Fitting The Accessories - Black & Decker BDCINF18 Manual

ENGLISH
5. Pressure Mode / Reset Button
6. Handle
7. High-volume hose
8. Tapered nozzle
9. Universal valve adapter
10 . High-pressure hose
11. High-volume pump deflate connection
12. High volume pump inflator connection
13. 230V AC cord
14. 12V DC vehicle connector
15. 18V MAX* battery slot
16. Inflator needle valve
17. Brass coupler adapter
18. Tapered nozzle
Assembly
12V DC Cord Storage
Wrap the 12V DC cord around the cord retainer located
u
in the base of the inflator and snap the 12V DC connector
(14) into its storage location on the cord retainer.
Air Hose Storage
The high-pressure hose (10) is located in a storage chan-
u
nel around the face of the unit. Wrap the highpressure
hose inside the channel.
High-Volume Hose Storage
The high-volume hose (7) is located in a storage channel
u
around the back of the unit. Wrap the high-volume hose
inside the channel.
Accessories Storage
The accessories (16) (17) (18) are stored in the back of
u
the unit inside the accessory storage area.

Fitting the accessories

Universal valve adapter (Fig. A)
Your inflator is supplied with the standard tapered nozzle
u
(18) , a brass coupler (17) , and the inflator needle valve
(16) , located on the back of the unit.
To use the universal valve adaptor (9) , make sure the
u
lever is in the up position.
Place the valve adapter over the stem of the inflator
u
needle valve, brass coupler adaptor or tapered nozzle.
Press the lever (19) on the universal valve adapter down
u
to lock it in place.
Place the inflator needle valve, brass coupler adapter or
u
tapered nozzle into the item to be inflated.
Note: Always make sure that the lever is in the up position
when not in use. Operate your inflator only with the universal
valve adaptor or with the included nozzles.
6
(Original instructions)
Note: Make sure the universal valve adapter is firmly locked in
place before turning the inflator on.
High-volume hose (Fig. B)
Remove the high-volume hose 7 from the storage location.
u
Line up the notches 20 of the hose with the nubs (21) of
u
the high volume pump inflator connection (12) . Then,
slide the hose on and twist counter-clockwise to secure.
To remove, twist the hose clockwise and slide hose off.
u
Note: Many inflatables have an internal flap that prevents air
loss during inflation, especially air mattresses. Unless this flap
is displaced by the nozzle the inflatable will not inflate. Push
the nozzle firmly into the valve to make sure that you push
this flap out of the way.
Warning! Risk of Bursting. Excessive air pressure may cause
a hazardous risk of bursting or personal injury. Check the
manufacturer's maximum pressure rating for items being
inflated.
Note: If the pressure rating for the item being inflated
is above 100 psi, note that the maximum run time is 10
minutes, leave to rest for 20 minutes before reusing.
Operation
Warning! To reduce the risk of serious personal injury, turn
unit off and disconnect it from power source and remove the
battery pack before making any adjustments or removing/
installing attachments or accessories. An accidental start-up
can cause injury.
Warning! Do not operate the inflator when the car
engine is running.
Note: Make sure that your 12 Volt accessory socket is live.
On some vehicles the accessory socket may only become
live when the ignition key is in the accessory position.
Installing and Removing the Battery Pack
(Fig. C, D)
Note: For best results, make sure your battery pack is
fully charged.
To install the battery pack into the battery port (15) , align
u
the battery pack with the rails inside the battery port and
slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the
u
release button (22) and firmly pull the battery pack out of
the tool handle. Insert it into the charger as described in
the charger section of this manual.
Switching On (Fig. E, F)
Warning! Risk of Bursting. Do not leave unit running unat-
tended. Overinflation of tires and other items could result in
serious injury and property damage.
Note: When power is supplied to the inflator by 12v, 20v
battery, or 230V AC the LCD display will remain on for
approximately 10 minutes before the display shuts off/goes
into sleep mode.