Supermicro X11DPT-L User Manual
  1. Manuals
  2. Brands
  3. Supermicro Manuals
  4. Motherboard
  5. X11DPT-L
  6. User manual
Supermicro X11DPT-L User Manual

Supermicro X11DPT-L User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
X11DPT-L
USER'S MANUAL
Revision 1.0b

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the X11DPT-L and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Supermicro X11DPT-L

Summary of Contents for Supermicro X11DPT-L

  • Page 1 X11DPT-L USER’S MANUAL Revision 1.0b...
  • Page 2 State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product.
  • Page 3 About This Manual This manual is written for system integrators, IT technicians, and knowledgeable end users. It provides information for the installation and use of the X11DPT-L motherboard. About This Motherboard The X11DPT-L motherboard supports dual Intel® Xeon® Scalable-SP series and 2nd Gen Intel Xeon Scalable-SP series processors in Socket P type with a TDP (Thermal Design Power) of up to 140W and two UPI (Ultra Path Interconnect) links of up to 10.4 GT/s.
  • Page 4 Contacting Supermicro Contacting Supermicro Headquarters Address: Super Micro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Website: www.supermicro.com Europe Address: Super Micro Computer B.V.

  • Page 5: Table Of Contents

    Table of Contents Table of Contents Chapter 1 Introduction 1.1 Overview ..........................8 1.2 Processor and Chipset Overview ..................16 1.3 Special Features ........................17 1.4 System Health Monitoring ....................17 1.5 ACPI Features ........................18 1.6 Power Supply ........................18 1.7 Advanced Power Management ..................18 Chapter 2 Installation 2.1 Static-Sensitive Devices .....................20 Precautions ........................20...
  • Page 6 Super X11DPT-L User's Manual Memory Support ........................31 General Memory Population Requirements ..............31 DDR4 Memory Support for Intel Xeon Scalable-SP Processors ........32 DDR4 Memory Support for 2nd Gen Intel Xeon Scalable-SP Processors .......32 DIMM Population Guidelines for Optimal Performance ............33 DIMM Population Table .....................34 DIMM Installation ......................35...
  • Page 7 Table of Contents Chapter 4 UEFI BIOS 4.1 Introduction .........................61 4.2 Main Setup .........................62 4.3 Advanced Setup Configurations ..................64 4.4 Event Logs .........................92 4.5 IPMI ........................... 94 4.6 Security ..........................97 4.7 Boot ..........................100 4.8 Save & Exit ........................103 Appendix A BIOS Codes A.1 BIOS Error POST (Beep) Codes ..................105 Appendix B Software B.1 Microsoft Windows OS Installation ...................107...

  • Page 8: Chapter 1 Introduction

    Chapter 1 Introduction Congratulations on purchasing your computer motherboard from an industry leader. Supermicro motherboards are designed to provide you with the highest standards in quality and performance. 1.1 Overview This motherboard was designed to be used with a Supermicro-proprietary chassis as an integrated server platform.
  • Page 9 Chapter 1: Introduction Figure 1-1. X11DPT-L Motherboard Image Note: All graphics shown in this manual were based upon the latest PCB revision available at the time of publication of the manual. The motherboard you received may or may not look exactly the same as the graphics shown in this manual.
  • Page 10 Super X11DPT-L User's Manual Figure 1-2. X11DPT-L Motherboard Layout (not drawn to scale) COM1 LAN2 LAN1 IPMI_LAN USB0/1(3.0) CTRL CTRL LEDM1 JSD1 JTPM1 I-SATA6 JBT1 SXB1 I-SATA7 JSD2 BIOS LICENSE CPU1 CPU2 Notes: • Chapter 2 for detailed information on jumpers, I/O ports, and JF1 front panel con- nections.
  • Page 11 Pins 1-2 (Enabled, Reset) Connector Description Onboard Battery COM1 Back Panel COM Port I-SATA Ports with Built-in Power Pins and with Support of Supermicro SuperDOM (Disk On I-SATA6/I-SATA7 Module) Devices IPMI_LAN Dedicated IPMI_LAN Port Front Panel Control Signals and Power Input Connector...
  • Page 12 Six (6) SATA 3.0 ports supported by Intel PCH (I-SATA0~5) ® • • SATA 3.0 Two (2) SATA 3.0 ports with power-pins built-in, w/support of Supermicro SuperDOM (I-SATA6/I-SATA7) • • RAID (PCH) RAID 0, 1, 5, and 10 Peripheral Devices •...
  • Page 13 Main switch override mechanism • Power-on mode for AC power recovery • Intel Intelligent Power Node Manager 4.0 (available when the Supermicro Power Manager [SPM] is installed and a ® special power supply is used) • Management Engine (ME) System Health Monitoring •...
  • Page 14 Note 1: The CPU maximum thermal design power (TDP) is subject to chassis and heatsink cooling restrictions. For proper thermal management, please check the chassis and heatsink specifications for proper CPU TDP sizing. Note 2: For IPMI configuration instructions, please refer to the Embedded IPMI Con- figuration User's Guide available at http://www.supermicro.com/support/manuals/.
  • Page 15 Chapter 1: Introduction Figure 1-3. C621 System Block Diagram VCCP0 VCCP1 VR13 VR13 4+1 PHASE 4+1 PHASE VPP_AB (2.575) 140W 140W VDDQ_AB (1.2) 10.4 GT VTT_M_AB (0.6) CPU 1 CPU 2 DMI3 DMI3 SLOT1 PCI-E x16 G3 SXB2 PCI-E x4 G3 UPLINK DMI3 #0~#5...

  • Page 16: Processor And Chipset Overview

    Super X11DPT-L User's Manual 1.2 Processor and Chipset Overview Built upon the functionality and capability of Intel Xeon Scalable-SP and 2nd Generation Intel Xeon Scalable-SP processors (Socket P) and the C621 chipset, this motherboard provides superb system performance, efficient power management, and a rich feature set based on cutting edge technology to address the needs of next-generation computer users.

  • Page 17: Special Features

    Chapter 1: Introduction 1.3 Special Features This section describes the health monitoring features of the X11DPT-L motherboard. The motherboard has an onboard ASPEED AST2500 Baseboard Management Controller (BMC) that supports system health monitoring. Recovery from AC Power Loss The Basic I/O System (BIOS) provides a setting that determines how the system will respond when AC power is lost and then restored to the system.

  • Page 18: Acpi Features

    Super X11DPT-L User's Manual System Resource Alert This feature is available when used with SuperDoctor 5. SuperDoctor 5 is used to notify the ® ® user of certain system events. For example, you can configure SuperDoctor 5 to provide you ®...
  • Page 19 Chapter 1: Introduction Management Engine (ME) The Management Engine, which is an ARC controller embedded in the IOH (I/O Hub), provides Server Platform Services (SPS) to your system. The services provided by SPS are different from those provided by the ME on client platforms.

