1. Manuals
  2. Brands
  3. D-Link Manuals
  4. Switch
  5. TM DES-6500
  6. Command line interface reference manual

D-Link DES-6500 Command Line Interface Reference Manual

Modular layer 3 switch
Hide thumbs Also See for DES-6500:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual, Cli Manual
DES-6500
Modular Layer 3 Switch
Command Line Interface Reference Manual
Firmware Release 1.3
Third Edition (Febuary 2005)
6DES6500CL03
Printed In Taiwan
RECYCLABLE

Advertisement

Table of Contents
loading

Related Manuals for D-Link DES-6500

Summary of Contents for D-Link DES-6500

  • Page 1 DES-6500 Modular Layer 3 Switch Command Line Interface Reference Manual Firmware Release 1.3 Third Edition (Febuary 2005) 6DES6500CL03 Printed In Taiwan RECYCLABLE...
  • Page 2 Registration Card. If a Registration Card for the product in question has not been returned to a D-Link office, then a proof of purchase (such as a copy of the dated purchase invoice) must be provided when requesting warranty service.
  • Page 3 IF YOU PURCHASED A D-LINK PRODUCT IN THE UNITED STATES, SOME STATES DO NOT ALLOW THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
  • Page 4 Hardware. Repaired or replacement Hardware will be warranted for the remainder of the original Warranty Period from the date of original retail purchase. If a material defect is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to repair or replace the defective Hardware, the price paid by the original purchaser for the defective Hardware will be refunded by D- Link upon return to D-Link of the defective Hardware.
  • Page 5 RMA number is not visible from the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.
  • Page 6 Register online your D-Link product at http://support.dlink.com/register/...

  • Page 7: Copyright Statement

    D-Link Offices for Registration and Warranty Service The product's Registration Card, provided at the back of this manual, must be sent to a D-Link office. To obtain an RMA number for warranty service as to a hardware product, or to obtain warranty service as to a software product, contact the D-Link office nearest you. An address/telephone/fax/e-mail/Web site list of D-Link offices is provided in the back of this manual.

  • Page 8: Fcc Warning

    FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

  • Page 9: Table Of Contents

    Table of Contents Introduction ... 3 Using the Console CLI ... 6 Command Syntax... 10 Basic Switch Commands... 12 Switch Port Commands ... 26 Port Security Commands... 29 Network Management (SNMP) Commands... 32 Switch Utility Commands... 55 Network Monitoring Commands ... 58 Spanning Tree Commands ...
  • Page 10 DNS Relay Commands ...192 VRRP Commands...198 RIP Commands...206 DVMRP Commands...210 PIM Commands ...216 IP Multicasting Commands ...220 MD5 Configuration Commands ...223 OSPF Configuration Commands ...226 Jumbo Frame Commands ...250 Command History List...252 Technical Specifications ...255 International Offices ...257...

  • Page 11: Introduction

    Ctrl+r to refresh the console screen. There is no initial username or password. Just press the Enter key twice to display the CLI input cursor − DES-6500:4#. This is the command line where all commands are input.
  • Page 12 Configuration menu. The IP address for the switch must be set before it can be managed with the Web-based manager. The switch IP address can be automatically set using BOOTP or DHCP protocols, in which case the actual address assigned to the switch must be known.
  • Page 13 DES-6500 In the above example, the switch was assigned an IP address of 10.42.73.204 with a subnet mask of 255.0.0.0. The system message Success indicates that the command was executed successfully. The switch can now be configured and managed via...

  • Page 14: Using The Console Cli

    The DES-6500 supports a console management interface that allows the user to connect to the switch’s management agent via a serial port and a terminal or a computer running a terminal emulation program. The console can also be used over the network using the TCP/IP Telnet protocol.
  • Page 15 DES-6500 Commands are entered at the command prompt, DES-6500:4#. There are a number of helpful features included in the CLI. Entering the ? command will display a list of all of the top-level commands. Figure 2-2. The ? Command When you enter a command without its required parameters, the CLI will prompt you with a Next possible completions: message.
  • Page 16 To re-enter the previous command at the command prompt, press the up arrow cursor key. The previous command will appear at the command prompt. Figure 2-4. Using the Up Arrow to Re-enter a Command In the above example, the command config account was entered without the required parameter <username>, the CLI returned the Next possible completions: <username>...
  • Page 17 DES-6500 For example, if you enter the show command with no additional parameters, the CLI will then display all of the possible next parameters. Figure 2-6. Next possible completions: Show Command In the above example, all of the possible next parameters for the show command are displayed. At the next command prompt, the up arrow was used to re-enter the show command, followed by the account parameter.

  • Page 18: Command Syntax

    The following symbols are used to describe how command entries are made and values and arguments are specified in this manual. The online help contained in the CLI and available through the console interface uses the same syntax. Note: All commands are case-sensitive. Be sure to disable Caps Lock or any other unwanted function that changes case of entered text.
  • Page 19 Displays the next page. Displays the previous page. Stops the display of remaining pages when multiple pages are to be displayed. Refreshes the pages currently displayed. Displays the remaining pages without pausing between pages. Enter Displays the next line or table entry. DES-6500...

