT MODE]......................33 Checking Energy-Saving Effect [CARBON METER] ..........35 ❼ Correcting Horizontal and Vertical Keystone Distortion [CORNERSTONE] ....36 ❽ Operation for the On-Screen Menu by a commercially available USB mouse ....38 Menu operation .......................38 Menu position control ....................39 Geometric correction ....................39 ❾ Preventing the Unauthorized Use of the Projector [SECURITY] ........41 ❿ Projecting 3D videos .....................44 Procedure to watch 3D videos using this projector ..........44 When videos cannot be viewed in 3D ..............46 ⓫ Controlling the Projector by Using an HTTP Browser ...........47 ⓬ Storing Changes for Lens Shift, Zoom, and Focus [LENS MEMORY]......54 To store your adjusted values in [REF. LENS MEMORY]: ........55 To call up your adjusted values from [REF. LENS MEMORY]: ........57 4. Multi-Screen Projection ................60 ❶ Things that can be done using multi-screen projection ..........60 Case 1. Using a single projector to project two types of videos [PIP/PICTURE BY PICTURE]......................60...
Page 16 Table of Contents ❼ Menu Descriptions & Functions [SETUP] ..............109 [MENU(1)] ......................109 [MENU(2)] ......................110 [INSTALLATION(1)] ....................111 [INSTALLATION(2)] ....................115 [CONTROL] ......................116 [NETWORK SETTINGS] ..................123 [SOURCE OPTIONS] ...................128 [POWER OPTIONS] .....................130 Returning to Factory Default [RESET] ..............132 ❽ Menu Descriptions & Functions [INFO.] ..............133 [USAGE TIME] ......................133 [SOURCE(1)] ......................134 [SOURCE(2)] ......................134 [SOURCE(3)] ......................134 [SOURCE(4)] ......................135 [WIRED LAN] ......................135 [VERSION(1)] .......................135 [OTHERS] ......................136...
Page 17 Table of Contents ❻ Changing the Background Logo (Virtual Remote Tool) ..........164 ❼ Troubleshooting ......................165 Feature of each indicator ..................165 Indicator Message (Status message) ..............165 Indicator Message (Error message) ..............167 Explanation on the POWER indicator and standby state ........168 Common Problems & Solutions ................170 If there is no picture, or the picture is not displayed correctly........172 ❽ PC Control Codes and Cable Connection ..............173 ABOUT THE ASCII CONTROL COMMAND ............174 ❾ Troubleshooting Check List ..................176 ❿ REGISTER YOUR PROJECTOR! (for residents in the United States, Canada, and Mexico) .........................178...
Page 18: Introduction
1. Introduction ❶ What’s in the Box? Make sure your box contains everything listed. If any pieces are missing, contact your dealer. Please save the original box and packing materials if you ever need to ship your projector. Projector Dust cap for lens (24F54091) Remote control AA alkaline batteries Input selection char- * The projector is shipped without (7N901081) (x2) acter sticker a lens. For the types of lens and throw distances, see page 152.
Page 19: ❷ Introduction To The Projector
1. Introduction ❷ Introduction to the Projector This section introduces you to your new projector and describes the features and controls. General • Liquid crystal type high brightness/high resolution projector Model Brightness Resolution Aspect Ratio 6780WUSS 8000 lm WUXGA (1920 × 1200) 16:10 6765WUSS 6500 lm WUXGA (1920 × 1200) 16:10 Light source · Brightness • A long-life laser diode is equipped in the light module The product can be operated at low cost because the laser light source can be used for a long time without requir- ing replacement or maintenance. • Brightness can be adjusted within a wide range Unlike with ordinary light sources, the brightness can be adjusted from 25 to 100% in 1% increments. • [CONSTANT BRIGHTNESS] mode Brightness normally decreases with use, but by selecting [CONSTANT BRIGHTNESS] mode, sensors inside the projector detect and automatically adjust the output, thereby maintaining constant brightness throughout the life of the light module.
Page 20: Network
1. Introduction • Multi-screen projection using multiple projectors This projetor equips the HDBaseT IN/Ethernet and HDBaseT OUT/Ethernet ports. Multiple projectors in same brightness up to four units can be conneted in a daisy chain by a LAN* cable via these terminals. A high quality picture is achieved by dividing and projecting high resolution videos among the various projectors. Furthermore, the boundaries of the screens are smoothed using an edge blending function. Use a commercially available CAT 5e STP cable or one in a higher specification. • Seamless switch function for smoother screen changes when switching the signal When the input connector is switched, the image displayed before switching is held so that that the new image can be switched to without a break due to absence of a signal. • Supports HDMI 3D format This projector can be used to watch videos in 3D using commercially-available active shutter-type 3D eyewear and 3D emitters that support Xpand 3D. Network • Supports wired LAN Equips the LAN and HDBaseT/Ethernet (RJ-45) ports. Utilizing a wired LAN connected with these ports, it enables to control the projector by a computer. • CRESTRON ROOMVIEW and Extron XTP compatibility The projector supports CRESTRON ROOMVIEW and Extron XTP, allowing multiple devices connected in the network to be managed and controlled from a computer. Moreover, it enables to output and control image via an Extron XTP transmitter connected with the projector.
Page 21: About This User's Manual
1. Introduction About this user’s manual The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to review the user’s manual. This may save you time later on. At the beginning of each section of the manual you’ll find an overview. If the section doesn’t apply, you can skip it.
Page 22: ❸ Part Names Of The Projector
1. Introduction ❸ Part Names of the Projector Front/Top The lens is sold separately. The description below is for when the NP41ZL lens is mounted. Indicator Section Remote Sensor (→ page 8) (→ page 12) Remote Sensor (located on the front and the rear) (→ page 12) Exhaust vent Heated air is exhausted from here. Adjustable Tilt Foot (→...
Page 23: Rear
1. Introduction Rear Remote Sensor (located on the Terminals front and the rear) (→ page 9) (→ page 12) Intake vent (→ page xi, 148) Cable cover connection (right and left) Screw holes and grooves for the optional cable cover (→...
Page 24: Mounting The Cable Cover
1. Introduction Mounting the cable cover Mounting the cable cover on the projector allows you hide the cables for a tidy appearance. CAUTION • After mounting the cable cover, be sure to fasten using the screws provided. If not, the cable cover could fall and damage the cable cover and possibly resulting in injury. • Do not bundle the power cord and place it under the cable cover. Doing so could lead to fire. • Do not hold the cable cover while moving the projector and do not apply excessive force to the cable cover. Doing so could damage the cable cover, resulting in the projector falling or causing injury. Mounting Preparations: 1. Connect the power cord and cables to the projector (the connection cords are omitted from the diagrams). 2. Prepare a Phillips screwdriver. 1.
Page 25: Controls/Indicator Panel
1. Introduction Controls/Indicator Panel 11 12 (POWER) Button (→ page 16, 28) 2. POWER Indicator (→ page 14, 16, 28, 165, 166, 167) 3. STATUS Indicator (→ page 165, 166, 167) 4. LIGHT Indicator (→ page 165, 166, 167) 5. TEMP. Indicator (→ page 165, 166, 167) 6. INPUT Button (→ page 18) 7. MENU Button (→ page 74) 8. ▲▼◀▶ / Volume Buttons ◀▶ (→ page 27, 74) 9. ENTER Button (→ page 74) 10. EXIT Button (→ page 74) 11. FOCUS Button (→ page 23) 12.
Page 26: Terminals
1. Introduction Terminals 13 10 1. HDMI 1 IN Terminal (Type A) 13. REMOTE Terminal (Stereo Mini) (→ page 142, 143, 145) Use this terminal for wired remote control of the pro- jector using the remote control, RD-465E. Connect 2. HDMI 2 IN Terminal (Type A) the projector and our remote control, RD-465E, (→ page 142, 143, 145) using a commercially available wired remote 3. DisplayPort IN Terminal control cable.
Page 27: ❹ Part Names Of The Remote Control
1. Introduction ❹ Part Names of the Remote Control 29. ▲▼◀▶ Button 9. Edge Blend. Button (→ page 69) (→ page 74) 10. Multi. Button 30. ENTER Button (→ page 107) (→ page 74) 11. Geometric. Button 31. L-CLICK Button* (→ page 36, 101) 32. R-CLICK Button* 12. INPUT Button 33. VOL./FOCUS (+)(−) Button (→ page 18) (→ page 23, 27) 13. PIP Button 34. D-ZOOM/ZOOM (+)(−) Button (→ page 64) (→ page 25, 32) 14. PBP/POP Button 35. SHUTTER Button (→ page 64) (→ page 30) 15. AUTO ADJ. Button 36. LENS SHIFT Button (→ page 27) (→ page 21) 16. 1 (HDMI 1) Button 37. PICTURE Button (→ page 18)
Page 28: Battery Installation
1. Introduction Battery Installation 1. Press the catch and remove 2. Install new ones (AA). En- 3. Slip the cover back over the batteries until the battery cover. sure that you have the bat- it snaps into place. teries’ polarity (+/−) aligned NOTE: Do not mix different types of batteries or new correctly. and old batteries. Remote Control Precautions • Handle the remote control carefully. • If the remote control gets wet, wipe it dry immediately. • Avoid excessive heat and humidity. • Do not short, heat, or take apart batteries. • Do not throw batteries into fire. • If you will not be using the remote control for a long time, remove the batteries. • Ensure that you have the batteries’ polarity (+/−) aligned correctly. • Do not use new and old batteries together, or use different types of batteries together. • Dispose of used batteries according to your local regulations.
Page 29: Operating Range For Wireless Remote Control
1. Introduction Operating Range for Wireless Remote Control 40 m/1575 inch 20 m/787 inch Remote sensor on projector cabinet Remote control 40 m/1575 inch 40 m/1575 inch • The infrared signal operates by line-of-sight up to a distance of above meters and within a 60-degree angle of the remote sensor on the projector cabinet. • The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.
Page 30: Projecting An Image (Basic Operation)
2. Projecting an Image (Basic Operation) This section describes how to turn on the projector and to project a picture onto the screen. ❶ Flow of Projecting an Image Step 1 • Connecting your computer / Connecting the power cord (→ page 14) Step 2 • Turning on the projector (→ page 16) Step 3 • Selecting a source (→ page 18) Step 4 • Adjusting the picture size and position (→ page 20) • Correcting keystone distortion [CORNERSTONE] (→ page 36, 101) Step 5 • Adjusting a picture and sound - Optimizing a computer signal automatically (→ page 27) - Turning up or down volume (→...
Page 31: ❷ Connecting Your Computer/Connecting The Power Cord
2. Projecting an Image (Basic Operation) ❷ Connecting Your Computer/Connecting the Power Cord 1. Connect your computer to the projector. This section will show you a basic connection to a computer. For information about other connections, see “6-2 Making Connections” on page 141. Connect the display output terminal (mini D-sub 15 pin) on the computer to the computer video input terminal on the projector with a commercially-available computer cable (with ferrite core) and then turn the knobs of the connectors to secure them.
Page 32: Using The Power Cord Stopper
2. Projecting an Image (Basic Operation) CAUTION: Parts of the projector may become temporarily heated if the projector is turned off with the POWER button or if the AC power supply is disconnected during normal projector operation. Use caution when picking up the projector. Using the power cord stopper To prevent the power cord from accidently removing from the AC IN of the projector, use the power cord stopper. Required tool: Phillips screwdriver 1. Mount the power cord stopper over the power plug that connected to the AC IN terminal. 2. Fasten the screw on the power cord stopper.
Page 33: ❸ Turning On The Projector
2. Projecting an Image (Basic Operation) ❸ Turning on the Projector 1. Remove the lens cap. (POWER) button on the projector cabinet 2. Press the or the POWER ON button on the remote control. WARNING The projector produces a strong light. When turning on the power, make sure no one within projection range is looking at the lens. Sleep state Blinking Power On The POWER indicator lit in green will start to blink in blue. After that, the image will be projected onto the screen. TIP: • When the message “PROJECTOR IS LOCKED! ENTER YOUR PASSWORD.” is displayed, it means that the [SECURITY]...
Page 34: Note On Startup Screen (Menu Language Select Screen)
2. Projecting an Image (Basic Operation) Note on Startup screen (Menu Language Select screen) When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one of the 30 menu languages. To select a menu language, follow these steps: 1. Use the ▲, ▼, ◀ or ▶ button to select one of the 30 languages from the menu. 2. Press the ENTER button to execute the selection. After this has been done, you can proceed to the menu operation. If you want, you can select the menu language later. (→ [LANGUAGE] on page 78 and 109) NOTE: • If the message, [PLEASE SET "DATE AND TIME".] is shown, please set the current date and time. (→ page 120)
Page 35: ❹ Selecting A Source
2. Projecting an Image (Basic Operation) ❹ Selecting a Source Selecting the computer or video source NOTE: Turn on the computer or video source equipment connected to the projector. Detecting the Signal Automatically Press the INPUT button for 1 second or longer. The projector will search for the available input source and display it. The input source will change as follows: HDMI1 → HDMI2 → DisplayPort → COMUPTER → HDBaseT → HDMI1 → … • Press it briefly to display the [INPUT] screen. Press the ▼/▲ buttons to match the target input terminal and then press the ENTER button to switch the input. To delete the menu display in the [INPUT] screen, press the MENU or EXIT button. TIP: If no input signal is present, the input will be skipped. Using the Remote Control Press any one of the 1/HDMI 1, 2/HDMI 2, 3/DisplayPort, 4/Computer, or 5/HDBaseT button.
Page 36 2. Projecting an Image (Basic Operation) Selecting Default Source You can set a source as the default source so that it will be displayed each time the projector is turned on. 1. Press the MENU button. The menu will be displayed. 2. Press the ▶ button to select [SETUP] and press the ▼ button or the ENTER button to select [BASIC]. 3. Press the ▶ button to select [SOURCE OPTIONS] and press the ▼ button or the ENTER button. 4. Press the ▼ button three times to select [DEFAULT INPUT SELECT] and press the ENTER button. The [DEFAULT INPUT SELECT] screen will be displayed. (→ page 128) 5. Select a source as the default source, and press the ENTER button. 6. Press the EXIT button a few times to close the menu. 7. Restart the projector. The source you selected in step 5 will be projected. NOTE: Even when [AUTO] is turned on, the [HDBaseT] will not be automatically selected. To set your network as the default source, select [HDBaseT].
Page 37: ❺ Adjusting The Picture Size And Position
2. Projecting an Image (Basic Operation) ❺ Adjusting the Picture Size and Position Use the lens shift dial, the adjustable tilt foot lever, the zoom and the focus ring to adjust the picture size and position. In this chapter drawings and cables are omitted for clarity. Adjusting the projected image’s vertical and horizontal Adjusting the focus position [Focus] [Lens shift] (→ page 22) (→ page 21) Finely adjusting the size of an image Adjusting the projected image’s inclination [Zoom] [Tilt foot] (→ page 25) (→ page 26)
Page 38: Adjusting The Vertical Position Of A Projected Image (Lens Shift)
2. Projecting an Image (Basic Operation) Adjusting the vertical position of a projected image (Lens shift) CAUTION • Perform the adjustment from behind or from the side of the projector. Adjusting from the front could expose your eyes to strong light which could injure them. • Keep hands away from the lens mounting portion while performing a lens shift. Failure to do so could result in fingers being pinched by the moving lens. 1. Press either SHIFT/HOME POSITION button on the cabinet or LENS SHIFT button on the remote control. The [LENS SHIFT] screen will be displayed. 2. Press the ▼▲◀▶ buttons to move the projected image. • To set back the lens to the home position Press and hold the SHIFT/HOME POSITION button over 2 seconds. The lens mounted on the projector goes back to the home position.