  • Page 20: Chapter 2 Installation

    Super X11DPT-L User's Manual Chapter 2 Installation 2.1 Static-Sensitive Devices Electrostatic Discharge (ESD) can damage electronic com ponents. To avoid damaging your motherboard and your system, it is important to handle it very carefully. The following measures are generally sufficient to protect your equipment from ESD.

  • Page 21: Motherboard Installation

    Chapter 2: Installation 2.2 Motherboard Installation All motherboards have standard mounting holes to fit different types of chassis. Make sure that the locations of all the mounting holes for both the motherboard and the chassis match. Although a chassis may have both plastic and metal mounting fasteners, metal ones are highly recommended because they ground the motherboard to the chassis.

  • Page 22: Installing The Motherboard

    Super X11DPT-L User's Manual Installing the Motherboard 1. Install the I/O shield into the back of the chassis. 2. Locate the mounting holes on the motherboard. See the previous page for the location. 3. Locate the matching mounting holes on the chassis. Align the mounting holes on the motherboard against the mounting holes on the chassis.

  • Page 23: Processor And Heatsink Installation

    CPU socket cap is in place and that none of the socket pins are bent; otherwise, contact your retailer immediately. • Refer to the Supermicro website for updates on CPU support. • Please follow the instructions given in the ESD Warning section on the first page of this chapter before handling, installing, or removing system components.

  • Page 24: Overview Of The Processor Socket Assembly

    Super X11DPT-L User's Manual Overview of the Processor Socket Assembly The processor socket assembly contains 1) Intel Xeon Scalable-SP or 2nd Generation Intel Xeon Scalable-SP processor, 2) the narrow processor clip, 3) the dust cover, and 4) the CPU socket.

  • Page 25: Overview Of The Processor Heatsink Module (Phm)

    Chapter 2: Installation Overview of the Processor Heatsink Module (PHM) The Processor Heatsink Module (PHM) contains 1) a heatsink, 2) a narrow processor clip, and 3) Intel Xeon Scalable-SP or 2nd Generation Intel Xeon Scalable-SP processor. 1. Heatsink 2. Narrow processor clip 3.

  • Page 26: Attaching The Processor To The Narrow Processor Clip To Create The Processor Package Assembly

    Super X11DPT-L User's Manual Attaching the Processor to the Narrow Processor Clip to Create the Processor Package Assembly To properly install the CPU into the narrow processor clip, please follow the steps below. 1. Locate pin 1 (notch A), which is the triangle located on the top of the narrow processor clip.

  • Page 27: Attaching The Processor Package Assembly To The Heatsink To Form The Processor Heatsink Module (Phm)

    Chapter 2: Installation Attaching the Processor Package Assembly to the Heatsink to Form the Processor Heatsink Module (PHM) After you have made a processor package assembly by following the instructions on the previous page, please follow the steps below to mount the processor package assembly onto the heatsink to create the Processor Heatsink Module (PHM).

  • Page 28: Preparing The Cpu Socket For Installation

    Super X11DPT-L User's Manual Preparing the CPU Socket for Installation This motherboard comes with the CPU socket pre-assembled in the factory. The CPU socket contains 1) a dust cover, 2) a socket bracket, 3) the CPU socket, and 4) a back plate. These components are pre-installed on the motherboard before shipping.

  • Page 29: Installing The Processor Heatsink Module (Phm)

    Chapter 2: Installation Installing the Processor Heatsink Module (PHM) 1. Once you have assembled the processor heatsink module (PHM) by following the instructions listed on page 30 or page 31, you are ready to install the processor heatsink module (PHM) into the CPU socket on the motherboard. To install the PHM into the CPU socket, follow the instructions below.

  • Page 30: Removing The Processor Heatsink Module (Phm) From The Motherboard

    Super X11DPT-L User's Manual Removing the Processor Heatsink Module (PHM) from the Motherboard Before removing the processor heatsink module (PHM), unplug power cord from the power outlet. 1. Using a T30 Torx-bit screwdriver, turn the screws on the PHM counterclockwise to loosen them from the socket, starting with screw marked #4 (in the sequence of 4, 3, 2, 2.

  • Page 31: Memory Support And Installation

    Chapter 2: Installation 2.4 Memory Support and Installation Notes: Check the Supermicro website for recommended memory modules. Exercise extreme care when installing or removing DIMM modules to prevent any damage. Memory Support The motherboard supports up to 2TB of 3DS Load Reduced DIMM (3DS LRDIMM), 3DS Registered DIMM (3DS RDIMM), or up to 1TB of Load Registered DIMM (LRDIMM), with speeds of 2933*/2666/2400/2133/1866/1600/1333 MHz modules in 8 memory slots.

  • Page 32: Ddr4 Memory Support For Intel Xeon Scalable-Sp Processors

    2933 Notes: 1. 2933 MHz memory support in two-DIMMs per-channel (2DPC) configuration can be achieved by using memory purchased from Supermicro. 2. Support for 2933MHz memory is dependent on the CPU SKU. 3. 16Gb-based memory modules are supported by 2nd Gen Intel Xeon Scalable-SP processors only.

  • Page 33: Dimm Population Guidelines For Optimal Performance

    Chapter 2: Installation DIMM Population Guidelines for Optimal Performance For optimal memory performance, follow the instructions listed in the tables below when populating memory modules. Key Parameters for DIMM Configuration Key Parameters for DIMM Configurations Parameters Possible Values Number of Channels 1, 2, 3, 4, 5, or 6 Number of DIMMs per Channel 1DPC (1 DIMM Per Channel)

  • Page 34: Dimm Population Table

    Super X11DPT-L User's Manual DIMM Population Table Note: Unbalanced memory configuration decreases memory performance and is not recommended for Supermicro motherboards. Memory Population Table for the Motherboard Using Intel Xeon Scalable-SP and 2nd Gen Intel Xeon Scalable-SP Processors Memory Population Table for the X11DP Motherboard w/8 DIMM Slots Onboard...

  • Page 35: Dimm Installation

    Chapter 2: Installation DIMM Installation COM1 LAN2 LAN1 IPMI_LAN 1. Insert DIMM modules in the following USB0/1(3.0) CTRL CTRL LEDM1 order: P1-DIMMA1, P1-DIMMD1, P1- JSD1 DIMMB1, and P1-DIMME1. For the system JTPM1 I-SATA6 JBT1 to work properly, please use memory SXB1 modules of the same type and speed on I-SATA7...

