Related Manuals for Cobalt Digital Inc 9910DA-WC
Summary of Contents for Cobalt Digital Inc 9910DA-WC
- Page 1 9910DA-WC 9910DA-WC Audio Word Clock Distribution Amplifier Product Manual Cobalt Digital Inc. 2506 Galen Drive Champaign, IL 61821 Voice 217.344.1243 • Fax 217.344.1245 www.cobaltdigital.com 9910DA-WC-OM (V1.2)
- Page 2 Furthermore, Cobalt Digital Inc. reserves the right to make changes to any products herein to improve readability, function, or design. Cobalt Digital Inc. does not assume any liability arising out of the application or use of any product or circuit described herein.
-
Page 3: Table Of Contents
Operating Instructions........Overview ........................ 3-1 Accessing the 9910DA-WC Card via Remote Control .......... 3-1 Accessing the 9910DA-WC Card Using DashBoard™ ......3-1 Checking 9910DA-WC Card Information and Status .......... - Page 4 This page intentionally blank 9910DA-WC PRODUCT MANUAL 9910DA-WC-OM (V1.2)
-
Page 5: Chapter 1 Introduction
Also provides general information regarding the card. Chapter 2, “Installation and Setup” – Provides instructions for • installing the card in a frame, and optionally installing a 9910DA-WC Rear I/O Module. Chapter 3, “Operating Instructions” – Provides overviews of •... -
Page 6: Manual Conventions
Manual Conventions Manual Conventions In this manual, display messages and connectors are shown using the exact name shown on the 9910DA-WC itself (for example, connector names are shown like this: ANLG IN) In this manual, the terms below are applicable as follows: 9910DA-WC refers to the 9910DA-WC Audio Word Clock •... -
Page 7: Safety And Regulatory Summary
United States of America FCC "Code of Federal Regulations" Title 47 Part 15, Subpart B, Class A Canada ICES-003 International/CE CISPR 24:2010 IEC 61000-4-2:2008 IEC 61000-4-3:2006 with A1:2007 and A2:2010 IEC 61000-4-4:2004 IEC 61000-4-6:2008 CISPR 22:2008 9910DA-WC-OM (V1.2) 9910DA-WC PRODUCT MANUAL... -
Page 8: 9910Da-Wc Functional Description
9910DA-WC Functional Description 9910DA-WC Functional Description Figure 1-1 shows a functional block diagram of the 9910DA-WC. With the appropriate rear module, the 9910DA-WC can provide up to eight DA word clock outputs and a looping input where desired. 9910DA-WC Input/Output Formats... -
Page 9: 9910Da-Wc Rear I/O Modules
The 9910DA-WC physically interfaces to system audio connections at the rear of its frame using a Rear I/O Module. The full assortment of 9910DA-WC Rear I/O Modules is shown and described in 9910DA-WC Rear I/O Modules in Chapter 2, “Installation and Setup”. -
Page 10: Warranty And Service Information
(1) year. Cobalt Digital Inc.'s (“Cobalt”) sole obligation under this warranty shall be limited to, at its option, (i) the repair or (ii) replacement of the product, and the determination of whether a defect is covered under this limited warranty shall be made at the sole discretion of Cobalt. -
Page 11: Contact Cobalt Digital Inc
Introduction Contact Cobalt Digital Inc. Contact Cobalt Digital Inc. Feel free to contact our thorough and professional support representatives for any of the following: Name and address of your local dealer • Product information and pricing • Technical support •... - Page 12 This page intentionally blank 9910DA-WC PRODUCT MANUAL 9910DA-WC-OM (V1.2)
-
Page 13: Chapter 2 Installation And Setup
Installation and Setup Chapter 2 Overview This chapter contains the following information: Setting Card Jumpers (p. 2-1) • Installing the 9910DA-WC Into a Frame Slot (p. 2-2) • Installing a Rear I/O Module (p. 2-4) • Setting Card Jumpers CAUTION... -
Page 14: Installing The 9910Da-Wc Into A Frame Slot
Note: If installing the 9910DA-WC in a slot with no rear I/O module, a Rear I/O Module is required before cabling can be connected. Refer to Installing a Rear I/O Module (p. 2-4) for rear I/O module installation procedure. - Page 15 Verify that the card is fully engaged in rear I/O module mating connector. Close the frame front access panel. Connect the input and output cables as shown in 9910DA-WC Rear I/O Modules (p. 2-5). Repeat steps 1 through 8 for other 9910DA-WC cards.
-
Page 16: Installing A Rear I/O Module
This procedure is applicable only if a Rear I/O Module is not currently installed in the slot where the 9910DA-WC is to be installed. If installing the 9910DA-WC in a slot already equipped with a suitable I/O module, omit this procedure. -
Page 17: 9910Da-Wc Rear I/O Modules
Installation and Setup Installing a Rear I/O Module 9910DA-WC Rear I/O Modules Table 2-2 shows and describes the full assortment of Rear I/O Modules specifically for use with the 9910DA-WC. Table 2-2 9910DA-WC Rear I/O Modules 9910DA-WC Rear I/O Module... - Page 18 Installing a Rear I/O Module Table 2-2 9910DA-WC Rear I/O Modules — continued 9910DA-WC Rear I/O Module Description RM20-9910WC-B/S Split Rear Module. Provides each of the following connections for two 9910DA-WC cards: • Word clock input (WC IN) • One input looping output (LOOP) •...
-
Page 19: Chapter 3 Operating Instructions
Troubleshooting (p. 3-3) • Accessing the 9910DA-WC Card via Remote Control ® The 9910DA-WC card can be remote monitored via DashBoard™ or Cobalt Remote Control Panel. Access the 9910DA-WC card using DashBoard™ or ® Cobalt Remote Control Panel as described below. -
Page 20: Checking 9910Da-Wc Card Information And Status
Click on the card to be accessed (in this example, “Slot 6: 9910DA-WC”). Checking 9910DA-WC Card Information and Status The operating status of the 9910DA-WC card can be checked using DashBoard™. Figure 3-1 shows and describes the 9910DA-WC card information screen using DashBoard™. -
Page 21: Card-Edge Indicators
Item Checks Verify power presence and • On both the frame Network Controller Card and the 9910DA-WC, in all characteristics cases when power is being properly supplied there is always at least one indicator illuminated. Any card showing no illuminated indicators should be cause for concern. -
Page 22: Troubleshooting Network/Remote Control Errors
The Cobalt Digital Inc. Technical Support Department will continue to provide advice on any product manufactured by Cobalt Digital Inc., beyond the warranty period without charge, for the life of the product. See Contact Cobalt Digital Inc. (p. 1-7) in Chapter 1, “Introduction“ for contact information. 9910DA-WC PRODUCT MANUAL... - Page 24 Cobalt Digital Inc. 2506 Galen Drive Champaign, IL 61821 Voice 217.344.1243 • Fax 217.344.1245 www.cobaltdigital.com 9910DA-WC-OM (V1.2) Printed in USA...
Need help?
Do you have a question about the 9910DA-WC and is the answer not in the manual?
Questions and answers