Page 39: Focus
2. Projecting an Image (Basic Operation) TIP: • The diagram below shows the lens shift adjustment range (orientation: desk/front). Width of projected image 50％V Height of projected image 100％V 10％H 10％H 10％V 100％H 20％H 20％H Description of symbols: V indicates vertical (height of the projected image), H indicates horizontal (width of the projected image). Focus Recommend to perform the focus adjustment after leaving the projector under the state the TEST PATTERN has been projected for over 30 minutes. Please refer to page 85 in the User’s Manual about the TEST PATTERN.
Page 40 2. Projecting an Image (Basic Operation) Applicable lens: NP40ZL/NP41ZL 1. Press the FOCUS button on the cabinet. The LENS FOCUS control screen will be displayed on. * Press ◀▶ buttons to adjust focus. In another way, press and hold the CTL button and then press VOL./FOCUS +/− button on the remote control 2. When the cursor is on the CENTER on on-screen menu, press either ◀...
Page 41 2. Projecting an Image (Basic Operation) Applicable lens: NP42ZL 1. Press the FOCUS button on the cabinet. Press ◀▶ buttons to adjust focus. In another way, press and hold the CTL button and then press VOL./FOCUS +/− button on the remote control. * PERIPHERY LENS FOCUS is not available for this lens unit.
Page 42: Zoom
2. Projecting an Image (Basic Operation) Zoom 1. Press ZOOM/L-CALIB. button. The ZOOM adjustment screen will be displayed on. • ◀ or ▶ buttons on the cabinet or the remote control are available to adjust ZOOM while the ZOOM adjustment screen is displayed on. •...
Page 43: Adjusting The Tilt Foot
2. Projecting an Image (Basic Operation) Adjusting the Tilt Foot 1. Turn the left and right tilt foot to adjust. The tilt foot lengthen and shorten when turned. Turn one of the tilt foot to adjust the image so that it is level. • If the projected image is distorted, see “3-7 Correcting Horizontal and Vertical Keystone Distortion [CORNERSTONE]” (→ page 36) and “[GEOMETRIC CORRECTION]”...
Page 44: ❻ Optimizing Computer Signal Automatically
2. Projecting an Image (Basic Operation) ❻ Optimizing Computer Signal Automatically Adjusting the Image Using Auto Adjust When projecting a signal from the computer video input terminal, HDMI 1 IN terminal, HDMI 2 IN terminal, DisplayPort IN terminal, HDBaseT IN/Ethernet port, adjust the picture quality with a single touch of the button if the edges of the screen are cut off or if the projection quality is bad. Press the AUTO ADJ. button to optimize a computer image automatically. This adjustment may be necessary when you connect your computer for the first time. [Poor picture] [Normal picture] NOTE: Some signals may take time to display or may not be displayed correctly. • If the Auto Adjust operation cannot optimize the computer signal, try to adjust [HORIZONTAL], [VERTICAL], [CLOCK], and [PHASE] manually. (→ page 90, 91) ❼ Turning Up or Down Volume Sound level from the AUDIO OUT terminal can be adjusted. Important: • Do not turn up the volume to the maximum level on the external speaker system connected to the AUDIO OUT of the projector. Doing so may produce an unexpected, loud sound at the time of turning on or off the projector, causing damage to your hearing.
Page 45: ❽ Turning Off The Projector
2. Projecting an Image (Basic Operation) ❽ Turning off the Projector To turn off the projector: 1. First, press the (POWER) button on the projector cabinet or the STANDBY button on the remote control. The [POWER OFF / ARE YOU SURE ? / CARBON SAV- INGS- SESSION 0.000[g-CO2]] message will appear. Power On Standby 2. Secondly, press the ENTER button or press the (POWER) or the STANDBY button again.
Page 46: ❾ After Use
2. Projecting an Image (Basic Operation) ❾ After Use Preparation: Make sure that the projector is turned off. 1. Unplug the power cord. Loosen the screw coun- Draw off the power cord terclockwise until it starts stopper. racing. 2. Disconnect any other cables. 3. Mount the lens cap on the lens. 4. Before moving the projector, screw in the tilt foot if they have been lengthened.
Page 47: Convenient Features
3. Convenient Features ❶ Turn off the light of the projector (LENS SHUTTER) Press the SHUTTER button on the remote control. The light source will turn off temporarily. Press again to allow the screen to become illuminated again. • You can set the projection light to gradually fade in or out. ❷ Turning off the Image and Sound The projected video and the output sound from the sound output terminal will disappear momentarily. Press the BLANK button. The projected video will be cut off. Press the MUTE button. The audio will be cut off. Press the AV-MUTE button. The projected video and audio will be cut off. • Press the buttons one more time for the cancelled video and audio to appear again. TIP: • The video will disappear but not the menu display.
Page 48: ❸ Shift The On-Screen Menu Displaying Position
3. Convenient Features ❸ Shift the On-Screen Menu displaying position 1. Press the MENU button. The On-Screen Menu will be displayed on. 2. Move the cursor by the ▶ button to the [SETUP] and then press the ENTER button. The cursor will move to the [MENU(1)]. 3. Move the cursor by the ▶ button to the [MENU(2)]. 4. Move the cursor by the ▼ button to the [MENU POSITION] and then press the ENTER. The On-Screen Menu will go into the MENU POSITION setup screen. 5. Move the cursor either to [HORIZONTAL POSITION] or [VERTICAL POSITION] by pressing ▼...
Page 49: ❹ Freezing A Picture
3. Convenient Features ❹ Freezing a Picture Press the FREEZE button to freeze a picture. Press again to resume motion. NOTE: The image is frozen but the original video is still playing back. ❺ Enlarging a Picture You can enlarge the picture up to four times. NOTE: • Depending on an input signal, the maximum magnification may be less than four times, or the function may be restricted. To do so: 1. Press the D-ZOOM (+) button to magnify the picture. 2. Press the ▲▼◀▶ button. The area of the magnified image will be moved 3. Press the D-ZOOM (−) button.
Page 50: ❻ Changing Light Mode/Checking Energy-Saving Effect Using Light Mode
3. Convenient Features ❻ Changing LIGHT MODE/Checking Energy-Saving Effect Using LIGHT MODE [LIGHT MODE] When either [ECO1] or [ECO2] in [LIGHT MODE] is selected, motion noise of the projector is cut down by lowering brightness of its light source. Icon at the bottom LIGHT MODE Description of the menu NORMAL 100% brightness The screen will be brightly lit. Depending on the installation circumstances, the service life of optical parts may be shorten. ECO1 Brightness will be at about 80%. The cooling fan will also slow down accordingly. Lower power consumption ECO2 Brightness will be at about 60%. The cooling fan will also slow down accordingly. Lower power consumption considerably More eco-friendly setting than NORMAL and ECO1.
Page 51 3. Convenient Features NOTE: • The [LIGHT MODE] can be changed by using the menu. Select [SETUP] → [INSTALLATION(1)] → [LIGHT MODE] → [LIGHT MODE]. • The light module used hours can be checked in [USAGE TIME]. Select [INFO.] → [USAGE TIME]. • After a lapse of 1 minute from when the projector displays a blue, black or logo screen, the projector will automatically lower the brightness to the equivalent level of [ECO2] when [NORMAL] or [ECO1] has been selected for [LIGHT MODE] and it will be automatically back to the previous brightness when it detects input signal. • If the projector is overheated in [NORMAL] or [ECO1] mode, there may be a case the projector automatically lowers the bright- ness as a protective function. This is called “Forced ECO MODE”. When the projector is in the Forced ECO MODE, the picture brightness decreases slightly and the TEMP. indicator lights orange. At the same time the Thermometer symbol [ ] is displayed at the bottom right of the screen. When the ambient temperature is lowered under approx 33°, the Forced ECO MODE is cancelled and the projector goes back into the previously set state.
Page 52: Checking Energy-Saving Effect [Carbon Meter]
3. Convenient Features Checking Energy-Saving Effect [CARBON METER] This feature will show energy-saving effect in terms of CO emission reduction (kg) when the projector’s [LIGHT MODE] is set to either [ECO1], [ECO2], or [LONG LIFE]. This feature is called as [CARBON METER]. There are two messages: [TOTAL CARBON SAVINGS] and [CARBON SAVINGS-SESSION]. The [TOTAL CARBON SAVINGS] message shows the total amount of CO emission reduction from the time of shipment up to now. You can check the information on [USAGE TIME] from [INFO.] of the menu. (→ page 133) The [CARBON SAVINGS-SESSION] message shows the amount of CO emission reduction between the time of changing to LIGHT MODE immediately after the time of power-on and the time of power-off. The [CARBON SAVINGS- SESSION] message will be displayed in the [POWER OFF/ ARE YOU SURE ?] message at the time of power-off. TIP: • The formula shown below is used to calculate the amount of CO emission reduction. Amount of CO emission reduction = (Power consumption in [NORMAL] LIGHT MODE – Power consumption in current setting) × CO conversion factor.* Setting the [LIGHT MODE] to [ECO1], [ECO2], or [LONG LIFE] increases CO emissions savings. * Calculation for amount of CO emission reduction is based on an OECD publication “CO Emissions from Fuel Combustion, 2008 Edition”. • The [TOTAL CARBON SAVINGS] is calculated based on savings recorded in 15 minutes intervals. • This formula will not apply to the power consumption which is not affected by whether [LIGHT MODE] is turned on or off.
Page 53: ❼ Correcting Horizontal And Vertical Keystone Distortion [Cornerstone]
3. Convenient Features ❼ Correcting Horizontal and Vertical Keystone Distortion [CORNERSTONE] Use the [CORNERSTONE] feature to correct keystone (trapezoidal) distortion to make the top or bottom and the left or right side of the screen longer or shorter so that the projected image is rectangular. 1. Project an image so that the screen is smaller than the area of the raster. The drawing shows the upper right corner. Projected image 2. Pick up any one of the corners and align the corner of the image with a corner of the screen. 3. Press the Geometric. button either on the cabinet or the remote control. Display the [GEOMETRIC CORRECTION] screen of the on-screen menu. 4. Move the cursor onto [MODE] by ▼ button and press the ENTER. The mode selection screen will displayed on. 5. Select [CORNERSTONE] and press the ENTER.
Page 54 3. Convenient Features 6. Press the ▼ button to align with the [CORNERSTONE] and then press the ENTER button. The drawing shows the upper left icon ( ) is selected. The screen will switch to the [CORNERSTONE] screen. 7. Use the ▲▼◀▶ button to select one icon (▲) which points in the direction you wish to move the projected image frame. 8. Press the ENTER button. 9. Use the ▲▼◀▶ button to move the projected image frame as shown on the example. 10. P ress the ENTER button. 11. U se the ▲▼◀▶ button to select another icon which points in the direction. On the [CORNERSTONE] screen, select [EXIT] or press the EXIT button on the remote control.
Page 55: ❽ Operation For The On-Screen Menu By A Commercially Available Usb Mouse
3. Convenient Features The confirmation screen is displayed. 12. P ress the ◀ or ▶ button to highlight the [OK] and press the ENTER button. This completes the [CORNERSTONE] correction. • Select [CANCEL] and press the ENTER button to return to the [CORNERSTONE] screen. Selecting [CANCEL] will return to the adjustment screen without saving changes (Step 3). Selecting [RESET] will return to the factory default. Selecting [UNDO] will exit without saving changes. NOTE: • Even when the projector is turned on, the last used correction values are applied. • Carry out either one of the following actions to clear the adjustment value of [CORNERSTONE]. • In Step 11, select [RESET] and then press the ENTER button. • In the state [CORNERSTONE] has been selected for [MODE] in the [GEOMETRIC CORRECTION]: • Press the Geometric. button for 2 or more seconds. • Run [DISPLAY] → [GEOMETRIC CORRECTION] → [RESET] in the on-screen menu. • Using CORNERSTONE correction can cause the image to be slightly blurred because the correction is made electronically. • A commercially available USB mouse is available for CORNERSTONE correction. ❽...
Page 56: Menu Position Control
3. Convenient Features 3. Select [EXIT] displayed at the bottom of the menu by left click for going back to the previous level. If the cursor is on the main menu option, it works for closing the menu. (It works as the same performance with the [EXIT] button on the remote control. Menu position control 1. Click the wheel button to display the on-screen menu indication frame. 2. Left click at the position on the projection screen where you want to shift the on-screen menu. The nearest corner of the on-screen menu indication frame will shift to the clicked position. 3. Click the wheel button to close the menu indication frame. Geometric correction The USB mouse can be used for CORNERSTONE CORRECTION, HORIZONTAL CORNER, VERTICAL CORNER and WARP. In this clause, the CORNERSTONE CORRECTION by an USB mouse is explained as an example. 1. While the adjustment screen of the CORNERSTONE CORRECTION is displayed, right click on the pro- jection screen. The shape of mouse pointer will be changed and the correction will become available.
Page 57 3. Convenient Features 2. Left click at the screen corner. The projection screen corner will move to the mouse clicked position. 3. Repeat the step 2 for correcting all distortion. After completion of distortion correction, right click on the projection screen. The shape of mouse pointer will be changed to normal. 4. Left click [EXIT] on the correction screen to finish.
Page 58: ❾ Preventing The Unauthorized Use Of The Projector [Security]
3. Convenient Features ❾ Preventing the Unauthorized Use of the Projector [SECURITY] A keyword can be set for your projector using the Menu to avoid operation by an unauthorized user. When a keyword is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is entered, the pro- jector cannot project an image. • The [SECURITY] setting cannot be cancelled by using the [RESET] of the menu. To enable the Security function: 1. Press the MENU button. The menu will be displayed. 2. Press the ▶ button twice to select [SETUP] and press the ▼ button or the ENTER button to select [MENU(1)]. 3. Press the ▶ button to select [CONTROL]. 4. Press the ▼ button three times to select [SECURITY] and press the ENTER button. The OFF/ON menu will be displayed. 5. Press the ▼ button to select [ON] and press the ENTER button. The [SECURITY KEYWORD] screen will be displayed. 6. Type in a combination of the four ▲▼◀▶ buttons and press the ENTER button.
Page 59 3. Convenient Features 7. Type in the same combination of ▲▼◀▶ buttons and press the ENTER button. The confirmation screen will be displayed. 8. Select [YES] and press the ENTER button. The SECURITY function has been enabled. To turn on the projector when [SECURITY] is enabled: 1. Press the POWER button. The projector will be turned on and display a message to the effect that the projector is locked. 2. Press the MENU button.
Page 60 3. Convenient Features To disable the SECURITY function: 1. Press the MENU button. The menu will be displayed. 2. Select [SETUP] → [CONTROL] → [SECURITY] and press the ENTER button. The OFF/ON menu will be displayed. 3. Select [OFF] and press the ENTER button. The SECURITY KEYWORD screen will be displayed. 4. Type in your keyword and press the ENTER button. When the correct keyword is entered, the SECURITY function will be disabled. NOTE: If you forget your keyword, contact your dealer. Your dealer will provide you with your keyword in exchange for your request code. Your request code is displayed in the Keyword Confirmation screen. In this example [NB52-YGK8-2VD6-K585-JNE6-EYA8] is a request code.