  • Page 36: Rear I/O Ports

    Super X11DPT-L User's Manual 2.5 Rear I/O Ports See the layout below for the locations and descriptions of the various I/O ports on the rear of the motherboard. LAN2 LAN1 IPMI_LAN COM1 USB0/1(3.0) CTRL CTRL LEDM1 JSD1 JTPM1 I-SATA6 JBT1...
  • Page 37 Chapter 2: Installation VGA Port The onboard VGA port is located on the I/O back panel. Use this connection for VGA display. Serial Port There is one COM port (COM1) on the I/O back panel. The COM port provides serial communication support.
  • Page 38 Super X11DPT-L User's Manual Universal Serial Bus (USB) Ports There are two USB 3.0 ports (USB0/USB1) on the I/O back panel. See the table below for pin definitions. Back Panel USB0 (3.0) Back Panel USB1 (3.0) Pin Definitions Pin Definitions...
  • Page 39 (Note: UID can also be triggered via IPMI on the motherboard. For more information, please refer to the IPMI User's Guide posted on our website at http://www.supermicro.com.) UID Switch...

  • Page 40: Connectors

    Super X11DPT-L User's Manual 2.6 Connectors Headers 4-pin BMC External I C Header A System Management Bus header for IPMI 2.0 is located at JIPMB1. Connect the appropriate cable here to use the IPMB I C connection on your system. Refer to the table below for pin definitions.
  • Page 41 Chapter 2: Installation TPM Header The JTPM1 header is used to connect a Trusted Platform Module (TPM)/Port 80, which is available from SMCI (optional). A TPM/Port 80 connector is a security device that supports encryption and authentication in hard drives. It allows the motherboard to deny access if the TPM associated with the hard drive is not installed in the system.
  • Page 42 Super X11DPT-L User's Manual Disk-On-Module Power Connector The Disk-On-Module (DOM) power connectors at JSD1 and JSD2 provide 5V power to a solid-state DOM storage devices connected to one of the SATA ports. See the table below for pin definitions. DOM Power...
  • Page 43 Chapter 2: Installation I-SATA 3.0 Ports The X11DPT-L has eight I-SATA 3.0 ports (I-SATA0 ~ I-SATA7) on the motherboard. These SATA ports are supported by the C621 chipset. I-SATA ports 0~5 are supported by SXB1. I-SATA6/I-SATA7 can be used with Supermicro SuperDOMs which are yellow SATA DOM connectors with power pins built in, and do not require external power cables.

  • Page 44: Jumper Settings

    Super X11DPT-L User's Manual 2.7 Jumper Settings How Jumpers Work To modify the operation of the motherboard, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector. Pin 1 is identified with a square solder pad on the printed circuit board. See the diagram at right for an example of jumping pins 1 and 2.
  • Page 45 Chapter 2: Installation CMOS Clear JBT1 is used to clear CMOS, which will also clear any passwords. Instead of pins, this jumper consists of contact pads to prevent accidentally clearing the contents of CMOS. To Clear CMOS 1. First power down the system and unplug the power cord(s). 2.
  • Page 46 Super X11DPT-L User's Manual Manufacturing Mode Select Close JPME2 to bypass SPI flash security and force the system to use the Manufacturing Mode, which will allow you to flash the system firmware from a host server to modify system settings. See the table below for jumper settings.
  • Page 47 Chapter 2: Installation Watch Dog JWD1 controls the Watch Dog function. Watch Dog is a monitor that can reboot the system when a software application hangs. Jumping pins 1-2 will cause Watch Dog to reset the system if an application hangs. Jumping pins 2-3 will generate a non-maskable interrupt signal for the application that hangs.

  • Page 48: Led Indicators

    Super X11DPT-L User's Manual 2.8 LED Indicators IPMI-Dedicated LAN LEDs An IPMI- dedicated LAN is located on the I/O back panel of the motherboard. The amber LED on the right indicates activity, while the green LED on the left indicates the speed of the connection.
  • Page 49 Chapter 2: Installation LAN1/LAN2 LEDs Two LAN ports (LAN1/LAN2) are located on the I/O back panel of the motherboard. Each Ethernet LAN port has two LEDs. The amber LED on the right indicates activity, while the other Link LED on the left may be orange or off to indicate the speed of the connection. See the tables below for more information.
  • Page 50 Super X11DPT-L User's Manual BMC Heartbeat LED LEDM1 is the BMC heartbeat LED. When the LED is blinking green, BMC is functioning normally. See the table below for the LED status. BMC Heartbeat LED Indicator LED Color Definition Green: BMC Normal Blinking 1.
  • Page 51 Chapter 2: Installation Unit ID LED A rear UID LED indicator at LE1 is located near the UID switch on the I/O back panel. This UID indicator provides easy identification of a system unit that may need service. UID LED Indicator LED Color Definition Blue: On...

  • Page 52: Chapter 3 Troubleshooting

    Super X11DPT-L User's Manual Chapter 3 Troubleshooting 3.1 Troubleshooting Procedures Use the following procedures to troubleshoot your system. If you have followed all of the procedures below and still need assistance, refer to the ‘Technical Support Procedures’ and/ or ‘Returning Merchandise for Service’ section(s) in this chapter. Always disconnect the AC power cord before adding, changing or installing any non hot-swap hardware components.

  • Page 53: No Video

    Chapter 3: Troubleshooting No Video 1. If the power is on but you have no video, remove all the add-on cards and cables. 2. Use the speaker to determine if any beep codes exist. Refer to Appendix A for details on beep codes.

  • Page 54: Losing The System's Setup Configuration

    Super X11DPT-L User's Manual Losing the System's Setup Configuration 1. Make sure that you are using a high quality power supply. A poor quality power supply may cause the system to lose the CMOS setup information. Refer to Section 1.6 details on recommended power supplies.
  • Page 55 Chapter 3: Troubleshooting 3. Using the minimum configuration for troubleshooting: Remove all unnecessary components (starting with add-on cards first), and use the minimum configuration (but with a CPU and a memory module installed) to identify the trouble areas. Refer to the steps listed in Section A above for proper troubleshooting procedures.

  • Page 56: Technical Support Procedures

    Super X11DPT-L User's Manual 3.2 Technical Support Procedures Before contacting Technical Support, please take the following steps. Also, note that as a motherboard manufacturer, we do not sell directly to end-users, so it is best to first check with your distributor or reseller for troubleshooting services. They should know of any possible problem(s) with the specific system configuration that was sold to you.

  • Page 57: Battery Removal And Installation

    Chapter 3: Troubleshooting 3.3 Battery Removal and Installation Battery Removal To remove the onboard battery, follow the steps below: 1. Power off your system and unplug your power cable. 2. Using a tool such as a pen or a small screwdriver, push the battery lock outwards to unlock it.

  • Page 58: Frequently Asked Questions

    3.4 Frequently Asked Questions Question: What type of memory does my motherboard support? Answer: The X11DPT-L motherboard supports up to 2TB of 3DS Load Reduced DIMM (3DS LRDIMM), 3DS Registered DIMM (3DS RDIMM), or up to 1TB of Load Registered DIMM (LRDIMM), with speeds of 2933*/2666/2400/2133/1866/1600/1333 MHz modules in eight memory slots.
  • Page 59 Chapter 3: Troubleshooting Question: How do I update my BIOS under UEFI Shell? Note: We do not recommend that you update your BIOS if you are not experiencing a BIOS-related problem. If you need to update your BIOS, please follow the steps below to properly update your BIOS under UEFI Shell.

