3g/hd/sd-sdi/asi/madi reconfigurable video sfp transceiver/distribution amplifier with full-flexibility crosspoint and externally-accessible sfp module (36 pages)
Page 1
Cobalt Digital Inc. 9006 Triple 3G/HD/SD SDI Distribution Amplifier Owner’s Manual 9006-OM Version: 1.4...
Page 2
The material in this manual is furnished for informational use only. It is subject to change without notice and should not be construed as a commitment by Cobalt Digital Inc. Cobalt Digital Inc assumes no responsibility or liability for errors or inaccuracies that may appear in this manual.
To reduce the risk of fire, replacement fuses must be the same type and rating. Only use attachments/accessories specified by the manufacturer. 9006 Owner’s Manual • • • • (V 1.4) Page 3...
Page 4
If you need more information on the collection, reuse, and recycling systems, please contact your local or regional waste administration. You can also contact Cobalt Digital for more information on the environmental performances of our products. 9006 Owner’s Manual • • • • (V 1.4) Page 4...
Warranty and Repair Policy..................... 16 Ordering Information 9006 and Related Products ...................... 18 Contact Us Contact Cobalt Digital Inc....................... 19 Visit us at the Cobalt Digital Inc. website................19 9006 Owner’s Manual • • • • (V 1.4) Page 5...
The 9006 is a high quality three channel 3G/HD/SD Distribution Amplifier. It is capable of equalizing and equalizing three channels in 3G, HD or SD. The 9006 can equalize incoming SDI signals using up to 300m of cable at 270 Mbps, up to 120m of cable at 1.485 Gbps, and up to 80m at 2.97Gbps.
• “Operator” and “User” both refer to the person who uses the 9006. • “Board” and “Card” all refer to the 9006 card itself, including all components and switches. • “System” and “Video system” refers to the mix of interconnected production and terminal equipment in which the 9006 operates.
Unpack each card you received from the shipping container, and check the contents against the packing list to ensure that all items are included. If any items are missing or damaged, contact your sales representative or Cobalt Digital directly. 9006 Owner’s Manual • • • • (V 1.4) Page 8...
Using a Phillips driver and the supplied screw, fasten the rear module panel to the frame back plane. Do not over tighten. This completes the procedure for installing the rear module in a frame. 9006 Owner’s Manual • • • • (V 1.4) Page 9...
Then, fully insert the card into the frame until the rear connection plugs are properly seated on the midplane and rear modules. This completes the procedure for installing the card in the frame. 9006 Owner’s Manual • • • • (V 1.4) Page 10...
This section provides instructions for connecting cables to the installed BNC rear modules on the frame backplane. Connect the input and output cables according to the following diagram. Split rear module RM20-9006-B/S allow two cards to be installed in adjacent slots. B/S versions are available in DIN1.0/2/3 and HDBNC versions.
With switch 1 set in the down position, Dashboard remote control software is prevented from making changes to the card settings. Consequently the onboard switches 2-4 control the settings. The factory default setting has remote control disabled. 9006 Owner’s Manual • • • • (V 1.4) Page 12...
Using the Menus You must first install the DashBoard Control System software on your computer. Refer to the DashBoard User Manual for software installation procedures and for using the DashBoard interface. 9006 Owner’s Manual • • • • (V 1.4) Page 13...
Input Voltage rail Describes the current Lock Status A input rate Describes the current Lock Status Lock Status B input rate Describes the current Lock Status C input rate 9006 Owner’s Manual • • • • (V 1.4) Page 14...
Module Exchange Exchanging a suspect module with a module that is known to be working correctly is an efficient method for localizing problems to indivitriple modules. 9006 Owner’s Manual • • • • (V 1.4) Page 15...
(1) year. Cobalt Digital Inc.'s (“Cobalt”) sole obligation under this warranty shall be limited to, at its option, (i) the repair or (ii) replacement of the product, and the determination of whether a defect is covered under this limited warranty shall be made at the sole discretion of Cobalt.
Page 17
If required, a temporary replacement module will be made available at a nominal charge. Any shipping costs incurred will be the responsibility of you, the customer. All products shipped to you from Cobalt Digital Inc. will be shipped collect.
Ordering Information 9006 and Related Products Your 9006 Triple 3G/HD/SD SDI Distribution Amplifier is a part of the openGear family of products. Cobalt Digital offers a full line of openGear terminal equipment including distribution, conversion, monitoring, synchronizers, encoders, decoders, embedders, and de-embedders, as well as analog audio and video products.
Visit us at the Cobalt Digital Inc. website. http://www.cobaltdigital.com • Online catalog • Related products and full product lines • Trade show information • Dealer information • Cobalt Digital Inc. news 9006 Owner’s Manual • • • • (V 1.4) Page 19...