Page 61: ❿ Projecting 3D Videos
3. Convenient Features ❿ Projecting 3D videos This projector can be used to watch videos in 3D using commercially-available active shutter-type 3D eyewear. In order to synchronize the 3D video and eyewear, a commercially-available 3D emitter needs to be connected to the projector (on the projector side). The 3D eyewear receives information from the 3D emitter and performs opening and closing on the left and right. CAUTION Health precautions Before use, please make sure to read any health precautions that may be stated in the operating manuals enclosed with the 3D eyewear and 3D video software (Blu-ray player, games, computer animation files, etc.). Please take note of the following in order to avoid adverse health effects. • Please do not use the 3D eyewear for purposes other than to watch 3D videos. • Please keep a distance of at least 2 m away from the screen when watching videos. Watching a video too close to the screen will increase eye fatigue. • Please do not watch videos continuously for a long period of time. Please take a 15 minutes’ break after every hour of watching. • Please consult a doctor before watching if you or any of your family members have a history of suffering from seizures caused by light sensitivity. • Please stop watching immediately and take a rest when you feel physically unwell while watching (vomiting, gid- diness, nausea, headaches, sore eyes, blurred vision, cramps and dumbness in the limbs, etc.). Please consult a doctor if the symptoms persist. • Please watch a 3D video directly in front of the screen. If you watch a 3D video obliquely from the sides, this may result in physical and eye fatigue.
Page 62 3. Convenient Features The [3D SETTINGS] screen will be displayed. (2) Press the ▼ button to align the cursor with the [FORMAT] and press the ENTER button. The format screen will be displayed. (3) Select the input signal format using the ▼ button and then press the ENTER button. The 3D settings screen will disappear and the 3D video will be projected.
Page 63: When Videos Cannot Be Viewed In 3D
3. Convenient Features When videos cannot be viewed in 3D Please check the following points when videos cannot be viewed in 3D. Please also read the operating manual attached to the 3D eyewear. Possible reasons Solutions The selected signal does not support 3D output� Please change the video signal input to one that supports 3D� The format for the selected signal is turned to [OFF(2D)]� Please change the format in the on-screen menu to [AUTO] or a format that supports 3D�...
Page 64: ⓫ Controlling The Projector By Using An Http Browser
3. Convenient Features ⓫ Controlling the Projector by Using an HTTP Browser Overview Using the web browser on the computer, the HTTP server screen of the projector can be displayed to operate the projector. Possible operations on the HTTP server screen • Configure the settings required for connecting the projector to the network (wired LAN). (NETWORK SETTINGS) • Configure the email notification. (ALERT MAIL) When the projector is connected to a network (wired LAN), notifications on various errors are sent to the email address that has been set up. • Operate the projector. Operations such power on/off of the projector, input terminal switchover, volume control, picture control, and lens control etc. can be carried out. • Configure the [PJLink PASSWORD], [AMX BEACON], and [CRESTRON] etc.
Page 65 3. Convenient Features Handling of the Address for Operation via a Browser Regarding the actual address that is entered for the address or entered to the URL column when operation of the projector is via a browser, the host name can be used as it is when the host name corresponding to the IP address of the projector has been registered to the domain name server by a network administrator, or the host name cor- responding to the IP address of the projector has been set in the “HOSTS” file of the computer being used. Example 1: W hen the host name of the projector has been set to “pj.nec.co.jp”, access is gained to the network setting by specifying http://pj.nec.co.jp/index.html for the address or the entry column of the URL. Example 2: W hen the IP address of the projector is “192.168.73.1”, access is gained to the network setting by specifying http://192.168.73.1/index.html for the address or the entry column of the URL. PROJECTOR ADJUSTMENT POWER: This controls the power of the projector. ON �� Power is switched on� OFF �� Power is switched off� VOLUME: This controls the volume of the projector.
Page 66 3. Convenient Features PICTURE: Controls the video adjustment of the projector. BRIGHTNESS ▲ �� Increases the brightness adjustment value� BRIGHTNESS ▼ �� Decreases the brightness adjustment value� CONTRAST ▲ �� Increases the contrast adjustment value� CONTRAST ▼ �� Decreases the contrast adjustment value� COLOR ▲ �� Increases the color adjustment value� COLOR ▼...
Page 67 3. Convenient Features NETWORK SETTINGS http://<IP Address of Projector (Basic)>/index.html • SETTINGS WIRED LAN INTERFACE Select [LAN] for connecting LAN by wire thru the LAN port. Select [HDBaseT] for connecting LAN by wire thru the HDBaseT IN/Ethernet port. SETTING Set for wired LAN. PROFILE 1/PROFILE 2 Two settings can be set for wired LAN connection. Select PROFILE 1 or PROFILE 2. DISABLE Turn off wired LAN connection. The POWER indicator that is informing the STANDBY state will start to blink in orange long interval (→ page 165). DHCP ON Automatically assign IP address, subnet mask, and gateway to the projector from your DHCP server. DHCP OFF Set IP address, subnet mask, and gateway to the projector assigned by your network administrator. IP ADDRESS Set your IP address of the network connected to the projector. SUBNET MASK Set your subnet mask number of the network connected to the projector. GATEWAY Set the default gateway of the network connected to the projector. AUTO DNS ON DHCP server will automatically assign IP address of DNS server connected to the projector.
Page 68 3. Convenient Features • NAME PROJECTOR NAME Enter a name for your projector so that your computer can identify the projector. A projector name must be 16 characters or less. TIP: Projector name will not be affected even when [RESET] is done from the menu. HOST NAME Enter the hostname of the network connected to the projector. A host name must be 16 or less. DOMAIN NAME Enter the domain name of the network connected to the projector. A domain name must be 60 characters or less. SAVE Click this button to save your settings to the projector’s memory. • ALERT MAIL ALERT MAIL This option will notify various errors to your computer via e-mail when using wired LAN. Placing a checkmark will turn on the Alert Mail feature. Clearing a checkmark will turn off the Alert Mail feature. Sample of a message to be sent from the projector: Subject: [Projector] Projector Information THE COOLING FAN HAS STOPPED. [INFORMATION] PROJECTOR NAME: xxxxx LIGHT HOURS USED: xxxx[H] SENDER’S ADDRESS Enter sender’s address.
Page 69 3. Convenient Features • NETWORK SERVICE PJLink PASSWORD Set a password for PJLink*. A password must be 32 characters or less. Do not forget your password. However, if you forget your password, consult with your dealer. HTTP PASSWORD Set a password for HTTP server. A password must be 10 characters or less. When a password is set up, you will be prompted for your user name (arbitrary) and password during LOGON. AMX BEACON Turn on or off for detection from AMX Device Discovery when connecting to the network supported by AMX’s NetLinx control system. TIP: When using a device that supports AMX Device Discovery, all AMX NetLinx control system will recognize the device and download the appropriate Device Discovery Module from an AMX server. Placing a checkmark will enable detecting the projector from AMX Device Discovery. Clearing a checkmark will disable detecting the projector from AMX Device Discovery. Extron XTP Set for connecting this projector to the Extron XTP transmitter. Placing a checkmark will enable to connect with the XTP transmitter. Clearing a checkmark will disable to connect with the XTP transmitter. SAVE Click this button to save your settings to the projector’s memory. NOTE: If you forget your password, contact your dealer. Please check 24 digits serial number (XXXX-XXXX-XXXX-XXXX-XXXX-XXXX) displayed on the column for the password. *What is PJLink? PJLink is a standardization of protocol used for controlling projectors of different manufacturers. This standard protocol is established by Japan Business Machine and Information System Industries Association (JBMIA) in 2005. The projector supports all the commands of PJLink Class 1. Setting of PJLink will not be affected even when [RESET] is done from the menu. • CRESTRON ROOMVIEW for managing from the computer. DISABLE Disables ROOMVIEW. ENABLE Enables ROOMVIEW. CRESTRON CONTROL for managing from the controller. DISABLE Disables CRESTRON CONTROL.
Page 70 3. Convenient Features LENS CONTROL • CONTROL FOCUS CENTER Align the focus around the optical axis. PERIPHERY Align the focus for the screen peripheral area. ◀/▶ ZOOM Finely adjusting the size of an image. SHIFT ▼▲◀▶ Adjust the projected image’s vertical and horizontal position. HOME Return the lens shift position to the home position. SHUTTER Turn off the light source temporarily. Turn on the light source. SHUTTER CALIB. Correct the adjustable zoom, focus and les shift range. • LENS MEMORY STORE Store the current adjusted values in memory for each input signal. MOVE Applies the adjusted values of LENS SHIFT, ZOOM, and FOCUS to the current signal. RESET Return the adjusted valued to the last condition. • REF. LENS MEMORY PROFILE1/PROFILE2 Select a stored [PROFILE] number. STORE Store each adjusted value of LENS SHIFT, ZOOM and FOCUS for the selected profile as the common values for every input signal. MOVE Move the lens to the stored values for the selected profile.
Page 71: ⓬ Storing Changes For Lens Shift, Zoom, And Focus [Lens Memory]
3. Convenient Features LOAD BY If input signal is switched, the lens will not shift to the les shift, zoom and focus val- SIGNAL ues for the selected [PROFILE] number. If input signal is switched, the lens will shift to the values for the selected [PROFILE] number. If no adjusted values have been stored to [LENS MEMORY], the lens will apply [REF. LENS MEMORY] adjusted values. Alternatively, if no adjusted values have been stored to [REF. LENS MEMORY], the lens will stay unmoved. FORCED Not turn off the image during les shift. MUTE Turn off the image during les shift. • SHUTTER SETTINGS POWER ON OPEN When the power is turned on, the light source comes on and the picture is projected. SHUTTER CLOSE The light source does not come on when the power is turned on. When the SHUTTER button is pressed, the shutter is released and the light source is turned on. FADE TIME Set how long the light will take to fade in after the SHUTTER button is pressed. The time can be set from 0 to 10 seconds in increments of 1 second. Set how long the light will take to fade out after the SHUTTER button is pressed. The time can be set from 0 to 10 seconds in increments of 1 second. ⓬ Storing Changes for Lens Shift, Zoom, and Focus [LENS MEMORY] This function serves to store the adjusted values when using the LENS SHIFT, ZOOM and FOCUS buttons of the pro- jector. Adjusted values can be applied to the signal you selected. This will eliminate the need to adjust lens shift, focus,...
Page 73: To Store Your Adjusted Values In [Ref. Lens Memory]
3. Convenient Features To store your adjusted values in [REF. LENS MEMORY]: 1. Press the MENU button. The menu will be displayed. 2. Press the ▶ button to select [SETUP] and press the ENTER button. 3. Press the ▶ button to select [INSTALLATION(1)].
Page 74 3. Convenient Features 4. Press the ▼ button to select [REF. LENS MEMORY] and press the ENTER button. The [REF. LENS MEMORY] screen will be displayed. 5. Make sure [PROFILE] is highlighted, then press the ENTER button. The [PROFILE] selection screen appears. 6. Press the ▼/▲ buttons to select the [PROFILE] number, then press the ENTER button. Return to the [REF. LENS MEMORY] settings screen. 7. Select [STORE] and press the ENTER button. The confirmation screen will be displayed. 8. Press the ◀ button to select and [YES] and press the ENTER button. Select a [PROFILE] number and save the adjusted [LENS SHIFT], [ZOOM], and [FOCUS] values to it.
Page 75: To Call Up Your Adjusted Values From [Ref. Lens Memory]
3. Convenient Features 9. Press the MENU button. The menu will be closed. TIP: • To store adjusted values for each input source, use the Lens Memory function. (→ page 97) To call up your adjusted values from [REF. LENS MEMORY]: 1. Press the MENU button. The menu will be displayed. 2. Press the ▶ button to select [SETUP] and press the ENTER button. 3. Press the ▶ button to select [INSTALLATION(1)]. 4. Press the ▼ button to select [REF. LENS MEMORY] and press the ENTER button. The [REF. LENS MEMORY] screen will be displayed.
Page 76 3. Convenient Features 5. Make sure [PROFILE] is highlighted, then press the ENTER button. The [PROFILE] selection screen appears. 6. Press the ▼/▲ buttons to select the [PROFILE] number, then press the ENTER button. Return to the [REF. LENS MEMORY] settings screen. 7. Select [MOVE] and press the ENTER button. The lens will shift based on the adjusted values stored in the selected [PROFILE]. 8. Press the ◀ button to select and [YES] and press the ENTER button. The adjusted values will be applied to the current signal. . 9. Press the MENU button.
Page 77 3. Convenient Features TIP: To call up the stored values from [LENS MEMORY]: 1. From the menu, select [ADJUST] → [LENS MEMORY] → [MOVE] and press the ENTER button. The confirmation screen will be displayed. 2. Press the ◀ button to select and [YES] and press the ENTER button. During projection, if the adjusted values for an input signal have been saved, the lens will shift. If not, the lens will shift according to the adjusted values stored in the selected [REF. LENS MEMORY] [PROFILE] number. To automatically apply the stored values at the time of source selection: 1. From the menu, select [SETUP] → [REF. LENS MEMORY] → [LOAD BY SIGNAL] and press the ENTER button.
Page 78: Multi-Screen Projection
4. Multi-Screen Projection ❶ Things that can be done using multi-screen projection This projector can be used singly or arranged in multiple units for multi-screen projection. We will introduce an example using two projection screens here. Case 1 Using a single projector to project two types of videos at the same time [PIP/PICTURE BY PICTURE] Case 2 Using four projectors to project video with a resolution of 3840 × 2160 pixels [TILING] Case 1. Using a single projector to project two types of videos [PIP/PICTURE BY PICTURE] Connection example and projection image In the case of [PICTURE BY PICTURE] In the case of [PIP] On-screen menu operations Display [DISPLAY] → [PIP/PICTURE BY PICTURE] → [MODE] screen in the on-screen menu and select [PIP] or...
Page 79: Case 2. Using Four Projectors To Project Videos With A Resolution Of 3840 × 2160 Pixels [Tiling]
4. Multi-Screen Projection Case 2. Using four projectors to project videos with a resolution of 3840 × 2160 pixels [TILING] Connection example and projection image On-screen menu operations 1 Four similar videos are displayed when four projectors are projected. Please request the retail store to adjust the projection position of each projector. NOTE: • When setting up the projector, assign a unique control ID to each projector.
Page 80 4. Multi-Screen Projection 2 Operate the on-screen menu using the four respective projectors to divide the image into four portions. Display [DISPLAY] → [MULTI SCREEN] → [PICTURE SETTING] Screen in the on-screen menu and select [TIL- ING]. (1) In the screen for setting the number of horizontal units, select [2 UNITS]. (number of units in the horizontal direction) (2) In the screen for setting the number of vertical units, select [2 UNITS].
Page 81: Things To Note When Installing Projectors
4. Multi-Screen Projection Things to note when installing projectors • Leave sufficient space on the left and right of the projector so that the intake and exhaust vents of the projector are not obstructed. When the intake and exhaust vents are obstructed, the temperature inside the projector will rise and this may result in a malfunction. • Please do not pile up the projectors directly on top of one another when installing them. When the projectors are piled up on top of one another, they may fall down, resulting in damage and failure. The following installation is recommended when combining the installation of two projectors for multi-screen projec- tion. Please leave sufficient space on the left and right of the projector. Cabinet WARNING Please request the retail store for special installation services such as when mounting the projector to the ceiling. Never carry out the installation by yourself. The projector may fall down and result in injury. Please use a sturdy cabinet that can withstand the weight of the projector for the installation. Please do not pile up the projectors directly on top of one another. NOTE: • For the range of the projection distance, please refer to the Appendix “Throw distance and screen size”. (→ page 152)
Page 82: ❷ Displaying Two Pictures At The Same Time
4. Multi-Screen Projection ❷ Displaying Two Pictures at the Same Time The projector has a feature that allows you to view two different signals simultaneously. You have two modes: PIP mode and PICTURE BY PICTURE mode. The projection video in the first screen display is known as the main display while the projection video that is called out subsequently is known as the sub-display. Select the projection function under [DISPLAY] → [PIP/PICTURE BY PICTURE] → [MODE] in the on-screen menu (the default factory setting when shipped is PIP). (→ page 99) • A single screen is projected when power is turned on. Picture in Picture function A small sub-display is displayed inside the main display. Main Display The sub-display can be set up and adjusted as follows. (→ page 99) • Select whether to display the sub-display at the top right, top left, bottom right or bottom left of the screen (the size of the sub-display can be selected and Sub-Display the position can be fine-tuned) • Switch the main display with the sub-display Picture by picture function Display the main display and sub-display side by side.