  • Page 60: Returning Merchandise For Service

    Super X11DPT-L User's Manual 3.5 Returning Merchandise for Service A receipt or copy of your invoice marked with the date of purchase is required before any warranty service will be rendered. You can obtain service by calling your vendor for a Returned Merchandise Authorization (RMA) number.

  • Page 61: Chapter 4 Uefi Bios

    Chapter 4: UEFI BIOS Chapter 4 UEFI BIOS 4.1 Introduction This chapter describes the AMIBIOS™ Setup utility for the motherboard. The BIOS is stored on a chip and can be easily upgraded using a flash program. Note: Due to periodic changes to the BIOS, some settings may have been added or deleted and might not yet be recorded in this manual.

  • Page 62: Main Setup

    X11DPT-L User's Manual 4.2 Main Setup When you first enter the AMI BIOS setup utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab on the top of the screen. The Main BIOS setup screen is shown below.
  • Page 63 Chapter 4: UEFI BIOS CPLD Version This item displays the version of the CPLD (Complex-Programmable Logical Device) used in the system. Memory Information Total Memory This item displays the total size of memory available in the system.

  • Page 64: Advanced Setup Configurations

    X11DPT-L User's Manual 4.3 Advanced Setup Configurations Use the arrow keys to select Boot Setup and press <Enter> to access the submenu items. Warning: Take caution when changing the Advanced settings. An incorrect value, a very high DRAM frequency, or an incorrect DRAM timing setting may make the system unstable. When this occurs, revert to the default to the manufacture default settings.
  • Page 65 Chapter 4: UEFI BIOS Wait For "F1" If Error Use this feature to force the system to wait until the 'F1' key is pressed if an error occurs. The options are Disabled and Enabled. INT19 (Interrupt 19) Trap Response Interrupt 19 is the software interrupt that handles the boot disk function. When this item is set to Immediate, the ROM BIOS of the host adaptors will "capture"...
  • Page 66 X11DPT-L User's Manual Power Button Function This feature controls how the system shuts down when the power button is pressed. Select 4 Seconds Override for the user to power off the system after pressing and holding the power button for 4 seconds or longer. Select Instant Off to instantly power off the system as soon as the user presses the power button.
  • Page 67 Chapter 4: UEFI BIOS Cores Enabled Use this feature to enable or disable CPU cores in the processor specified by the user. The default setting is 0. Monitor/Mwait Streaming SIMD Extensions 3 (SSE3) includes Monitor and Mwait instructions, which are used for thread synchronization.
  • Page 68 X11DPT-L User's Manual LLC Prefetch If this feature is set to Enabled, the hardware prefetcher will prefetch streams of data and instructions from the main memory to the L3 cache to improve CPU performance. The options are Disable and Enable.
  • Page 69 Chapter 4: UEFI BIOS Degrade Precedence Use this feature to set degrade precedence when system settings are in conflict. Select Topology Precedence to degrade Features. Select Feature Precedence to degrade Topol- ogy. The options are Topology Precedence and Feature Precedence. Link L0p Enable Select Enable for Link L0p support.
  • Page 70 X11DPT-L User's Manual Isoc Mode Select Enabled for Isochronous support to meet QoS (Quality of Service) requirements. This feature is especially important for Virtualization Technology. The options are Disable, Enable, and Auto. Memory Configuration Integrated Memory Controller (IMC) Enforce POR Select Enable to enforce POR restrictions on DDR4 frequency and voltage programming.
  • Page 71 Chapter 4: UEFI BIOS Memory Topology This feature displays DIMM population information. P1 DIMMA1: 2666MT/S Micron SRx4 16GB RDIMM P1 DIMMB1: 2666MT/S Micron SRx4 16GB RDIMM P1 DIMMD1: 2666MT/S Micron SRx4 16GB RDIMM P1 DIMME1: 2666MT/S Micron SRx4 16GB RDIMM P2 DIMMA1: 2666MT/S Micron SRx4 16GB RDIMM P2 DIMMB1: 2666MT/S Micron SRx4 16GB RDIMM P2 DIMMD1: 2666MT/S Micron SRx4 16GB RDIMM...
  • Page 72 X11DPT-L User's Manual SDDC Plus One Single Device Data Correction (SDDC) organizes data in a single bundle (x4/x8 DRAM). If any or all the bits become corrupted, corrections occur. The x4 condition is corrected on all cases. The x8 condition is corrected only if the system is in Lockstep Mode. The options are Disable and Enable.
  • Page 73 Chapter 4: UEFI BIOS Link Speed Use this feature to select the link speed for the PCI-E port specified by the user. The options are Auto, Gen 1 (2.5 GT/s), Gen 2 (5 GT/s), and Gen 3 (8 GT/s). PCI-E Port Link Status This feature displays current PCI-E Link Status.
  • Page 74 X11DPT-L User's Manual IOAT Configuration Disable TPH Transparent Hugepages is a Linux memory management system that enables com- munication in larger blocks (pages). Enabling this feature will increase performance. The options are No and Yes. Prioritize TPH Use this feature to enable Prioritize TPH support. The options are Enable and Disable.
  • Page 75 Chapter 4: UEFI BIOS Intel® VMD Technology This section describes the configuration settings for the Intel® Volume Management Device (VMD) Technology. Note: After you’ve enabled VMD on a PCI-E slot of your choice, this PCI-E slot will be dedicated for VMD use only, and it will no longer support any PCI-E device. To re-activate this slot for PCI-E use, please disable VMD.
  • Page 76 X11DPT-L User's Manual VMD Config for PStack2 Intel® VMD for Volume Management Device Select Enable to use the Intel Volume Management Device Technology for this stack. The options are Disable and Enable. *If the feature "Intel VMD for Volume Management Device" is set to Enable, the following features will be available: CPU1 SLOT1 PCI-E 3.0 X4 (IN X8) VMD (Available when the device is...
  • Page 77 Chapter 4: UEFI BIOS South Bridge USB Module Version This feature display current USB module version. USB Devices This feature display current USB device. Legacy USB Support This feature enables support for USB 2.0 and older. The options are Enabled, Disabled, and Auto.
  • Page 78 X11DPT-L User's Manual PCH SATA Configuration When this submenu is selected, the AMI BIOS automatically detects the presence of the SATA devices that are supported by the Intel PCH chip and displays the following items: SATA Controller This item enables or disables the onboard SATA controller supported by the Intel PCH chip.
  • Page 79 Chapter 4: UEFI BIOS Port 0 ~ Port 7 Spin Up Device On an edge detect from 0 to 1, set this item to allow the PCH to initialize the device. The options are Disabled and Enabled. Port 0 ~ Port 7 SATA Device Type Use this item to specify if the SATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive.
  • Page 80 X11DPT-L User's Manual SR-IOV Support Use this feature to enable or disable Single Root IO Virtualization Support. The options are Disabled and Enabled. MMIO High Base Use this item to select the base memory size according to memory-address mapping for the IO hub.
  • Page 81 Chapter 4: UEFI BIOS RSC-T2R-884 SLOT2 PCI-E 3.0 X8 OPROM Use this feature to select which firmware type to be loaded for the add-on card in this slot. The options are Disabled, Legacy, and EFI. M.2-H OPROM Use this feature to select which firmware type to be loaded for the add-on card in this slot. The options are Disabled, Legacy, and EFI.
  • Page 82 X11DPT-L User's Manual IPv6 HTTP Support Select Enabled to enable IPv6 HTTP boot support. The options are Disabled and Enabled. PXE Boot Wait Time Use this option to specify the wait time to press the ESC key to abort the PXE boot. Press "+"...
  • Page 83 Chapter 4: UEFI BIOS Device Settings This item displays the status of a serial part specified by the user. Change Settings This feature specifies the base I/O port address and the Interrupt Request address of a serial port specified by the user. Select Auto to allow the BIOS to automatically assign the base I/O and IRQ address.
  • Page 84 X11DPT-L User's Manual Data Bits Use this feature to set the data transmission size for Console Redirection. The options are 7 Bits and 8 Bits. Parity A parity bit can be sent along with regular data bits to detect data transmission errors. Select Even if the parity bit is set to 0, and the number of 1's in data bits is even.
  • Page 85 Chapter 4: UEFI BIOS Redirection After BIOS POST Use this feature to enable or disable legacy console redirection after BIOS POST. When set to Bootloader, legacy console redirection is disabled before booting the OS. When set to Always Enable, legacy console redirection remains enabled when booting the OS. The options are Always Enable and Bootloader.
  • Page 86 X11DPT-L User's Manual Stop Bits A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard serial data communication. Select 2 Stop Bits if slower devices are used. The options are 1 and 2.
  • Page 87 Chapter 4: UEFI BIOS Serial Port for Out-of-Band Management/Windows Emergency Management Services (EMS) The submenu allows the user to configure Console Redirection settings to support Out-of- Band Serial Port management. This feature allows the user to specify how the host computer will exchange data with the client computer, which is the remote computer used by the user.
  • Page 88 X11DPT-L User's Manual Data Bits: 8 Parity: None Stop Bits: 1 ACPI Settings Numa This setting enables or disables Non-Uniform Memory Access (NUMA), a feature that improves memory-to-processor communication and performance. The options are Disabled and Enabled. WHEA Support Select Enabled to support the Windows Hardware Error Architecture (WHEA) platform and...
  • Page 89 Chapter 4: UEFI BIOS Pending Operation Use this feature to schedule a TPM-related operation to be performed by a security (TPM) device at the next system boot to enhance system data integrity. Your system will reboot to carry out a pending TPM operation. The options are None and TPM Clear. Note: Your system will reboot to carry out a pending TPM operation.
  • Page 90 X11DPT-L User's Manual TXT Support Select Enabled to enable Intel Trusted Execution Technology (TXT) support to enhance system security and data integrity. The options are Disabled and Enabled. Note 1: If the option for this item (TXT Support) is set to Enabled, be sure to disable EV DFX (Device Function On-Hide) support for the system to work properly.
  • Page 91 Chapter 4: UEFI BIOS UEFI Driver This item displays the UEFI driver version. Adapter PBA This item displays the Processor Bus Adapter (PBA) model number. The PBA number is a nine digit number (i.e., 010B00-000) located near the serial number. Device Name This item displays the adapter device name.

  • Page 92: Event Logs

    X11DPT-L User's Manual 4.4 Event Logs Use this feature to configure Event Log settings. Change SMBIOS Event Log Settings  Enabling/Disabling Options SMBIOS Event Log Change this item to enable or disable all features of the SMBIOS Event Logging during system boot.
  • Page 93 Chapter 4: UEFI BIOS SMBIOS Event Long Standard Settings Log System Boot Event This option toggles the System Boot Event logging to enabled or disabled. The options are Enabled and Disabled. MECI The Multiple Event Count Increment (MECI) counter counts the number of occurences that a duplicate event must happen before the MECI counter is incremented.

  • Page 94: Ipmi

    X11DPT-L User's Manual 4.5 IPMI Use this feature to configure Intelligent Platform Management Interface (IPMI) settings. BMC Firmware Revision This item indicates the IPMI firmware revision used in your system. IPMI STATUS (Baseboard Management Controller) This item indicates the status of the IPMI firmware installed in your system.
  • Page 95 Chapter 4: UEFI BIOS When SEL is Full This feature allows the user to decide what the BIOS should do when the system event log is full. Select Erase Immediately to erase all events in the log when the system event log is full.
  • Page 96 X11DPT-L User's Manual Gateway IP Address This item displays the Gateway IP address for this computer. This should be in decimal and in dotted quad form (i.e., 10.135.0.250). VLAN This item displays the virtual LAN settings. The options are Disable and Enable.

  • Page 97: Security

    Chapter 4: UEFI BIOS 4.6 Security This menu allows the user to configure the following security settings for the system. Administrator Password Press Enter to create a new, or change an existing, Administrator password. User Password Press Enter to create a new, or change an existing, user password. Administrator Password Password Check Select Setup for the system to check for a password at Setup.
  • Page 98 X11DPT-L User's Manual Secure Boot This section displays the contents of the following secure boot features: • System Mode • Secure Boot • Vendor Keys Secure Boot Use this item to enable secure boot. The options are Disabled and Enabled.
  • Page 99 Chapter 4: UEFI BIOS  Authorized Signatures This feature allows the user to configure the settings of the Authorized Signatures. The options are Set New and Append.  Forbidden Signatures This feature allows the user to configure the settings of the Forbidden Signatures. The options are Set New and Append.

  • Page 100: Boot

    X11DPT-L User's Manual 4.7 Boot Use this feature to configure Boot Settings: Boot Mode Select Use this item to select the type of device that the system is going to boot from. The options are Legacy, UEFI, and Dual. The default setting is Dual.
  • Page 101 Chapter 4: UEFI BIOS • Legacy/UEFI/Dual/Boot Option #6 • Legacy/UEFI/Dual/Boot Option #7 • Legacy/UEFI/Dual/Boot Option #8 • UEFI/Dual/Boot Option #9 • Dual/Boot Option #10 • Dual/Boot Option #11 • Dual/Boot Option #12 • Dual/Boot Option #13 • Dual/Boot Option #14 •...
  • Page 102 X11DPT-L User's Manual UEFI Boot Option #3 The options are ISATA P0:HGST HUH728080ALE600 (SATA,Port:0), ISATA P1:HGST HUH728080ALE600 (SATA,Port:1), ISATA P2:HGST HUH728080ALE600 (SATA,Port:2), ISATA P3:HGST HUH728080ALE600 (SATA,Port:3), ISATA P4:HGST HUH728080ALE600 (SATA,Port:4), ISATA P5:HGST HUH728080ALE600 (SATA,Port:5), and Disabled. UEFI Boot Option #4...