Page 83: Projecting Two Screens
4. Multi-Screen Projection Projecting two screens 1. Press the MENU button to display the on-screen menu and select [DISPLAY] → [PIP/PICTURE BY PICTURE]. This displays the [PIP/PICTURE BY PICTURE] screen in the on-screen menu. 2. Select [SUB INPUT] using the ▼/▲ buttons, and press the ENTER button. This displays the [SUB INPUT] screen. 3. Select the input signal using the ▼/▲ buttons, and press the ENTER button. * This screen belongs to a HDBaseT model. The [PIP] (PICTURE IN PICTURE) or [PICTURE BY PICTURE] screen set up under [MODE] is projected. (→ page 99) • When the signal name is displayed in grey, this means that it cannot be selected.
Page 84: Switching The Main Display With The Sub-Display And Vice Versa
4. Multi-Screen Projection Switching the main display with the sub-display and vice versa 1. Press the MENU button to display the on-screen menu and select [DISPLAY] → [PIP/PICTURE BY PICTURE]. This displays the [PIP/PICTURE BY PICTURE] screen in the on-screen menu. 2. Select [PICTURE SWAP] using the ▼/▲ buttons and then press the ENTER button. Display the screen for switching the display positions. 3. Select [ON] using the ▼ button and then press the ENTER button. The video of the main display will switch with that of the sub-display. Sub-display video Main display video Main display video...
Page 85: Restrictions
4. Multi-Screen Projection Restrictions • The following operations are enabled only for the main display. • Audio-visual adjustments • Video magnification / compression using the partial D-ZOOM/ZOOM +/− buttons. However, magnification / compression is up to the positions set in [PICTURE BY PICTURE BORDER] only. • TEST PATTERN • The following operations are enabled for both the main display and sub-display. These operations cannot be ap- plied individually. • Momentary deletion of video / audio • Video pause • [PIP/PICTURE BY PICTURE] cannot be used when a 3D video is being displayed. • When using the [PIP/PICTURE BY PICTURE] function, [DYNAMIC CONTRAST] can not be used. • [PIP/PICTURE BY PICTURE] cannot be used when the signal input has a resolution of 1920 × 1200 or more. • The HDBaseT OUT/Ethernet port has a repeater function. The output resolution is limited by the maximum resolu- tion of the connected monitor and projector.
Page 86: ❸ Displaying A Picture Using [Edge Blending]
4. Multi-Screen Projection ❸ Displaying a Picture Using [EDGE BLENDING] A high resolution video can be projected on an even bigger screen by combining multiple projectors on the left, right, top and bottom. This projector is equipped with an “EDGE BLENDING Function” that makes the edges (boundaries) of the projection screen indistinguishable. NOTE: • For projector throw distances, refer to “Throw distance and screen size” on page 152. • Before performing the Edge Blending function, place the projector in the correct position so that the image becomes square in the appropriate size, and then make optical adjustments (lens shift, focus, and zoom). • Adjust the brightness of each projector using [REF. LIGHT ADJUST] under [LIGHT MODE]. In addition, use [REF. WHITE BALANCE] to adjust the [CONTRAST], [BRIGHTNESS] and [UNIFORMITY]. Before explaining use of the Edge Blending function This section explains the case for “Example: Placing two projectors side by side”. As shown, the projected image on the left is referred to as “Projector A” and the projected image on the right is referred to “Projector B”. Unless otherwise specified hereinafter, the “projector” is used to mean both A and B. Example: Placing two projectors side by side Edge Blending area Projected area Projected area Projector A Projector B...
Page 87: Setting The Overlap Of Projection Screens
4. Multi-Screen Projection Preparation: • Turn on the projector and display a signal. • When performing settings or adjustments using one remote control, enable the [CONTROL ID] for assigning ID to each projector so as not to activate the other projectors. (→ page 121) Setting the overlap of projection screens ① Enable [EDGE BLENDING]. 1 Press the “Edge Blend.” button. The [EDGE BLENDING] screen will be displayed. Align the cursor with [MODE] and then press the ENTER but- ton.
Page 88 4. Multi-Screen Projection 4 Select [CONTROL] → [ON] and press the ENTER button. Each [TOP], [BOTTOM], [LEFT], [RIGHT], and [BLACK LEVEL] has its own [CONTROL], [MARKER], [RANGE], and [POSITION]. • For Projector A, set the [CONTROL] for the [TOP], [LEFT] and[BOTTOM] to [OFF]. Similarly for Projector B, set the [CONTROL] for the [TOP], [RIGHT] and [BOTTOM] to [OFF]. ② Adjust [RANGE] and [POSITION] to determine an area of overlapped edges of images projected from each projector. Turning on [MARKER] will display markers in magenta and green. The magenta marker is used for [RANGE] and green one for [POSITION]. [RANGE] (Determine an area of overlapped edges of images.) Turn on [RIGHT] Turn on [LEFT]...
Page 89: [Blend Curve]
4. Multi-Screen Projection 1 Adjust [RANGE]. Use the ◀ or ▶ button to adjust the overlapped area. TIP: • Adjust to overlap one projector’ marker with the other projector’s marker. 2 Adjust [POSITION]. Use the ◀ or ▶ button to align one edge with the other edge of overlapped images. TIP: • When displaying a signal with a different resolution, perform the Edge Blending function from the start. • Setting of [MARKER] will not be saved and return to [OFF] when the projector is turned off.
Page 90: Black Level Adjustment
4. Multi-Screen Projection 2. Select one option among nine by ▲ or ▼. Black Level Adjustment This adjusts the black level of the overlapping area and the non-overlapping area of the multi-screen (EDGE BLENDING). Adjust the brightness level if you feel the difference is too large. NOTE: This function is enabled only when [MODE] is turned on. Adjustable area varies depending on what combination of [TOP], [BOTTOM], [LEFT] and [RIGHT] are turned on. Example: Adjusting the Black Level when placing two projectors side by side Width of overlap Adjust [CENTER] Adjust [CENTER] Projector A’s Projector B’s image image Adjust [CENTER-RIGHT] Adjust [CENTER-LEFT] 1. Select [DISPLAY] → [EDGE BLENDING] → [BLACK LEVEL] and press the ENTER button. The screen will switch to the black level adjustment screen.
Page 91 4. Multi-Screen Projection 2. Use the ▼ or ▲ button to select an item and use the ◀ or ▶ to adjust the black level. Do this for the other projector if necessary. 9-segmented portions for Black Level adjustment The center projector This function adjusts the brightness level of 9-segmented portions for the center projector and 4-segmented portions for the left bottom projector as shown below. TOP-CENTER TOP-LEFT TOP-RIGHT CENTER- LEFT CENTER-RIGHT CENTER BOTTOM-LEFT BOTTOM-RIGHT BOTTOM-CENTER TOP-CENTER TOP-RIGHT CENTER-RIGHT CENTER TIP:...
Page 92: Using On-Screen Menu
5. Using On-Screen Menu ❶ Using the Menus NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected. 1. Press the MENU button on the remote control or the projector cabinet to display the menu. NOTE: The commands such as ENTER, EXIT, ▲▼, ◀▶ in the bottom show available buttons for your operation. 2. Press the ◀▶ buttons on the remote control or the projector cabinet to display the submenu. 3. Press the ENTER button on the remote control or the projector cabinet to highlight the top item or the first tab. 4. Use the ▲▼ buttons on the remote control or the projector cabinet to select the item you want to adjust or set. You can use the ◀▶ buttons on the remote control or the projector cabinet to select the tab you want. 5. Press the ENTER button on the remote control or the projector cabinet to display the submenu window. 6. Adjust the level or turn the selected item on or off by using the ▲▼◀▶ buttons on the remote control or the projector cabinet. Changes are stored until adjusted again. 7. Repeat steps 2-6 to adjust an additional item, or press the EXIT button on the remote control or the projector cabinet to quit the menu display. NOTE: When a menu or message is displayed, several lines of information may be lost, depending on the signal or settings. 8. Press the MENU button to close the menu. To return to the previous menu, press the EXIT button.
Page 93: ❷ Menu Elements
5. Using On-Screen Menu ❷ Menu Elements Slide bar Solid triangle Available buttons Source Menu mode Highlight Radio button LIGHT MODE symbol Off Timer remaining High Altitude symbol time Thermometer symbol Key Lock symbol Menu windows or dialog boxes typically have the following elements: Highlight ��Indicates the selected menu or item� Solid triangle ��Indicates further choices are available�...
Page 94: ❸ List Of Menu Items
5. Using On-Screen Menu ❸ List of Menu Items • Basic menu items are indicated by shaded area. Some menu items are not available depending on the input source. Menu Item Default Options 1:HDMI1 2:HDMI2 3:DisplayPort INPUT 4:COMPUTER 5:HDBaseT ENTRY LIST TEST PATTERN MODE STANDARD STANDARD, PROFESSIONAL AUTO, 1:HIGH-BRIGHT, 2:PRESENTATION, 3:VIDEO, 4:MOVIE, PRESET 5:GRAPHIC, 6:sRGB, 7:DICOM SIM� GENERAL HIGH-BRIGHT, PRESENTATION, VIDEO, MOVIE, GRAPHIC, sRGB, REFERENCE DICOM SIM�...
Page 95 5. Using On-Screen Menu Menu Item Default Options STEREO VIEWER SINGLE SINGLE, DUAL LEFT, DUAL RIGHT STEREO FILTER SINGLE SINGLE, DUAL LEFT, DUAL RIGHT AUTO, OFF(2D), FRAME PACKING, SIDE BY SIDE(HALF), SIDE 3D SETTINGS FORMAT AUTO BY SIDE(FULL), TOP AND BOTTOM, FRAME ALTERNATIVE, LINE ALTERNATIVE ADJUST L/R INVERT...
Page 96 5. Using On-Screen Menu Menu Item Default Options MODE OFF, ON CONTRAST W CONTRAST R CONTRAST G WHITE BALANCE CONTRAST B BRIGHTNESS W BRIGHTNESS R BRIGHTNESS G BRIGHTNESS B MULTI MODE OFF, ZOOM, TILING DISPLAY SCREEN HORIZONTAL ZOOM VERTICAL ZOOM ZOOM HORIZONTAL POSITION...
Page 97 5. Using On-Screen Menu Menu Item Default Options POWER ON SHUTTER OPEN OPEN, CLOSE INSTALLA- SHUTTER SETTINGS FADE IN TIME 0–10 SEC TION(2) FADE OUT TIME 0–10 SEC MENU MODE ADVANCED ADVANCED, BASIC ADMINISTRA- NOT SAVE SETTING VALUES OFF, ON TOR MODE NEW PASSWORD CONFIRM PASSWORD...
Page 98 5. Using On-Screen Menu Menu Item Default Options INTERFACE LAN, HDBaseT PROFILES DISABLE, PROFILE 1, PROFILE 2 DHCP OFF, ON IP ADDRESS WIRED LAN SUBNET MASK GATEWAY AUTO DNS OFF, ON DNS CONFIGURATION RECONNECT PROJECTOR NAME PROJECTOR NAME PJ-******** HOST NAME pj-******** DOMAIN DOMAIN NAME...
Page 99 5. Using On-Screen Menu Menu Item Default Options LIGHT HOURS USED USAGE TIME TOTAL CARBON SAVINGS INPUT TERMINAL RESOLUTION HORIZONTAL FREQUENCY VERTICAL FREQUENCY SOURCE(1) SYNC TYPE SYNC POLARITY SCAN TYPE SOURCE NAME ENTRY NO� SIGNAL TYPE BIT DEPTH SOURCE(2) VIDEO LEVEL SAMPLING FREQUENCY 3D FORMAT INPUT TERMINAL...
Page 100: ❹ Menu Descriptions & Functions [Input]
5. Using On-Screen Menu ❹ Menu Descriptions & Functions [INPUT] 1:HDMI1 This projects the video of the device connected to the HDMI 1 IN terminal. 2:HDMI2 This projects the video of the device connected to the HDMI 2 IN terminal. 3:DisplayPort This projects the video of the device connected to the DisplayPort IN terminal. 4:COMPUTER This projects the video of the device connected to the computer video input terminal. (This projects the analog RGB signal or component signal.) 5:HDBaseT Projecting the HDBaseT signal. ENTRY LIST Displays a list of signals. See the following pages. TEST PATTERN Closes the menu and switches to the test pattern screen.
Page 101 5. Using On-Screen Menu Using the Entry List When any source adjustments are made, the adjustments are automatically registered in the Entry List. The (adjust- ment values of) registered signals can be loaded from the Entry List whenever necessary. However, only up to 100 patterns can be registered in the Entry List. When 100 patterns have been registered in the Entry List, an error message is then displayed and no additional patterns can be registered. You should thus delete (adjustment values of) signals that are no longer needed. Displaying the Entry list 1. Press the MENU button. The menu will be displayed. 2. Press the ◀ or ▶ button to select [INPUT]. The INPUT list will be displayed. * This screen belongs to a HDBaseT model. 3. Use the ◀, ▶, ▲, or ▼ to select [ENTRY LIST] and press the ENTER button.
Page 102 5. Using On-Screen Menu Entering the currently projected signal into the Entry List [ (STORE)] 1. Press the ▲ or ▼ button to select any number. 2. Press the ◀ or ▶ button to select [ (STORE)] and press the ENTER button. Calling up a signal from the Entry List [ (LOAD)] Press the ▲ or ▼ button to select a signal and press the ENTER button. Editing a signal from the Entry List [ (EDIT)] 1. Press the ▲ or ▼ button to select a signal you wish to edit. 2. Press the ◀, ▶, ▲, or ▼ button to select [ (EDIT)] and press the ENTER button. The EDIT window will be displayed. SOURCE NAME Enter a signal name. Up to 18 alphanumeric characters can be used.
Page 103 5. Using On-Screen Menu Cutting a signal from the Entry List [ (CUT)] 1. Press the ▲ or ▼ button to select a signal you wish to delete. 2. Press the ◀, ▶, ▲, or ▼ button to select [ (CUT)] and press the ENTER button. The signal will be deleted from the Entry List and the deleted signal will be displayed on the clipboard at the bot- tom of the Entry List. NOTE: • The currently projected signal cannot be deleted.
Page 104: ❺ Menu Descriptions & Functions [Adjust]
5. Using On-Screen Menu ❺ Menu Descriptions & Functions [ADJUST] [PICTURE] [MODE] This function allows you to determine how to save settings for [DETAIL SETTINGS] of [PRESET] for each input. STANDARD �� Saves settings for each item of [PRESET] (Preset 1 through 7) PROFESSIONAL �� Saves all the settings of [PICTURE] for each input� NOTE: • When [TEST PATTERN] is displayed, [MODE] cannot be selected. [PRESET] This function allows you to select optimized settings for your projected image.
Page 105 5. Using On-Screen Menu [DETAIL SETTINGS] [GENERAL] Storing Your Customized Settings [REFERENCE] This function allows you to store your customized settings in [PRESET 1] to [PRESET 7]. First, select a base preset mode from [REFERENCE], then set [GAMMA CORRECTION] and [COLOR TEMPERA- TURE]. HIGH-BRIGHT �� Recommended for use in a brightly lit room� PRESENTATION �� Recommended for making a presentation using a PowerPoint file� VIDEO �� Recommended for typical TV program viewing� MOVIE �� Recommended for movies� GRAPHIC ��...