  • Page 103: Save & Exit

    Chapter 4: UEFI BIOS 4.8 Save & Exit Select the Exit tab from the BIOS setup utility screen to enter the Exit BIOS Setup screen. Save Options Discard Changes and Exit Select this option to quit the BIOS Setup without making any permanent changes to the system configuration, and reboot the computer.
  • Page 104 X11DPT-L User's Manual Default Options Restore Optimized Defaults To set this feature, select Restore Defaults from the Save & Exit menu and press <Enter>. These are factory settings designed for maximum system stability, but not for maximum performance. Save As User Defaults To set this feature, select Save as User Defaults from the Save &...

  • Page 105: Appendix A Bios Codes

    Appendix A: BIOS Codes Appendix A BIOS Codes A.1 BIOS Error POST (Beep) Codes During the POST (Power-On Self-Test) routines, which are performed each time the system is powered on, errors may occur. Non-fatal errors are those which, in most cases, allow the system to continue the boot-up process.
  • Page 106 When BIOS performs the Power On Self Test, it writes checkpoint codes to I/O port 0080h. If the computer cannot complete the boot process, a diagnostic card can be attached to the computer to read I/O port 0080h (Supermicro p/n AOC-LPC80-20). For information on AMI updates, please refer to http://www.ami.com/products/.

  • Page 107: Appendix B Software

    USB/SATA DVD drive, or a USB flash drive, or the IPMI KVM console. 2. Retrieve the proper RST/RSTe driver. Go to the Supermicro web page for your motherboard and click on "Download the Latest Drivers and Utilities", select the proper driver, and copy it to a USB flash drive.
  • Page 108 Super X11DPT-L User's Manual 4. During Windows Setup, continue to the dialog where you select the drives on which to install Windows. If the disk you want to use is not listed, click on “Load driver” link at the bottom left corner.

  • Page 109: Driver Installation

    Appendix B: Software Installation B.2 Driver Installation The Supermicro website that contains drivers and utilities for your system is at https://www. supermicro.com/wftp/driver. Some of these must be installed, such as the chipset driver. After accessing the website, go into the CDR_Images (in the parent directory of the above link) and locate the ISO file for your motherboard.

  • Page 110: Superdoctor ® 5

    B.3 SuperDoctor ® The Supermicro SuperDoctor 5 is a program that functions in a command-line or web-based interface for Windows and Linux operating systems. The program monitors such system health information as CPU temperature, system voltages, system power consumption, fan speed, and provides alerts via email or Simple Network Management Protocol (SNMP).

  • Page 111: Ipmi

    When logging in to the BMC for the first time, please use the unique password provided by Supermicro to log in. You can change the unique password to a user name and password of your choice for subsequent logins.

  • Page 112: Appendix C Standardized Warning Statements

    The following statements are industry standard warnings, provided to warn the user of situations where bodily injury might occur. Should you have questions or experience difficulty, contact Supermicro's Technical Support department for assistance. Only certified technicians should attempt to install or configure components.
  • Page 113 Appendix C: Standardized Warning Statements Attention Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer que par une pile de type semblable ou équivalent, recommandée par le fabricant. Jeter les piles usagées conformément aux instructions du fabricant. ¡Advertencia! Existe peligro de explosión si la batería se reemplaza de manera incorrecta.
  • Page 114 Super X11DPT-L User's Manual Product Disposal Warning! Ultimate disposal of this product should be handled according to all na- tional laws and regulations. 製品の廃棄 この製品を廃棄処分する場合、 国の関係する全ての法律 ・ 条例に従い処理する必要があります。 警告 本产品的废弃处理应根据所有国家的法律和规章进行。 警告 本產品的廢棄處理應根據所有國家的法律和規章進行。 Warnung Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen des Landes erfolgen.

  • Page 115: Appendix D Uefi Bios Recovery

    Warning: Do not upgrade the BIOS unless your system has a BIOS-related issue. Flashing the wrong BIOS can cause irreparable damage to the system. In no event shall Supermicro be liable for direct, indirect, special, incidental, or consequential damages arising from a BIOS update.

  • Page 116: Recovering The Main Bios Block With A Usb Device

    1. Please use a different machine to download the BIOS package for your motherboard or your system from the product page available on our website at www.supermicro.com. 2. Extract the BIOS package to a USB device and rename the BIOS ROM file [BIOSname#.###] that is included in the BIOS package to SUPER.ROM for BIOS...
  • Page 117 Appendix D: UEFI BIOS Recovery 5. After locating the SUPER.ROM file, the system will enter the BIOS Recovery menu as shown below. Note: At this point, you may decide if you want to start the BIOS recovery. If you decide to proceed with BIOS recovery, follow the procedures below.
  • Page 118 Super X11DPT-L User's Manual 7. After the BIOS recovery process is complete, press any key to reboot the system. Note: It is recommended that you update your BIOS after BIOS recovery. Please refer Chapter 3 for BIOS update instructions. 8. Press <Del> during system boot to enter the BIOS Setup utility. From the top of the tool bar, select Boot to enter the submenu.
  • Page 119 Appendix D: UEFI BIOS Recovery 9. When the UEFI Shell prompt appears, type fs# to change the device directory path. Go to the directory that contains the BIOS package you extracted earlier from Step 2. Enter flash.nsh BIOSname#.### at the prompt to start the BIOS update process. Note: Do not interrupt this process until the BIOS flashing is complete.

  • Page 120: Appendix E Configuring Vroc Raid Settings

    RAID settings. The E.3 section describes the use of journaling drive for the RAID5 volume (parity based RAID). Note 1: Only use NVMe devices that have been validated by Supermicro. For the lat- est updates, please contact us or refer to our website at https://www.supermicro.com.
  • Page 121 Appendix E: Configuring VROC RAID Settings 6. When the following screen displays, use the down arrow key to select Intel® VMD Technology and press <Enter> to enter the Intel® VMD Technology submenu. 7. When the Intel® VMD Technology submenu appears, it will display all the PCI slots that can be configured for VMD support on the screen.
  • Page 122 Super X11DPT-L User's Manual 13. Navigate to the Advanced tab. 14. Use the arrow keys to select Intel(R) Virtual RAID on CPU and press <Enter> to access the menu items. The following screen will appear showing that the feature "All Intel VMD Controllers"...
  • Page 123 Appendix E: Configuring VROC RAID Settings 15. Use the arrow keys to select All Intel VMD Controllers and press <Enter> to access the menu items. The following screen will appear. It allows the user to create RAID volumes and configure settings of NVMe devices as detected by the system. Note : A single Intel®...