Page 106 5. Using On-Screen Menu Adjusting Color Temperature [COLOR TEMPERATURE] This option allows you to select the color temperature of your choice. A value between 5000 K and 10500 K can be set in 100 K units. NOTE: When [HIGH-BRIGHT] is selected in [REFERENCE], this function is not available. Adjusting Brightness and Contrast [DYNAMIC CONTRAST] When set, the most optimal contrast ratio is adjusted according to the video. OFF �� Dynamic contrast is disabled� MOTION IMAGE �� Most optimal settings for moving images� STILL IMAGE �� Most optimal settings for static images� Rapidly follows any changes in the video� NOTE: • Depending on the conditions, projector settings such as [DYNAMIC CONTRAST] may not be able to be selected.
Page 107 5. Using On-Screen Menu [SHARPNESS] Controls the detail of the image. [COLOR] Increases or decreases the color saturation level. [HUE] Varies the color level from +/− green to +/− blue. The red level is used as reference. NOTE: • When [TEST PATTERN] is displayed, [CONTRAST], [BRIGHTNESS], [SHARPNESS], [COLOR] and [HUE] cannot be adjusted. [RESET] The settings and adjustments for [PICTURE] will be returned to the factory default settings with the exception of the following; Preset numbers and [REFERENCE] within the [PRESET] screen. The settings and adjustments under [DETAIL SETTINGS] within the [PRESET] screen that are not currently selected will not be reset.
Page 108: [Image Options]
5. Using On-Screen Menu [IMAGE OPTIONS] Adjusting Clock and Phase [CLOCK/PHASE] This allows you to manually adjust CLOCK and PHASE. CLOCK �� Use this item to fine tune the computer image or to remove any vertical banding that might appear� This function adjusts the clock frequencies that eliminate the horizontal banding in the image� This adjustment may be necessary when you connect your computer for the first time�...
Page 109 5. Using On-Screen Menu Adjusting Horizontal/Vertical Position [HORIZONTAL/VERTICAL] Adjusts the image location horizontally and vertically. • An image can be distorted during the adjustment of [CLOCK] and [PHASE]. This is not malfunction. • The adjustments for [CLOCK], [PHASE], [HORIZONTAL], and [VERTICAL] will be stored in memory for the cur- rent signal. The next time you project the signal with the same resolution, horizontal and vertical frequency, its adjustments will be called up and applied. To delete adjustments stored in memory, from the menu, you select [SETUP] → [RESET] → [CURRENT SIGNAL] and reset the adjustments. [BLANKING] Adjusts the display range (blanking) at the top, bottom, left and right edges of the input signal. Selecting Overscan Percentage [OVERSCAN] Select overscan percentage (Auto, 0%, 5% and 10%) for signal. Projected image Overscaned by 10% NOTE: • The [OVERSCAN] item is not available: - w hen [NATIVE] is selected for [ASPECT RATIO].
Page 110 5. Using On-Screen Menu Selecting the Aspect Ratio [ASPECT RATIO] Use this function to select the screen’s lateral:longitudinal aspect ratio. The projector automatically identifies the signal being input and sets the optimum aspect ratio. For Computer signal For HDTV/SDTV signals Resolution Aspect Ratio 640 × 480 SVGA 800 × 600 1024 × 768 WXGA 1280 × 768 15:9 WXGA 1280 × 800 16:10 HD(FWXGA) 1366 × 768 approx. 16:9 WXGA+ 1440 × 900 16:10 SXGA 1280 × 1024 SXGA+ 1400 × 1050 WXGA++ 1600 × 900 16:9 UXGA 1600 × 1200 WSXGA+ 1680 × 1050 16:10 FHD(1080P) 1920 × 1080...
Page 111 5. Using On-Screen Menu Options Function 15:9 The image is displayed in 15:9 aspect ratio 16:10 The image is displayed in 16:10 aspect ratio NATIVE The projector displays the current image in its true resolution when the incoming computer signal has a lower or higher resolution than the projector’s native resolution. (→ page 2) When the incoming computer signal has a higher resolution than the projector’s native resolution, the center of an image will be displayed. LETTER BOX The image of a letterbox signal (16:9) is stretched equally in the horizontal and vertical directions to fit the screen. WIDE SCREEN The image of a squeeze signal(16:9) is stretched left and right in 16:9. ZOOM The image of a squeeze signal (16:9) is stretched left and right in 4:3. Parts of the displayed image are cropped at the left and right edges and therefore not visible. FULL Project to full screen size. TIP: • Image position can be adjusted vertically using [POSITION] when the [16:9], [15:9], or [16:10] aspect ratios are selected. • The term “letterbox” refers to a more landscape-oriented image when compared to a 4:3 image, which is the standard aspect ratio for a vide source. The letterbox signal has aspect ratios with the vista size “1.85:1” or cinema scope size “2.35:1” for movie film. • The term “squeeze” refers to the compressed image of which aspect ratio is converted from 16:9 to 4:3. [INPUT RESOLUTION] The resolution is assigned automatically when the resolution of the input signal from the computer video input terminal (analog RGB) cannot be distinguished.
Page 112: [Video]
5. Using On-Screen Menu [VIDEO] Using Noise Reduction [NOISE REDUCTION] When projecting a video image, you can use the [NOISE REDUCTION] function to reduce the screen noise (roughness and distortion). This device is equipped with three types of noise reduction functions. Select the function according to the type of noise. Depending on the noise level, the noise reduction effect can be set to [OFF], [LOW], [MEDIUM] or [HIGH]. [NOISE REDUCTION] can be selected for SDTV, HDTV signal and component signal input. RANDOM NR �� Reduces flickering random noise in an image� MOSQUITO NR �� Reduces mosquito noise that appears around the edges of an image during Blu-ray playback� BLOCK NR �� Reduces block noise or mosaic-like patterns� Selecting Interlaced Progressive Conversion Process Mode [DEINTERLACE] This function allows you to select an interlaced-to-progressive conversion process for video signals.
Page 113 5. Using On-Screen Menu [SIGNAL TYPE] Selection of RGB and component signals. Normally, this is set to [AUTO]. Please change the setting if the color of the image remains unnatural. AUTO �� Automatically distinguishes RGB and component signals� RGB �� Switches to the RGB input� REC601 �� Switches to the component signal conforming to the ITU-R Rec601 standard� Setting appropriate to SDTV images� REC709 ��...
Page 114: [3D Settings]
5. Using On-Screen Menu [3D SETTINGS] Please refer to “3-10 Projecting 3D videos” (→ page 44) for the operation. STEREO VIEWER Stack up a single or multiple projectors and carry out the settings for projecting 3D videos. Select the left / right set- tings of the 3D eyewear using the stereo viewer. SINGLE �� Use a single projector to project 3D videos� DUAL LEFT �� Use a dedicated projector for displaying videos on the left� DUAL RIGHT �� Use a dedicated projector for displaying videos on the right� STEREO FILTER Stack up a single or multiple projectors and carry out the settings for projecting 3D videos. Image setting for 3D glasses made by Infitec.
Page 115: Using The Lens Memory Function [Lens Memory]
5. Using On-Screen Menu Using the Lens Memory Function [LENS MEMORY] This function serves to store the adjusted values for each input signal when using the LENS SHIFT, ZOOM and FO- CUS buttons of the projector. Adjusted values can be applied to the signal you selected. This will eliminate the need to adjust lens shift, focus, and zoom at the time of source selection. STORE �� Stores the current adjusted values in memory for each input signal� MOVE �� Applies the adjusted values to the current signal� RESET �� Returns the adjusted values to the last condition� NOTE: • Lens memory adjustments will be automatically registered the ENTRY LIST. These lens memory adjustments can be loaded from the ENTRY LIST. (→ page 83)
Page 116 5. Using On-Screen Menu To call up the adjusted values from [LENS MEMORY]: 1. From the menu, select [ADJUST] → [LENS MEMORY] → [MOVE] and press the ENTER button. The confirmation screen will be displayed. 2. Press the ◀ button to select and [YES] and press the ENTER button. During projection, if the adjusted values for an input signal have been saved, the lens will shift. If not, the lens will shift according to the adjusted values stored in the selected [REF. LENS MEMORY] [PROFILE] number. To automatically apply the adjusted values at the time of source selection: 1. From the menu, select [SETUP] → [INSTALLATION(1)] → [REF. LENS MEMORY] → [LOAD BY SIGNAL] and press the ENTER button.
Page 117: ❻ Menu Descriptions & Functions [Display]
5. Using On-Screen Menu ❻ Menu Descriptions & Functions [DISPLAY] [PIP/PICTURE BY PICTURE] SUB INPUT Select the input signal to be displayed in the sub-display. Please refer to “4-2 Displaying Two Pictures at the Same Time” (→ page 64) for details on the operation. MODE Select either PIP (PICTURE IN PICTURE) or PICTURE BY PICTURE when switching to 2-screen display. PICTURE SWAP The videos in the main display and sub-display will be switched. Please refer to “4-2 Displaying Two Pictures at the Same Time” (→ page 64) for details. PIP SETTING Select the display position, position adjustment and size of the sub-display in the PIP screen. START POSITION �� Selection of the display position of the sub-display when switching to the PIP screen� HORIZONTAL POSITION ��...
Page 118 5. Using On-Screen Menu TIP: The horizontal position and vertical position are the amount of movement from the reference points. For example, when TOP-LEFT is adjusted, the position is displayed with the same amount of movement even if displayed with other starting positions. The maximum amount of movement is half the resolution of the projector. Reference point Adjust using the horizon- Reference point tal position Adjust using the vertical position TOP-LEFT TOP-RIGHT BOTTOM-LEFT BOTTOM-RIGHT Sub-display Main display Reference point Reference point BORDER Select the display boundary of the main display and sub-display of the [PICTURE BY PICTURE] screen. Main display Sub-display Main display Sub-display Main display Sub-display...
Page 119: [Geometric Correction]
5. Using On-Screen Menu [GEOMETRIC CORRECTION] MODE Set pattern for correcting distortion. If [OFF] is selected, the [GEOMETRIC CORRECTION] becomes ineffective. If you need to change the [MENU ANGLE], make sure to change it before performing the [GEOMETRIC CORREC- TION]. If [MENU ANGLE] is changed after performing the [GEOMETRIC CORRECTION], corrected values will be reset to the default values. KEYSTONE Correct distortion in horizontal and vertical directions. HORIZONTAL �� Adjustments when projecting from a diagonal direction to the screen� VERTICAL �� Adjustments when projecting from the top or bottom direction to the screen�...
Page 120 5. Using On-Screen Menu CORNERSTONE Display the 4-point correction screen and adjust the trapezoidal distortion of the projection screen. Please refer to “Correcting Horizontal and Vertical Keystone Distortion [CORNERSTONE]” (→ page 36) for details on the operation. HORIZONTAL CORNER/VERTICAL CORNER Distortion correction for corner projection such as wall surfaces. HORIZONTAL CORNER �� Performs correction for projection onto a wall lying at an angle to the horizontal direction� * Reverse angle correction is also possible� VERTICAL CORNER ��...
Page 121 5. Using On-Screen Menu Adjustment method 1. Align the cursor with the [HORIZONTAL CORNER] or [VERTICAL CORNER] of the [GEOMETRIC CORREC- TION] menu and then press the ENTER button. • The adjustment screen will be displayed. 2. Press the ▼▲◀▶ buttons to align the cursor (yellow box) with the target adjustment point and then press the ENTER button. • The cursor will change into an adjustment point (yellow in color). 3. Press the ▼▲◀▶ buttons to adjust the corners or sides of the screen and then press the ENTER button. • The adjustment point will go back to being a cursor (yellow box). Explanation of screen transition • The adjustment points of the four corners (a, c, f and h in the drawing) will move independently. • The following adjustment points differ at the [HORIZONTAL CORNER] and [VERTICAL CORNER]. HORIZONTAL CORNER: When Point b in the drawing is moved, and the upper side and Point g are moved, the lower side will move in a parallel manner.
Page 122 5. Using On-Screen Menu WARP Correct projected image distortion on a specific surface as a column or a sphere. NOTE: • When the maximum adjustment range is exceeded, distortion adjustment is disabled. Set up the projector at an optimal angle since the more the adjustment volume gets large, the more image quality gets deterioration. • Please note that the image will go out of focus due to the difference in the distance between peripheries and the center of the screen for projections cutting across corners as on a column or a sphere. Lenses with short focal points are also not recommended for projections cutting across corners as the image will go out of focus. Adjustment method 1. Align the cursor with the [WARP] of the [GEOMETRIC CORRECTION] menu and the press the ENTER. • Adjustment screen will be displayed on. 2. Press the ▼▲◀▶ buttons to align the cursor (blue box) with the target adjustment point and then press the ENTER. • The cursor will change into an adjustment point (yellow in color). 3. Press the ▼▲◀▶ buttons to adjust the corners or sides of the screen and then press the ENTER. • The cursor will back to yellow box. Explanation for correcting distortion • Eight adjustment points can be moved independently. • For left and right sides, use ◀/▶ buttons for adjusting the range of distortion, and ▼/▲ buttons for adjusting the distortion peak.
Page 123 5. Using On-Screen Menu PC TOOL Recall the geometric correction data that is registered in the projector beforehand. Three types of correction data can be registered. NOTE: • As electrical correction is carried out in geometric correction, the brightness may be affected and the picture quality may be degraded. RESET Reset the adjustment value that has been set up as MODE in GEOMETRIC CORRECTION (return to the initial value). • This is ineffective when MODE is set OFF. • Reset can be executed by pressing and holding the Geometeric. button on the remote control for over 2 seconds.
Page 124: [Edge Blending]
5. Using On-Screen Menu [EDGE BLENDING] This adjusts the edges (boundaries) of the projection screen when projecting high resolution videos using a combina- tion of several projectors in the up, down, left and right positions. MODE This enables or disables the EDGE BLENDING function. When MODE is set to ON, the TOP, BOTTOM, LEFT, RIGHT, BLACK LEVEL and BLEND CURVE settings can be adjusted. TOP/BOTTOM/LEFT/RIGHT This selects the EDGE BLENDING locations on the left, right, top and bottom on the screen. The following settings can be adjusted when an item is selected. (→ page 69) CONTROL �� Enable TOP, BOTTOM, LEFT and RIGHT functions� MARKER �� Set whether to display marker or not when adjusting the range and display position� When turned on, a magenta marker for adjusting the range adjustment and a green marker for adjusting the display position will be displayed�...
Page 125: [Multi Screen]
5. Using On-Screen Menu [MULTI SCREEN] WHITE BALANCE This adjusts the white balance for each projector when projecting using a combination of several projectors. This can be adjusted when [MODE] is set to [ON]. CONTRAST W, CONTRAST R, CONTRAST G, CONTRAST B �� Adjusting the white color of the video� BRIGHTNESS W, BRIGHTNESS R, BRIGHTNESS G, BRIGHTNESS B �� Adjusting the black color of the video� PICTURE SETTING This sets the division condition when projecting using a combination of several projectors.
Page 126 5. Using On-Screen Menu Conditions for using tiling • All the projectors need to fulfil the following conditions. • The panel size must be the same • The projection screen size must be the same • The left and right ends or top and bottom ends of the projection screen must be consistent. • The settings for the left and right edges of the edge blending are the same • The settings for the top and bottom edges of the edge blending are the same If the tiling conditions are satisfied, the video screen of the projector at each installation position will be automati- cally extracted and projected. If the tiling conditions are not satisfied, adjust the video screen of the projector at each installation position using the zoom function. • Assign a unique control ID to each projector. • Set the “Color setting” and “DeepColor setting” on your Blu-ray player or computer to “Auto” . Refer to the owner’s manual accompanied with your Blu-ray player or computer for more information. Connect an HDMI output signal of your Blu-ray player or computer to the first projector and then connect to the HDBaseT OUT/Ethernet port on the first projector to the HDBaseT IN/Ethernet port on the second projector, same to the sequel projectors.. Tiling setting example) Number of horizontal units = 2, Number of vertical units = 2 Horizontal order = Second unit Vertical order = First unit...
Page 127: ❼ Menu Descriptions & Functions [Setup]
5. Using On-Screen Menu ❼ Menu Descriptions & Functions [SETUP] [MENU(1)] Selecting Menu Language [LANGUAGE] You can choose one of 30 languages for on-screen instructions. NOTE: Your setting will not be affected even when [RESET] is done from the menu. Selecting Menu Color [COLOR SELECT] You can choose between two options for menu color: COLOR and MONOCHROME. Turning On / Off Source Display [INPUT DISPLAY] This option turns on or off input name display such as HDMI1, HDMI2, DisplayPort, COMPUTER, HDBaseT to be displayed on the top right of the screen. Turning messages on and off [MESSAGE DISPLAY] This option selects whether or not to display projector messages at the bottom of the projected image. Even when “OFF” is selected, the security lock warning is displayed. The security lock warning turns off when the security lock is canceled. Turning ON/OFF Control ID [ID DISPLAY] ID DISPLAY �� This option turns on or off the ID number which is displayed when the ID SET button on the remote control is pressed�...
Page 128: [Menu(2)]
5. Using On-Screen Menu [MENU(2)] [MENU ANGLE] Select the direction for displaying the menu. [MENU POSITION] Shift the menu displaying position. HORISONTAL POSITION ��Shift the menu in the horizontal directions� VERTICAL POSITION ��Shift the menu in the vertical directions� RESET ��Reset the menu displaying position to the default factory setting (the screen center)� TIP • Once the projector is powered off, the menu displaying position will reset to the default factory setting.
Page 129: [Installation(1)]
5. Using On-Screen Menu [INSTALLATION(1)] Selecting Projector Orientation [ORIENTATION] This reorients your image for your type of projection. The options are: desktop front projection, ceiling rear projection, desktop rear projection, and ceiling front projection. NOTE: • Please consult the dealer if you require special installation services e.g. when mounting the projector to a ceiling. Never install the projector on your own. This may result in the projector falling down and causing injury to people. AUTO �� This automatically detects and projects the DESKTOP FRONT and CEILING FRONT� NOTE: • The DESKTOP REAR and CEILING REAR will not be detected. Please select manually. DESKTOP FRONT CEILING REAR DESKTOP REAR CEILING FRONT TIP: • Check whether the automatic DESKTOP FRONT is installed within ± 10 degrees for floor installation and whether the CEILING FRONT is within ±10 degrees for ceiling installation. Select manually when the projection screen is inverted.
Page 130 5. Using On-Screen Menu Selecting Aspect Ratio and Position for Screen [SCREEN] [SCREEN TYPE] Sets the aspect ratio of the projection screen. FREE �� The ratio of the liquid crystal panel is selected� Select this when projecting multi-screen and 17:9 screen (2K)� 4:3 SCREEN �� For a screen with a 4:3 aspect ratio 16:9 SCREEN �� For a screen with a 16:9 aspect ratio 16:10 SCREEN ��...
Page 131 5. Using On-Screen Menu TIP: • When [HIGH ALTITUDE] is selected for [FAN MODE], a symbol icon will be displayed at the bottom of the menu. [LIGHT MODE] Adjusting the energy savings settings and the brightness of each projector in multi-screen projection. For energy savings settings, see page 33 “3-6. Changing LIGHT MODE/Checking Energy-Saving Effect Using LIGHT MODE [LIGHT MODE]”. LIGHT MODE NORMAL The light module luminance (brightness) will become 100% and the screen will turn bright. ECO1 By controlling the brightness and fan speed according to the selected setting, energy can be saved and motion noise and the power consumption can be lowered. ECO2 LONG LIFE The mode optimizes the service life of the optimal parts. The brightness is about 30% of NORMAL. CONSTANT [CONSTANT BRIGHTNESS] mode will be canceled.
Page 132 5. Using On-Screen Menu [STATIC CONVERGENCE] This features allows you to adjust for color deviation in the picture. This can be adjusted in units of ± 1 pixel in the horizontal direction for HORIZONTAL R, G and B, in the vertical direc- tion for VERTICAL R, G and B. Using the Reference Lens Memory Function [REF. LENS MEMORY] This function serves to store the adjusted values common to all input sources when using the LENS SHIFT, ZOOM and FOCUS buttons of the projector or the remote control. The adjusted values stored in memory can be used as a reference to the current. PROFILE �� Select a stored [PROFILE] number� STORE �� Stores the current adjusted values in memory as a reference� MOVE �� Applies the adjusted reference values stored in [STORE] to the current signal� RESET ��...
Page 133: [Installation(2)]
5. Using On-Screen Menu [INSTALLATION(2)] [SHUTTER SETTINGS] Enabling and disabling the lens shutter function. You can also set how long the light will take to fade in and fade out when either the SHUTTER button on the remote control. POWER ON OPEN When the power is turned on, the light source comes on and the picture is SHUTTER projected. CLOSE The light source does not come on when the power is turned on. When the SHUTTER button is pressed, the shutter is released and the light source is turned on. FADE IN TIME Set how long the light will take to fade in after the SHUTTER button is pressed. The time can be set from 0 to 10 seconds in increments of 1 second. FADE OUT TIME Set how long the light will take to fade out after the SHUTTER button is pressed. The time can be set from 0 to 10 seconds in increments of 1 second.
Page 134: [Control]
5. Using On-Screen Menu [CONTROL] TOOLS ADMINISTRATOR MODE This allows you to select MENU MODE, save settings, and set a password for the administrator mode. MENU MODE Select either [BASIC] or [ADVANCED] menu. — (→ page 76) NOT SAVE SETTING Placing a check mark will not save your projector settings. — VALUES Clear this check box to save your projector settings. NEW PASSWORD/ Assign a password for the administrator mode. Up to 10 alphanumeric CONFIRM PASS- characters WORD...
Page 135 5. Using On-Screen Menu PROGRAM TIMER This option turns on/standby the projector and changes video signals, and selects LIGHT mode automatically at a specified time. NOTE: • Before using [PROGRAM TIMER], make sure that the [DATE AND TIME] feature is set. (→ page 120) Make sure that the projector is in the standby condition with the POWER cord connected. The projector has a built-in clock. The clock will keep working for about a month after the main power is turned off. If the main power is not supplied to the projector for a month or more, it requires to set [DATE AND TIME SETTINGS] feature again. Setting a new program timer 1. On the PROGRAM TIMER screen, use the ▲ or ▼ button to select [SETTINGS] and press the ENTER button. The [PROGRAM LIST] screen will be displayed. 2. Select a blank program number and press the ENTER button. The [ (EDIT)] screen will be displayed. 3. Make settings for each item as required. ACTIVE ��...
Page 136 5. Using On-Screen Menu DAY �� Select days of the week for the program timer� To execute the program from Monday to Friday, select [MON- FRI]� To execute the program in everyday basis, select [EVERYDAY]� TIME �� Set the time to execute the program� Enter time in 24-hour format� FUNCTION ��...
Page 137 5. Using On-Screen Menu Activating the program timer 1. Select [ENABLE] on the [PROGRAM TIMER] screen and press the ENTER button. The selection screen will be displayed. 2. Press the ▼ button to align the cursor with [ON] and then press the ENTER button. Return to the [PROGRAM TIMER] screen. NOTE: • When the effective settings of the [PROGRAM TIMER] have not been set to [ON], the program will not be executed even if the [ACTIVE] items in the program list have been ticked. • Even when the effective settings of the [PROGRAM TIMER] are set to [ON], the [PROGRAM TIMER] will not work until the [PRO- GRAM TIMER] screen is closed. Editing the programmed settings 1. On the [PROGRAM LIST] screen, select a program you want to edit and press the ENTER button. 2. Change the settings on the [EDIT] screen. 3. Select [OK] and press the ENTER button. The programmed settings will be changed.
Page 138 5. Using On-Screen Menu DATE AND TIME SETTINGS You can set the current time, month, date, and year. NOTE: The projector has a built-in clock. The clock will keep working for about a month after the main power is turned off. If the main power is off for a month or more, the built-in clock will cease. If the built-in clock ceases, set the date and time again. The built-in clock will not cease while in the standby mode. In order to activate the built-in clock continuously even when the projector is not used, leave it in the standby state not plugging off the power cord. TIME ZONE SETTINGS �� Select your time zone� DATE AND TIME SETTINGS �� Set your current date (MM/DD/YYYY) and time (HH:MM)� INTERNET TIME SERVER: If you place a check mark, the projector’s built-in clock will be syn- chronized with an Internet time server in every 24 hours and at the time of projector’s startup�...
Page 139 5. Using On-Screen Menu Setting ID to the Projector [CONTROL ID] You can operate multiple projectors separately and independently with the single remote control that has the CONTROL ID function. If you assign the same ID to all the projectors, you can conveniently operate all the projectors together using the single remote control. To do so, you have to assign an ID number to each projector. CONTROL ID NUMBER ��Select a number from 1 to 254 you wish to assign to your projector� CONTROL ID ��Select [OFF] to turn off the CONTROL ID setting and select [ON] to turn on the CONTROL ID setting� NOTE: • When [ON] is selected for [CONTROL ID], the projector cannot be operated by using the remote control that does not support the CONTROL ID function. (In this case the buttons on the projector cabinet can be used.)
Page 140 5. Using On-Screen Menu Turning On or Off Remote Sensor [REMOTE SENSOR] This option determines which remote sensor on the projector is enabled in wireless mode. The options are: FRONT/BACK, FRONT, BACK, and HDBaseT*. NOTE: • The remote control of the projector will not be able to receive signals if the power supply of the HDBaseT transmission device connected to the projector is switched on when this has been set to “HDBaseT”. TIP: • If the remote control system does not function when direct sunlight or strong illumination strikes the remote control sensor of the projector, change to other option.
Page 141: [Network Settings]
5. Using On-Screen Menu [NETWORK SETTINGS] Important: • Consult with your network administrator about these settings. • When using a wired LAN, connect the Ethernet cable (LAN cable) to the LAN port on the projector. (→ page 150) • Please use a shielded twisted pair (STP) cable of Category 5e or higher for the LAN cable (sold commercially). TIP: The network settings you make will not be affected even when [RESET] is done from the menu. Hints on How to Set Up LAN Connection To set up the projector for a LAN connection: Select [WIRED LAN] → [PROFILES] → [PROFILE 1] or [PROFILE 2]. Two settings can be set for wired LAN. Next turn on or off for [DHCP], [IP ADDRESS], [SUBNET MASK], and [GATEWAY] and select [OK] and press the ENTER button. (→ page 124) To recall LAN settings stored in the profile number: Select [PROFILE 1] or [PROFILE 2] for wired LAN, and then select [OK] and press the ENTER button. (→ page 124) To connect a DHCP server: Turn on [DHCP] for wired LAN. Select [ON] and press the ENTER button. To specify IP address without using the DHCP server, turn off [DHCP]. (→ page 124) To receive error messages via e-mail:...
Page 142 5. Using On-Screen Menu WIRED LAN INTERFACE Select [LAN] for using the LAN port for connecting to the wired — LAN. Select [HDBaseT] for using the HDBaseT IN/Ethernet port for connecting to the wired LAN. The control from the connected device will be disabled if no signal is sent and received for three minutes if the projector is connected to wired LAN thru the HD- BaseT IN/Ethernet. For refusing this, set the standby mode to [SLEEP] in advance. PROFILES • The settings for the wired LAN can be recorded in the projector — memory in two ways. • Select [PROFILE 1] or [PROFILE 2] and then do settings for [DHCP] and the other options. After doing this, select [OK] and press the ENTER button. This will store your settings in memory. • To recall the settings from memory: After selecting [PROFILE 1] or [PROFILE 2] from the [PRO- FILES] list. Select [OK] and press the ENTER button. • Select [DISABLE] when not connecting to a wired LAN DHCP Place a check mark to automatically assign an IP address to the — projector from your DHCP server. Clear this check box to register the IP address or subnet mask number obtained from your network administrator.
Page 143 5. Using On-Screen Menu PROJECTOR NAME PROJECTOR NAME Set a unique projector name. Up to 16 alphanu- meric characters and symbols DOMAIN Set a host name and domain name of the projector. HOST NAME Set a host name of the projector. Up to 16 alphanumeric characters DOMAIN NAME Set a domain name of the projector. Up to 60 alphanumeric characters...
Page 144 5. Using On-Screen Menu ALERT MAIL ALERT MAIL This option will notify your computer of error messages via e-mail — when using wireless or wired LAN. Placing a checkmark will turn on the Alert Mail feature� Clearing a checkmark will turn off the Alert Mail feature� Sample of a message to be sent from the projector: Subject: [Projector] Projector Information THE COOLING FAN HAS STOPPED. [INFORMATION] PROJECTOR NAME: xxxxx LIGHT HOURS USED: xxxx[H] HOST NAME Type in a host name. Up to 16 alphanumeric characters DOMAIN NAME Type in a domain name of the network connected to the projector.
Page 145 5. Using On-Screen Menu NETWORK SERVICE HTTP SERVER Set a password for your HTTP server. Up to 10 alphanumeric characters PJLink This option allows you to set a password when you use the Up to 32 alphanumeric PJLink feature. characters NOTE: • Do not forget your password. However, if you forget your password, consult with your dealer. • What is PJLink? PJLink is a standardization of protocol used for controlling projectors of different manufacturers. This standard protocol is established by Japan Business Machine and Information System Industries Associa- tion (JBMIA) in 2005.
Page 146: [Source Options]
5. Using On-Screen Menu [SOURCE OPTIONS] Setting Auto Adjust [AUTO ADJUST] This feature sets the Auto Adjust mode so that the computer signal can be automatically or manually adjusted for noise and stability. You can automatically make adjustment in two ways: [NORMAL] and [FINE]. OFF �� The computer signal will not be automatically adjusted� You can manually optimize the computer signal� NORMAL �� Default setting� The computer signal will be automatically adjusted� Normally select this option� FINE ��...
Page 147 5. Using On-Screen Menu [HDBaseT OUT SELECT] Select signal to output from the HDBaseT OUT/Ethernet port on the projector. When two images are projected simul- taneously (PIP/PICTURE BY PICTURE), the image for the main screen is output. AUTO �� Output the input signal� When [PIP] has been set, the input signal for the main screen is output� HDMI1 �� Output the input signal thru the HDMI 1 IN terminal� HDMI2 �� Output the input signal thru the HDMI 2 IN terminal� DisplayPort ��...
Page 148: [Power Options]
5. Using On-Screen Menu [POWER OPTIONS] [STANDBY MODE] Select the standby mode: NORMAL �� Automatically transit the standby state and control consumption power based on the projector setting and the state of the connected device� (→ page 168) SLEEP �� Maintain the state of sleep� Consumption power becomes higher than the setting of NORMAL� Select this mode in the following cases: • For using the HDBaseT IN/Ethernet and HDBaseT OUT/Ethernet ports constantly.
Page 149 5. Using On-Screen Menu Enabling Power Management [AUTO POWER OFF] When this option is selected you can enable the projector to automatically turn off (at the selected time: 0:05, 0:10, 0:15, 0:20, 0:30, 1:00) if there is no signal received by any input or if no operation is performed. Using Off Timer [OFF TIMER] 1. Select your desired time between 30 minutes and 16 hours: OFF, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00. 2. Press the ENTER button on the remote control. 3. The remaining time starts counting down and it is displayed at the bottom of the On-Screen Menu. 4. The projector will turn off after the countdown is complete. NOTE: • To cancel the preset time, set [OFF] for the preset time or turn off the power. • When the remaining time reaches 3 minutes before the projector is turned off, the [THE PROJECTOR WILL TURN OFF WITHIN 3 MINUTES] message will be displayed on the bottom of the screen.