  • Page 124: Configuring Raid Settings

    Super X11DPT-L User's Manual E.2 Configuring RAID Settings Follow the instructions stated in the E.1 section to access the All Intel VMD Controllers menu items, the following screen will appear. Please carefully follow the instructions listed in this section to configure RAID settings for your devices as desired.
  • Page 125 Appendix E: Configuring VROC RAID Settings To Enter a Name for the RAID Volume From the Create RAID Volume submenu as shown on the previous screen, use the arrow keys to select Name and press <Enter>, and the following screen will display. When the screen above displays, enter a unique name for the RAID volume.
  • Page 126 Super X11DPT-L User's Manual To Set the RAID Level for the RAID Volume From the Create RAID Volume submenu, select RAID Level and press <Enter>. The following screen will display. Use the arrow keys to select the desired RAID level for the RAID volume that you've created.
  • Page 127 Appendix E: Configuring VROC RAID Settings Enabling RAID Spanned over VMD Controllers From the Create RAID Volume submenu, use the arrow keys to select Enter RAID spanned over VMD Controllers and press <Enter>. The following screen will display. Enter a desired setting for your RAID volume in the pop-up menu. The options are (not selected) and X (selected).
  • Page 128 Super X11DPT-L User's Manual To Select Disks for the RAID Volumes From the Create RAID Volume submenu, use the arrow keys to highlight Select Disk: and press <Enter>. The following screen will display. The options are (not selected) and X (selected). Set the features one by one to X to select...
  • Page 129 Appendix E: Configuring VROC RAID Settings To Set Strip Size for the RAID Volume From the Create RAID Volume submenu, use the arrow keys to select Strip Size: and press <Enter>. The following screen will display. From the pop-up menu as shown above, select the desired RAID strip size for your RAID volume and press <Enter>.
  • Page 130 Super X11DPT-L User's Manual To Set the Capacity (GB) for the RAID Volume From the Create RAID Volume submenu, use the arrow keys to select Capacity (GB): and press <Enter>. The following screen will display. Enter the desired RAID capacity (in GB) in the pop-up menu to set the capacity for your...
  • Page 131 Appendix E: Configuring VROC RAID Settings To Create Volumes To finalize your RAID volume configuration, select Create Volume from the Create RAID Volume submenu as shown on the screen below. After selecting Create Volume, press <Enter>. The following screen will appear and display RAID volumes as shown below.
  • Page 132 Super X11DPT-L User's Manual To Display RAID Volumes For detailed RAID volume information, use the arrow keys to select the desired RAID volume as shown below. To Display RAID VOLUME Information When the screen above appears, press <Enter>. The RAID VOLUME INFO menu will appear...
  • Page 133 Appendix E: Configuring VROC RAID Settings To Delete a RAID Volume On the RAID VOLUME INFO menu, use the arrow keys to select Delete and press <Enter> to delete the RAID volume you have selected. The following screen will appear to confirm if you want to delete the RAID Volume. Select Yes to delete the RAID Volume.
  • Page 134 Super X11DPT-L User's Manual To Reset the RAID Volume to non-RAID On the RAID VOLUME INFO submenu shown on the bottom screen of page 132, select the desired NVMe device from the list of RAID Member Disks and press <Enter> as shown below.
  • Page 135 Appendix E: Configuring VROC RAID Settings To Turn on the Disk Locator LED Follow the instructions stated in the E.1 section to access the All Intel VMD Controllers menu. When the following screen displays, select a non-RAID physical disk to turn on the disk locator LED to locate a selected device.
  • Page 136 Super X11DPT-L User's Manual To Mark a RAID Volume as Spare Follow the instructions stated in the E.1 section to access the All Intel VMD Controllers Menu. When the following screen appears, select a desired NVMe device from the list of Non-RAID Physical Disks.
  • Page 137 Appendix E: Configuring VROC RAID Settings When the following screen appears, select Yes to confirm that you want the selected device to be used as a spare device. The options are Yes and No. Note: A spare disk is used for automatic RAID volume rebuilds when status of failed, missing, or at risk is detected on the array disk.
  • Page 138 Super X11DPT-L User's Manual To Mark a RAID Volume as a Journaling Drive Refer to the instructions stated in the E.1 section to access the All Intel VMD Controllers menu. When the following screen appears, select a desired NVMe device from the list of Non-RAID Physical Disks for use as a journaling drive.
  • Page 139 Appendix E: Configuring VROC RAID Settings When the following screen appears, select Yes to confirm that the selected device is to be used as a journaling drive. The options are Yes and No. Note: RAID Write Hole (RWH) is a condition associated with a power/drive-failure/crash while writing to a RAID5 volume.

  • Page 140: Use Of Journaling Drive

    Super X11DPT-L User's Manual E.3 Use of Journaling Drive The following section describes the use of a journaling drive for the RAID5 volume, which is a parity-based RAID. Step 1. Refer to the instructions stated in the E.1 section to access All Intel VMD Controllers menu items.
  • Page 141 Appendix E: Configuring VROC RAID Settings RWH Policy Press <Enter> and the following screen will appear. If any device has been set as a journaling drive (see pages 138 and 139), the options are Distributed PPL, Journaling Drive, and Disable. If no device has been set as a journaling drive, the options are Distributed PPL and Disable.
  • Page 142 Super X11DPT-L User's Manual Step 3. Set the feature, RWH Policy, to Journaling Drive. Press <Enter> and the RWH JD feature will become available as shown below. RWH JD Use the arrow keys to select RWH JD. Press <Enter> and the following screen will appear.
  • Page 143 Appendix E: Configuring VROC RAID Settings Step 4. Use the arrow keys and press <Enter> to select the desired journaling drive from the option list of RWH JD. Step 5. For the changes to take effect, use the arrow keys to select Change RWH settings and press <Enter>.

  • Page 144: Boot Mode Select Feature

    Super X11DPT-L User's Manual Appendix F Secure Boot Settings Secure boot is a feature of UEFI (Unified Extensible Firmware Interface) that ensures boot loaders are digitally signed and validated. The F.1, F.2, and F.3 sections provide instructions on how to enable the secure boot features. The F.4 section states Key Management settings.

  • Page 145: Secure Boot/ Secure Boot Mode/ Csm Support Features

    Appendix F: Secure Boot Settings F.2 Secure Boot/ Secure Boot Mode/ CSM Support Features Press <Del> during system boot to enter the BIOS Setup utility. Navigate to the Security tab as shown below. Use the arrow keys to select Secure Boot and press <Enter> to access the menu items. The following screen will appear.