Page 150: Returning To Factory Default [Reset]
5. Using On-Screen Menu Returning to Factory Default [RESET] The RESET feature allows you to change adjustments and settings to the factory preset for a (all) source (s) except the following: [CURRENT SIGNAL] Resets the adjustments for the current signal to the factory preset levels. The items that can be reset are: [PRESET], [CONTRAST], [BRIGHTNESS], [COLOR], [HUE], [SHARPNESS], [AS- PECT RATIO], [HORIZONTAL], [VERTICAL], [CLOCK], [PHASE], and [OVERSCAN]. [ALL DATA] Reset all the adjustments and settings for all the signals to the factory preset. All items can be reset EXCEPT [ENTRY LIST], [LANGUAGE], [BACKGROUND], [EDGE BLENDING], [MULTI SCREEN], [SCREEN TYPE], [GEOMETRIC CORRECTION], [REF. WHITE BALANCE], [STATIC CONVERGENCE], [ADMINISTRATOR MODE], [CONTROL PANEL LOCK], [SECURITY], [COMMUNICATION SPEED], [DATE AND TIME SETTINGS], [CONTROL ID], [STANDBY MODE], [FAN MODE], [REF. LENS MEMORY], [EDID VERSION], [HDCP VERSION], [LIGHT HOURS USED], [TOTAL CARBON SAVINGS], [WIRED LAN]. [ALL DATA (INCLUDING ENTRY LIST)] Reset all the adjustments and settings for all the signals including the [ENTRY LIST] to the factory preset except [LANGUAGE], [BACKGROUND], [EDGE BLENDING], [MULTI SCREEN], [SCREEN TYPE], [GEOMETRIC COR- RECTION], [REF. WHITE BALANCE], [STATIC CONVERGENCE], [ADMINISTRATOR MODE], [CONTROL PANEL LOCK], [SECURITY], [COMMUNICATION SPEED], [DATE AND TIME SETTINGS], [CONTROL ID], [STANDBY MODE], [FAN MODE], [REF. LENS MEMORY], [EDID VERSION], [HDCP VERSION], [LIGHT HOURS USED], [TO- TAL CARBON SAVINGS], [WIRED LAN].
Page 151: ❽ Menu Descriptions & Functions [Info.]
5. Using On-Screen Menu ❽ Menu Descriptions & Functions [INFO.] Displays the status of the current signal and light module usage. This item has ten pages. The information included is as follows: TIP: Pressing the HELP button on the remote control will show the [INFO.] menu items. [USAGE TIME] [LIGHT HOURS USED] (H) [TOTAL CARBON SAVINGS] (kg-CO2) • [TOTAL CARBON SAVINGS] This displays the estimated carbon saving information in kg. The carbon footprint factor in the carbon saving cal- culation is based on the OECD (2008 Edition). (→ page 35)
Page 152: [Source(1)]
5. Using On-Screen Menu [SOURCE(1)] INPUT TERMINAL RESOLUTION HORIZONTAL FREQUENCY VERTICAL FREQUENCY SYNC TYPE SYNC POLARITY SCAN TYPE SOURCE NAME ENTRY NO. [SOURCE(2)] SIGNAL TYPE BIT DEPTH VIDEO LEVEL SAMPLING FREQUENCY 3D FORMAT [SOURCE(3)] INPUT TERMINAL RESOLUTION HORIZONTAL FREQUENCY VERTICAL FREQUENCY SYNC TYPE SYNC POLARITY SCAN TYPE SOURCE NAME ENTRY NO.
Page 153: [Source(4)]
5. Using On-Screen Menu [SOURCE(4)] SIGNAL TYPE BIT DEPTH VIDEO LEVEL SAMPLING FREQUENCY 3D FORMAT [WIRED LAN] IP ADDRESS SUBNET MASK GATEWAY MAC ADDRESS [VERSION(1)] FIRMWARE DATA FIRMWARE2...
Page 154: [Others]
5. Using On-Screen Menu [OTHERS] DATE TIME PROJECTOR NAME MODEL NO. SERIAL NUMBER LENS ID [CONDITIONS] INTAKE TEMPERATURE EXHAUST TEMPERATURE ATMOSPHERIC PRESSURE INSTALLATION POSITION X-AXIS Y-AXIS Z-AXIS About the X-AXIS, Y-AXIS and Z-AXIS CONDITIONS * Arrow direction of the Z-AXIS in the figure represents the top of the projector. X-AXIS �� Display the projector image at an angle of −100 – +100 X-AXIS value of degrees to the horizontal in the X-axis direction� the projector Horizontal plane X-axis...
Page 155: [Hdbaset]
5. Using On-Screen Menu Z-AXIS �� Display the projector image at an angle of −100 – +100 Z-AXIS value of degrees to the vertical in the Z-axis direction� the projector Horizontal plane Z-axis Gravity direction [HDBaseT] SIGNAL QUALITY OPERATION MODE LINK STATUS HDMI STATUS...
Page 156: Connecting To Other Equipment
6. Connecting to Other Equipment ❶ Mounting a lens (sold separately) Three separate bayonet style lenses can be used with this projector. The descriptions here are for the NP41ZL lens. Mount other lenses in the same manner. WARNING: (1) Turn off the power and wait for the cooling fan to stop, (2) disconnect the power cord and wait for the unit to cool before mounting or removing the lens. Failure to do so can result in eye injury, electric shock, or burn injuries. Important: • Be sure to carry out [LENS CALIBRATION] after replacing the lens. • The projector and lenses are made of precision parts. Do not subject them to shock or excessive forces. • Remove the separately sold lens when moving the projector. If not, the lens could be subject to shock while the projector is being moved, damaging the lens and the lens shift mechanism. • When dismounting the lens from the projector, return the lens position to the home position before turning off the power. Failure to do so may prevent the lens from being mounted or dismounted because of narrow space between the projector and the lens. • Never touch the lens surface while the projector is operating. • Be very careful not to let dirt, grease, etc., on the lens surface and not to scratch the lens surface. • Perform these operations on a flat surface over a piece of cloth, etc., to prevent the lens from getting scratched. • When leaving the lens off the projector for long periods of time, mount the dust cap on the projector to prevent dust or dirt from getting inside.
Page 157 6. Connecting to Other Equipment 3. Insert the lens onto the projector facing the arrow on the lens-label upward. Guiding notch Insert the lens slowly all the way in. Arrow Protrusion 4. Turn the lens clockwise. Turn until a click is heard. The lens is now fastened onto the projector. TIP: Mounting the lens theft prevention screw Fasten the lens theft prevention screw included with the projector to the bottom of the projector so that the lens cannot be removed easily.
Page 158: Removing The Lens
6. Connecting to Other Equipment Removing the lens Preparations: 1. Turn on the projector and display an image. 2. Press and hold the SHIFT/HOME POSITION button over 2 seconds. The lens position will be moved to the home position. 3. Turn off the main power switch, and then unplug the power cord. 4.
Page 159: ❷ Making Connections
6. Connecting to Other Equipment ❷ Making Connections A computer cable, HDMI cable, or a DisplayPort cable can be used to connect to a computer. The connection cable is not enclosed with the projector. Please get ready a suitable cable for the connection. Analog RGB signal connection • Connect the computer cable to the monitor out terminal (mini D-sub 15 pin) on the computer and the computer video input terminal on the projector. Please use a computer cable attached with a ferrite core. AUDIO IN COMPUTER IN AUDIO OUT Stereo mini-plug audio cable (not supplied) Computer cable (sold commercially) NOTE: • Please check the operating manual of the computer as...
Page 160: Digital Rgb Signal Connection
6. Connecting to Other Equipment Digital RGB signal connection • Connect a commercially available HDMI cable between the computer’s HDMI output connector and the projector’s HDMI 1 IN or HDMI 2 IN connector. • Connect a commercially available DisplayPort cable between the computer’s DisplayPort output connector and the projector’s DisplayPort input connector. HDMI 1 IN DisplayPort IN HDMI 2 IN DisplayPort cable (not supplied) HDMI cable (not supplied) • Select the source name for its appropriate input connector after turning on the projector. Input connector INPUT button on the projector Button on the remote control cabinet HDMI 1 IN 1:HDMI 1 1/HDMI 1 HDMI 2 IN 2:HDMI 2 2/HDMI 2...
Page 161 6. Connecting to Other Equipment Cautions when using a DVI signal • When the computer has a DVI output connector, use a commercially available converter cable to connect the computer to the projector’s HDMI 1 IN or HDMI 2 IN connector (only digital video signals can be input). Also, con- nect the computer’s audio output to the projector’s audio input connector. In this case, switch the HDMI1 or HDMI2 setting at on-screen menu’s audio selection on the projector to [COMPUTER]. (→ page 128) To connect the computer’s DVI output connector to the projector’s DisplayPort input connector, use a commercially available converter. HDMI 2 IN AUDIO IN HDMI 1 IN AUDIO OUT NOTE: When Viewing a DVI Digital Signal • Turn off the power of the computer and projector before connecting.
Page 162: Connecting Component Input
6. Connecting to Other Equipment Connecting Component Input COMPUTER IN 15-pin - to - RCA (female) × 3 cable adapter (ADP-CV1E) Component video RCA × 3 cable (not supplied) Audio Equipment Blu-ray player Stereo mini plug - to - RCA audio cable (not supplied) • Select the source name for its appropriate input connector after turning on the projector.
Page 163: Connecting Hdmi Input
6. Connecting to Other Equipment Connecting HDMI Input You can connect the HDMI output of your Blu-ray player, hard disk player, or notebook type PC to the HDMI 1 IN or HDMI 2 IN connector of your projector. HDMI 1 IN HDMI 2 IN AUDIO OUT HDMI cable (not supplied) Audio cable (not supplied) Use High Speed HDMI Cable. ® Input connector INPUT button on the projector Button on the remote control cabinet HDMI 1 IN 1:HDMI 1 1/HDMI 1 HDMI 2 IN 2:HDMI 2 2/HDMI 2 TIP: For users of audio video equipment with an HDMI connector:...
Page 164: Connecting To A Hdbaset Transmission Device (Sold Commercially)
6. Connecting to Other Equipment Connecting to a HDBaseT transmission device (sold commercially) Use a LAN cable sold commercially to connect the HDBaseT IN/Ethernet port of the projector (RJ-45) to a HDBaseT transmission device sold commercially. The HDBaseT IN/Ethernet port of the projector supports HDMI signals (HDCP) from transmission devices, control signals from external devices (serial, LAN) and remote control signals (IR commands). • Refer to the owner’s manual accompanied with your HDBaseT transmission for connecting with your external de- vices. Connection example Computer (for output use) Computer (for control use) Our company’s remote control (RD-465E) Wired-Remote AUDIO IN HDMI IN COMPUTER IN RS-232C...
Page 165: Connecting Several Projectors
6. Connecting to Other Equipment Connecting several projectors It enables to project HDMI, DisplayPort, HDBaseT image on several projectors connecting the HDBaseT IN/Ethernet port and the HDBaseT OUT/Ethernet port by LAN cable. The projectors support same brightness can be connected up to four units, HDBaseT OUT/Ethernet Master projector HDBaseT IN/Ethernet Other projector • The signal from the COMPUTER IN terminal is not output from the HDBaseT OUT/Ethernet port of this projector. 6780WUSS and 6765WUSS cannot be connected. At the same time, this projector is not guaranteed to work • correctly in the connection with an other device as a monitor. • When outputting HDMI signals, turn on the power of the video device on the output side and keep it connected before inputting video signals into this device. T he HDMI output terminals of the projector are equipped with repeater functions. When a device is connected to the HDMI output terminal, the resolution of the output signal is limited by the resolution supported by the connected device.
Page 166: Portrait Projection (Vertical Orientation)
6. Connecting to Other Equipment Portrait projection (vertical orientation) Portrait screens from a computer can be projected by installing the projec- tor in a vertical orientation. Angle to display all the screens such as the on-screen menu can be changed by the menu [SETUP] → [MENU(2)] → [MENU ANGLE]. Precautions during installation • Please do not install the projector in a vertical orientation on top of the floor or table on its own. The intake vent may be obstructed, resulting in the projector getting warm and the possibility of fire and malfunction occurring. • A stand for supporting the projector needs to be made for portrait projection and for installing the projector in universal angle. In this case, the stand must be designed such that the center of gravity of the projector is located well within the legs of the stand. If not, the projector may fall over and result in injury, damage and malfunction. Design and manufacturing conditions for the stand Please engage an installation service provider for the design and manufacture of the customized stand to be used for portrait projection. Please ensure that the following are complied with when designing the stand. 1. Secure sufficient space between the projector and the floor: Installation facing the intake vent downward: 130 mm or greater. Installation facing the exhaust vent downward: 200 mm or greater. 2. Use the four screw holes at the back of the projector to secure it to the stand. Screw hole center dimension: 200 × 250 mm Screw hole dimension on the projector: M4 with a maximum depth of 8 mm. Please design the stand such that the rear legs at the back of the projector do not contact the stand. The front legs can be turned and removed. 3. Horizontal adjustment mechanism (for example, bolts and nuts in four locations) 4. Please design the stand such that it does not topple over easily.
Page 167 6. Connecting to Other Equipment Reference drawings * The drawing showing the dimensional requirements is not an actual stand design drawing. [Side View] [Front View] Exhaust Screw holes for 4 - M4 use Intake air Tilt foot (remove) 130 or Rear foot Intake air greater** Horizontal adjuster ** Please refer to the previous page.
Page 168: Connecting To A Wired Lan
6. Connecting to Other Equipment Connecting to a Wired LAN The projector comes standard with a LAN port (RJ-45) which provides a LAN connection using a LAN cable. To use a LAN connection, you are required to set the LAN on the projector menu. Select [SETUP] → [NETWORK SETTINGS] → [WIRED LAN]. (→ page 124). Example of LAN connection Example of wired LAN connection Server LAN cable (not supplied) NOTE: Use a Category 5 or higher LAN cable.
Page 169: Maintenance
7. Maintenance WARNING • Please do not use a spray containing flammable gas to remove dust attached to the lens and cabinet. Doing so may result in fires. ❶ Cleaning the Lens • Turn off the projector before cleaning. • The projector has a plastic lens. Use a commercially available plastic lens cleaner. • Do not scratch or mar the lens surface as a plastic lens is easily scratched. • Never use alcohol or glass lens cleaner as doing so will cause damage to the plastic lens surface. ❷ Cleaning the Cabinet Turn off the projector, and unplug the projector before cleaning. • Use a dry soft cloth to wipe dust off the cabinet. If heavily soiled, use a mild detergent. • Never use strong detergents or solvents such as alcohol or thinner. • When cleaning the ventilation slits or the speaker using a vacuum cleaner, do not force the brush of the vacuum cleaner into the slits of the cabinet. Vacuum the dust off the ventilation slits. •...
Page 170: Appendix
8. Appendix ❶ Throw distance and screen size Three separate bayonet style lenses can be used on this projector. Refer to the information on this page and use a lens suited for the installation environment (screen size and throw distance). For instructions on mounting the lens, see page 138. Lens types and throw distance Screen size Lens model name NP40ZL NP41ZL NP42ZL (inches) (inches) (inches) (inches) 33 - 46 0.8 - 1.2 54 - 127 1.4 - 3.2 125 - 245 3.2 - 6.2 39 - 56 1.1 - 1.4...
Page 171: Tables Of Screen Sizes And Dimensions
8. Appendix Tables of screen sizes and dimensions Size (inches) Screen width Screen height (inches) (cm) (inches) (cm) 42.4 107.7 26.5 67.3 16:10 screen size (di- Screen 50.9 129.2 31.8 80.8 agonal) height 67.8 172.3 42.4 107.7 84.8 215.4 53.0 134.6 101.8 258.5 63.6 161.5 127.2...
Page 172 8. Appendix Example: When projecting on a 150" screen According to the tables of screen sizes and dimensions (→ page 153), H = 127.2" (323.1 cm), V = 79.5" (201.9 cm). Adjustment range in the vertical direction: The projected image can be moved upwards 0.5 × 79.5" (201.9 cm) ≈ 39.6" (101 cm), downwards 0.1 × 79.5" (201.9 cm) ≈ 8" (20 cm) (when the lens is at the center position). For a ceiling/front installation, the above figures are inverted. Adjustment range in the horizontal direction: The projected image can be moved to the left 0.2 × 127.2" (323.1 cm) ≈ 25.5" (64.5 cm), to the right 0.2 × 127.2" (323.1 cm) ≈ 25.5" (64.5 cm). * Figures differ by several % because the calculation is approximate.
Page 173: ❷ Compatible Input Signal List
8. Appendix ❷ Compatible Input Signal List HDMI/HDBaseT Signal Resolution ( dots ) Aspect Ratio Refresh Rate ( Hz ) 640 × 480 4 : 3 60/72/75/85/iMac SVGA 800 × 600 4 : 3 56/60/72/75/85/iMac 1024 × 768 4 : 3 60/70/75/85/iMac 1280 × 720 16 : 9 1280 ×...
Page 174 8. Appendix Analog RGB Signal Resolution ( dots ) Aspect Ratio Refresh Rate ( Hz ) 640 × 480 4 : 3 60/72/75/85/iMac SVGA 800 × 600 4 : 3 56/60/72/75/85/iMac 1024 × 768 4 : 3 60/70/75/85/iMac XGA+ 1152 × 864 4 : 3 1280 × 720 16 : 9 1280 ×...
Page 175 8. Appendix HDMI/HDBaseT 3D Signal Resolution ( dots ) Aspect Ratio Refresh Rate ( Hz ) 3D Format Frame Packing 23.98/24 Side By Side (Half) Top And Bottom Side By Side (Half) Top And Bottom Frame Packing 1920 × 1080p 29.97/30 Side By Side (Half) Top And Bottom Side By Side (Half) Top And Bottom Side By Side (Half) 59.94/60 Top And Bottom Side By Side (Half) Top And Bottom 1920 × 1080i Side By Side (Half) 16 : 9 59.94/60 Top And Bottom Frame Packing 23.98/24 Side By Side (Half) Top And Bottom Side By Side (Half) Top And Bottom Frame Packing...
Page 176: ❸ Specifications
8. Appendix ❸ Specifications 6780WUSS/6770UL/6765WUSS Model name Method Three primary color liquid crystal shutter projection method Specifications of main parts Liquid crystal Size 0.76" (with MLA) × 3 (aspect ratio: 16:10) panel Pixels 2,304,000 (1920 dots × 1200 lines) (*1) Projection lenses Refer to the specifications of option lens (→ 160 page) Light source Laser diode Optical device Integrator, Dichroic Mirror, XDP 6780WUSS:8000lm Light output ECO OFF (*2) (*3) 6765WUSS: 6500 lm Contrast ratio (all white/all black) 2500000:1 with dynamic contrast...
Page 177 8. Appendix 6780WUSS/6770UL/6765WUSS Model name DisplayPort Video input DisplayPort × 1 Data rate: 5.4 Gbps/2.7Gbps/1.62Gbps No. lanes: 1 lane/2 lanes/4 lanes Color depth: 8 bits, 10bits, 12bits Colorimetry: RGB, YCbCr444, YCbCr422, REC709, REC601 HDCP compatible (*4) Audio input DisplayPort: Sampling frequency – 32/44.1/48 kHz, Sampling bits – 16/20/24 bits PC control terminal D-Sub 9-pin × 1 USB port USB type A × 1 Ethernet/LAN/HDBaseT port RJ-45 × 1, Supports 10BASE-T/100BASE-TX Remote terminal Stereo mini jack × 1 3D SYNC output terminal 5 V / 10 mA, synchronized signal output for 3D use Usage environment Operating temperature: 41 to 104°F (5 to 40°C) (*5) Operating humidity: 20 to 80% (with no condensation) Storage temperature: 14 to 122°F (-10 to 50°C) Storage humidity: 20 to 80% (with no condensation) Operating altitude: 0 to 3650 m/12000 feet...
Page 178 8. Appendix Option lens (sold separately) NP40ZL Throw ratio 0.79 - 1.11:1, F2.0 - 2.5, f = 13.3 - 18.6 mm NP41ZL Throw ratio 1.30 - 3.02:1, F1.7 - 2.0, f = 21.8 - 49.7 mm NP42ZL Throw ratio 2.88 - 5.72:1, F2.2 - 2.6, f = 49.7 - 99.8 mm NOTE: • The above throw ratio is for projecting on 100" screen.
Page 179: ❹ Cabinet Dimensions
8. Appendix ❹ Cabinet Dimensions Unit: mm (inch) 580 (22.8) Lens center Lens center 250 (9.8)
Page 180: ❺ Pin Assignments And Signal Names Of Main Connectors
8. Appendix ❺ Pin assignments and signal names of main connectors COMPUTER IN/ Component Input Connector (Mini D-Sub 15 Pin) Connection and signal level of each pin Pin No. RGB Signal (Analog) YCbCr Signal 11 12 13 14 15 Green or Sync on Green Blue Ground Signal Level Ground Red Ground Cr Ground Video signal : 0.7Vp-p (Analog) Green Ground Y Ground Sync signal : TTL level Blue Ground...
Page 181 8. Appendix HDBaseT IN/Ethernet Port (RJ-45) Pin No. Signal TxD+/HDBT0+ TxD−/HDBT0− RxD+/HDBT1+ Disconnection/HDBT2+ Disconnection/HDBT2− RxD−/HDBT1− Disconnection/HDBT3+ Disconnection/HDBT3− USB-A Port (Type A) Pin No. Signal D− Grounding PC CONTROL Port (D-Sub 9 Pin) Pin No. Signal Unused RxD reception data TxD transmission data Unused Grounding Unused...
Page 182: ❻ Changing The Background Logo (Virtual Remote Tool)
8. Appendix ❻ Changing the Background Logo (Virtual Remote Tool) This will help you perform operations such as projector’s power on or off and signal selection via a LAN connection. It is also used to send an image to the projector and register it as the logo data of the projector. After registering it, you can lock the logo to prevent it from changing. Control Functions Power On/Off, signal selection, picture freeze, picture mute, audio mute, Logo transfer to the projector, and remote control operation on your PC. Virtual Remote screen Use this button for changing the background logo. Remote Control Window Toolbar For getting the Virtual Remote Tool, please visit our web site and download it: http://www.dukaneav.com NOTE: • Remote Control Window is not available for changing the background logo. Please see the HELP menu of the Virtual Remote Tool about how to display the Toolbar. • Logo data (graphics) that can be sent to the projector with Virtual Remote Tool has the following restrictions: (Only via serial or LAN connection) * File size: Within 256 kilobytes * Image size: Within the resolution of the projector * File format: PNG (Full color) •...
Page 183: ❼ Troubleshooting
8. Appendix ❼ Troubleshooting This section helps you resolve problems you may encounter while setting up or using the projector. Feature of each indicator ① POWER indicator This indicator informs the power status of the projector. ② STATUS indicator This indicator lights/blinks when a button is pressed while the CONTROL PANEL LOCK function is utilized, or while performing the lens calibration and specific operations. ③ LIGHT indicator This indicator informs the state of light source, used time of the light source, and the status of LIGHT MODE. ④ TEMP. indicator This is the temperature indicator informing temperature trouble when the ambient temperature is too high/low. Indicator Message (Status message) POWER STATUS LIGHT...
Page 184 8. Appendix POWER STATUS LIGHT TEMP. Projector status Lens calibration implement request. Status Orange Status varies (Blink* varies Performing the lens calibration Blue Green Status (Light) (Blink* varies Shutter function is activating Blue Status (Light) varies OFF Timer is activated, OFF time as the proogram timer is activated (Powered state) Blue Status (Blink* varies Preparing for powering ON Blue (Blink* *1 Repetition to light on for 1.5 seconds / off for 1.5 seconds *2 Repetition to light on for 1.5 seconds / off for 7.5 seconds *3 Repetition to light on for 2.5 seconds / off for 0.5 seconds *4 Repetition to light on for 0.5 seconds / off for 0.5 seconds / on for 0.5 seconds / off for 2.5 seconds *5 Repetition to light on for 0.5 seconds / off for 0.5 seconds...
Page 185: Indicator Message (Error Message)
8. Appendix Indicator Message (Error message) POWER STATUS LIGHT TEMP. Projector status Procedure A button has been pressed while the The projector’s keys are locked. The KEY LOCK is activated. setting must be canceled to operate Blue Orange Status the projector. (→ page 120) (Light) (Light) varies ID numbers for the projector and the Check the control IDs (→ page 121) remote control do not match. Temperature problem (In the Forced Ambient temteprature is high. Lower ECO) the room temperature.
Page 186: Explanation On The Power Indicator And Standby State
8. Appendix Explanation on the POWER indicator and standby state In the state the selected PROFILE for WIRED LAN is available. Available ports in each state (○: Available, ×: Unavailable) HDBaseT IN/ PC CON- Ethernet TROL HDBaseT OUT/ Ethernet Power consumption Power On High Indicator : Lights in blue Power On Powered ON state ○...
Page 187 8. Appendix In the state the selected PROFILE for WIRED LAN is unavailable. Available ports in each state (○: Available, ×: Unavailable) HDBaseT IN/ PC CONTROL Ethernet HDBaseT OUT/ Ethernet Power consumption Power On High Indicator: Lights in blue Powered ON state ○ × ○ Power Off Power On Indicator: Lights in green ○...
Page 188: Common Problems & Solutions
8. Appendix Common Problems & Solutions (→ “Indicator Message” on page 165.) Problem Check These Items Does not turn on • Check that the power cord is plugged in and that the power button on the projector cabinet or the remote control or shut down is on� (→ pages 14, 16) • Check to see if the projector has temperature error, If projector inside temperature is too hot or cool, it disabled to turn on the projector as the protection� Wait for a moment and try turn on the projector again� • Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1700 meters or higher�...
Page 189 8. Appendix Problem Check These Items Indicator is lit or • See the Indicator Message. (→ page 165) blinking Cross color in RGB • Press the AUTO ADJ. button on the projector cabinet or the remote control. (→ page 27) mode • Adjust the computer image manually with [CLOCK]/[PHASE] in [IMAGE OPTIONS] in the menu. (→ page 90) For more information contact your dealer.
Page 190: If There Is No Picture, Or The Picture Is Not Displayed Correctly
8. Appendix If there is no picture, or the picture is not displayed correctly. • Power on process for the projector and the PC. Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on the power to the notebook PC. In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up. NOTE: You can check the horizontal frequency of the current signal in the projector’s menu under Information. If it reads “0kHz”, this means there is no signal being output from the computer. (→ page 134 or go to next step) • Enabling the computer’s external display. Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector. When using a PC compatible laptop, a combination of function keys will enable/disable the external display. Usu- ally, the combination of the “Fn” key along with one of the 12 function keys gets the external display to come on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through external display selections. • Non-standard signal output from the computer If the output signal from a notebook PC is not an industry standard, the projected image may not be displayed correctly. Should this happen, deactivate the notebook PC’s LCD screen when the projector display is in use. Each notebook PC has a different way of deactivate/reactivate the local LCD screens as described in the previous step. Refer to your computer’s documentation for detailed information. • Image displayed is incorrect when using a Mac When using a Mac with the projector, set the DIPswitch of the Mac adapter (not supplied with the projector) ac- cording to your resolution. After setting, restart your Mac for the changes to take affect. For setting display modes other than those supported by your Mac and the projector, changing the DIP switch on a Mac adapter may bounce an image slightly or may display nothing. Should this happen, set the DIP switch to the 13" fixed mode and then restart your Mac. After that, restore the DIP switches to a displayable mode and then restart the Mac again.
Page 191: ❽ Pc Control Codes And Cable Connection
8. Appendix ❽ PC Control Codes and Cable Connection PC Control Codes Function Code Data POWER ON POWER OFF INPUT SELECT HDMI1 INPUT SELECT HDMI2 INPUT SELECT DisplayPort INPUT SELECT COMPUTER INPUT SELECT HDBaseT PICTURE MUTE ON PICTURE MUTE OFF SOUND MUTE ON SOUND MUTE OFF NOTE: Contact your local dealer for a full list of the PC Control Codes if needed.
Page 192: About The Ascii Control Command
8. Appendix ABOUT THE ASCII CONTROL COMMAND This device supports the common ASCII Control Command for controlling our projector and monitor. Please visit our web site for detailed information about the command. http://www.nec-display.com/dl/en/pj_manual/lineup.html HOW TO CONNECT WITH AN EXTERNAL DEVICE There are two methods to connect the projector with an external device such as a computer. 1. Connection thru the serial port. Connects the projector to a computer by a serial cable (a cross cable). 2. Connection via network (LAN/HDBaseT) Connects the projector to a computer by a LAN cable. Concerning to the type of LAN cable, please ask to your network administrator. CONNECTION INTERFACE 1. Connection thru the serial port. Communication Protocol Item Information Baud rate 115200/38400/19200/9600/4800 bps Data length 8 bits Parity bit No parity...
Page 193 8. Appendix Status command Response Error Status error:temp Temperature error error:fan Fan trouble error:light Light source trouble error:lens Lens trouble error:system System trouble...
Page 194: ❾ Troubleshooting Check List
8. Appendix ❾ Troubleshooting Check List Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by referring to the “Troubleshooting” section in your user’s manual. This checklist below will help us solve your problem more efficiently. * Print this page and the next page for your check. Frequency of occurrence □ always □ sometimes (How often?_____________________) □ other (__________________) Power □ No power (POWER indicator does not light blue)� See also “Status □ Shut down during operation� Indicator (STATUS)”� □ Power cord’s plug is fully inserted into the wall outlet� □ Power cord’s plug is fully inserted into the wall outlet�...
Page 195 8. Appendix In the space below please describe your problem in detail. Information on application and environment where your projector is used Projector Signal cable Model number: Standard or other manufacturer’s cable? Serial No�: Model number: Length: inch/m Date of purchase: Distribution amplifier Light operating time (hours): Model number: LIGHT MODE: □...
Page 196: ❿ Register Your Projector
❿ REGISTER YOUR PROJECTOR! (for residents in the United States, Canada, and Mexico) Please take time to register your new projector. Visit our web site at www.dukaneav.com and click on support to register. Upon receipt, we will send a confirmation letter with all the details you will need to take advantage of fast, reliable warranty and service programs from the industry leader, NEC Display Solutions of America, Inc. DUKANE CORP AV SERVICE DEPT 2900 Dukane Drive St Charles, IL 60174 800-676-2487 / 630-762-4032 Fax 630-584-5156 avservice@dukane.com...
Page 197 DUKANE CORP AV SERVICE DEPT 2900 Dukane Drive St Charles, IL 60174 800-676-2487 / 630-762-4032 Fax 630-584-5156 avservice@dukane.com www.dukaneav.com 430-6765WUSS-6770UL-6780WUSS_User Manual rev00...

This manual is also suitable for:

6765wuss 6780wuss 6770ul-l

Dukane 6770UL User Manual

Quick Links

Troubleshooting

Related Manuals for Dukane 6770UL

Summary of Contents for Dukane 6770UL

This manual is also suitable for:

Table of Contents