  • Page 146: Secure Boot Settings

    Super X11DPT-L User's Manual F.3 Secure Boot Settings To have the secure boot support, be sure to follow the steps below (Step 1 ~ Step 4). Step 1. Set Secure Boot Mode to Standard. Press Yes to install factory default keys as needed.
  • Page 147 Appendix F: Secure Boot Settings Step 2. For the changes to take effect, press <F4> to save the settings and exit the BIOS Setup utility. Step 3. Press <Del> during system boot to enter the BIOS Setup utility. Navigate to the Security tab and enter the Secure Boot menu.
  • Page 148 Super X11DPT-L User's Manual Step 4. Press <Del> during system boot to enter the BIOS Setup utility. Navigate to the Security tab and enter the Secure Boot menu. Set Secure Boot to Enabled. For the changes to take effect, press <F4> to save the settings and exit the BIOS Setup utility.

  • Page 149: Key Management Settings

    Appendix F: Secure Boot Settings F.4 Key Management Settings The Key Management menu as shown below, which is available when Secure Boot Mode is set to Custom, allows the secure boot keys to be installed via the external device and be involved in the secure boot process.
  • Page 150 Super X11DPT-L User's Manual Restore Factory Keys  Select and press Yes to restore factory default secure boot keys and key variables. Also, it will reset the system to the User mode. The options are Yes and No. Reset To Setup Mode (available when the System Mode is in User ...
  • Page 151 Appendix F: Secure Boot Settings Export Secure Boot variables  Use this feature to export NVRAM content of secure boot variables to files in a root folder on a file system device. Enroll Efi Image  This feature is to enroll SHA256 hash of the binary into the Authorized Signature Data- base (DB) and to allow the image to run in the secure boot mode.
  • Page 152 Super X11DPT-L User's Manual Remove 'UEFI CA' from DB (available when the system is not in Device  Guard Ready) Select and press Yes to remove Microsoft UEFI CA certificate from the DB. The options are Yes and No. ...
  • Page 153 Appendix F: Secure Boot Settings *Refer to the following settings for keys and signatures related to secure boot.  Platform Key (PK) The Platform Key (PK), which is pre-installed in firmware during manufacturing, provides full control of the secure boot key hierarchy. The options are Details, Export, Update, and Delete.
  • Page 154 Super X11DPT-L User's Manual Export: Use the arrow keys to select Export. It is to save the current PKs to a FAT for- matted USB flash drive. Press <Enter> and the following screen will appear. Note: Refer to the right panel of the screen for the file formats accepted.
  • Page 155 Appendix F: Secure Boot Settings Update: Use the arrow keys to select Update. It is to load the factory defaults or load PKs from a file on the external device. Press <Enter> and the following screen will appear.
  • Page 156 Super X11DPT-L User's Manual To load the factory defaults, navigate to Yes and press <Enter>. The following screen will appear. To load PKs from a file on the external device, navigate to No and press <Enter>.
  • Page 157 Appendix F: Secure Boot Settings When the following screen appears, select the USB flash drive that contains the desired file.
  • Page 158 Super X11DPT-L User's Manual Press <Enter> and the following screen will appear. Delete: Use the arrow keys to select Delete and press <Enter> to clear the current PKs and reset the system to the Setup mode.
  • Page 159 Appendix F: Secure Boot Settings Key Exchange Key  The Key Exchange Key (KEK), which is held by the operating system vendor, can be updated by the holder of the PK and be used by secure boot to protect access to signa- tures databases.
  • Page 160 Super X11DPT-L User's Manual Press <Enter> and the following screen will appear. To load the factory defaults, navigate to Yes and press <Enter>. The following screen will appear. To load KEKs from a file on the external device, navigate to No and press <Enter>. Refer...
  • Page 161 Appendix F: Secure Boot Settings Delete: Use the arrow keys to select Delete and press <Enter>. Navigate to Yes and press <Enter> to clear the current KEKs. Navigate to No and press <Enter> to delete only one certificate from the key database.
  • Page 162 Super X11DPT-L User's Manual Authorized Signatures  Authorized Signature Database (DB) contains authorized signing certificates and digital signatures. The options are Details, Export, Update, Append, and Delete. Select Details to display detailed information of Authorized Signatures. Select Export to save the cur- rent DB to a FAT formatted USB flash drive.
  • Page 163 Appendix F: Secure Boot Settings Forbidden Signatures  Forbidden Signature Database (DBX), which is the inverse of DB, contains forbidden certificates and digital signatures. The options are Details, Export, Update, Append, and Delete. Select Details to display detailed information of Forbidden Signatures. Select Export to save the current DBX to a FAT formatted USB flash drive.
  • Page 164 Super X11DPT-L User's Manual Authorized TimeStamps  Authorized Timestamp Database (DBT) is used to issue and check signed time stamp certificates. The options are Details, Export, Update, Append, and Delete. Select Details to display detailed information of Authorized Timestamps. Select Export to save the cur- rent DBT to a FAT formatted USB flash drive.
  • Page 165 Appendix F: Secure Boot Settings OsRecovery Signatures  OsRecovery Signatures Database (DBR) contains secure boot authorized recovery vari- ables. The options are Details, Export, Update, Append, and Delete. Select Details to display detailed information of OsRecovery Signatures. Select Export to save the current DBR to a FAT formatted USB flash drive.

  • Page 166: Appendix G Configuring Network Interface Card (Nic) Settings

    Super X11DPT-L User's Manual Appendix G Configuring Network Interface Card (NIC) Settings The appendix describes settings of onboard Intel® LAN devices via the BIOS Setup utility supported by the Unified Extensible Firmware Interface (UEFI) driver. G.1 Network Interface Card (NIC) Settings Press <Del>...
  • Page 167 Appendix G: Configuring Network Interface Card (NIC) Settings Onboard LAN1 Option ROM (available when NIC(s) is(are) detected by the system) Use the arrow keys to select Onboard LAN1 Option ROM and press <Enter>. The options are Disabled, Legacy, and EFI. Set this feature to EFI. Note : If Onboard LAN1 Option ROM is set to EFI, all features for onboard LAN op- tion ROM will be set to EFI by the EFI driver.
  • Page 168 Super X11DPT-L User's Manual Use the arrow keys to select the desired onboard LAN device as shown below. Press <Enter> and the following screen will appear. It displays the detailed information for the selected onboard LAN device.
  • Page 169 Appendix G: Configuring Network Interface Card (NIC) Settings Blink LEDs This feature allows the user to set the LED blink duration (in seconds). The valid range is 0~15 (seconds). NIC Configuration Use the arrow keys to select NIC Configuration.
  • Page 170 Super X11DPT-L User's Manual Press <Enter> and the following screen will appear. Wake on LAN Use the arrow keys to select Wake On LAN and press <Enter>. The following screen will appear. The options are Disabled and Enabled. Set this feature to support system wake-up...

Table of Contents