  • Page 20: Basic Switch Commands

    The basic switch commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command create account config account show account delete account show session show switch Show stack_information show device_status show serial_port...
  • Page 21 To configure the user password of “dlink” account: show account Used to display user accounts Purpose Syntax show account Displays all user accounts created on the switch. Up to 8 user accounts Description can exist on the switch at one time. DES-6500...
  • Page 22 -------------- dlink DES-6500:4# delete account Purpose Syntax Description Parameters Restrictions Example usage: DES-6500:4#delete account System Command: delete account System Success. DES-6500:4# To delete the user account “System”: show session Purpose Syntax Description None. Only Administrator-level users can issue this command.
  • Page 23 Parameters None Restrictions Only Administrator-level users can issue this command. Example usage: To display the way that the users logged in: DES-6500:4#show session Command: show session ID Live Time --------- *8 03:36:27 Serial Port Total Entries: 1 show switch Used to display information about the switch.
  • Page 24 DES-6500:4# show stack_information Purpose Syntax Description Parameters Restrictions Example usage: To display the stack switch information: : DES-6500 Chassis Ethernet Switch : DA-10-21-00-00-01 : 10.41.44.22 (Manual) : default : 255.0.0.0 : 0.0.0.0 : Build 0.00-B22 : 2A1 : DES-6500_#3 : 7th_flr_east_cabinet...
  • Page 25 8 USR-NOT-CFG ----------------------------------------------------------------- Topology Current state:MASTER Box Count show device status Purpose Used to display the current status of the hardware of the switch. Syntax show device_status Description This command displays the current status of the switch’s elements. Parameters None.
  • Page 26 Purpose Syntax Description Parameters Restrictions Example usage: To display the serial port setting: DES-6500:4#show serial_port Command: show serial_port Baud Rate Data Bits Parity Bits Stop Bits Auto-Logout DES-6500:4# config serial_port Purpose Used to configure the serial port. Syntax...
  • Page 27 Example usage: To configure auto logout: DES-6500:4#config serial_port auto_logout never Command: config serial_port auto_logout never Success. DES-6500:4# enable clipaging Used to pause the scrolling of the console screen when the show Purpose command displays more than one page. Syntax enable clipaging...
  • Page 28 <tcp_port_number 1-65535> This command is used to enable the Telnet protocol on the switch. The user can specify the TCP or UDP port number the switch will use to listen for Telnet requests. <tcp_port_number 1-65535> − The TCP port number. TCP ports are numbered between 1 and 65535.
  • Page 29 Description This command is used to enable the Web-based management software on the switch. The user can specify the TCP port number the switch will use to listen for Telnet requests. <tcp_port_number 1-65535> − The TCP port number. TCP ports are Parameters numbered between 1 and 65535.
  • Page 30 None. Only administrator-level users can issue this command. Used to save changes in the switch’s configuration to non-volatile RAM. save This command is used to enter the current switch configuration into non-volatile RAM. The saved switch configuration will be loaded into the switch’s memory each time the switch is restarted.
  • Page 31 − If the keyword ‘config’ is specified, all of the factory default settings are restored on the switch including the IP address, user accounts, and the switch history log. The switch will not save or reboot. system − If the keyword ‘system’ is specified all of the factory default settings are restored on the switch.
  • Page 32 To restore all of the switch’s parameters to their default values: DES-6500:4#reset config Command: reset config Are you sure you want to proceed with system reset except stack information?(y/n) y Success. DES-6500:4# login Purpose Syntax Description Parameters Restrictions Example usage:...
  • Page 33 DES-6500 Example usage: To terminate the current user’s console session: DES-6500:4#logout...

  • Page 34: Switch Port Commands

    The switch port commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command config ports show ports Each command is listed, in detail, in the following sections. config ports Purpose Used to configure the switch’s Ethernet port settings.
  • Page 35 Only administrator-level users can issue this command. Example usage: To configure the speed of port 3 to be 10 Mbps, full duplex, learning and state enabled: DES-6500:4#config ports 1:3 speed 10_full learning enabled state enabled Command: config ports 1:3 speed 10_full learning enabled state enabled Success.
  • Page 36 DES-6500:4#show ports Command show ports: Port Port Settings Address State Speed/Duplex/FlowCtrl Speed/Duplex/FlowCtrl Learning ------ -------- --------------------- -------- Enabled Auto/Enabled Enabled Enabled Auto/Enabled Enabled Enabled Auto/Enabled Enabled Enabled Auto/Enabled Enabled Enabled Auto/Enabled Enabled Enabled Auto/Enabled Enabled Enabled Auto/Enabled Enabled Enabled Auto/Enabled...

  • Page 37: Port Security Commands

    The switch port security commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command config port_security ports show port_security Each command is listed, in detail, in the following sections. config port_security ports Purpose Used to configure port security settings.
  • Page 38 Used to display the current port security configuration. show port_security {ports <portlist>} This command is used to display port security information of the switch ports. The information displayed includes port security admin state, maximum number of learning address and lock mode.
  • Page 39 Example usage: To display the port security configuration: DES-6500:4#show port_security ports 1:1 – 1:20 Command: show port_security ports 1:1 – 1:20 Port# Admin State Mode ---- ----------- Disabled Disabled Disabled Disabled Disabled Disabled Enabled Disabled Disabled 1:10 Disabled 1:11 Disabled...

  • Page 40: Network Management (Snmp) Commands

    The DES-6500 supports the Simple Network Management Protocol (SNMP) versions 1, 2c, and 3. You can specify which version of the SNMP you want to use to monitor and control the switch. The three versions of SNMP vary in the level of security provided between the management station and the network device.
  • Page 41 <sw_contact> config snmp system_location <sw_location> config snmp system_name <sw_name> enable rmon disable rmon Each command is listed, in detail, in the following sections. DES-6500...
  • Page 42 <priv_password 8-16> − An alphanumeric string of between 8 and 16 characters that will be used to encrypt the contents of messages the host sends to the agent. Restrictions Only administrator-level users can issue this command. Example usage: To create an SNMP user on the switch:...
  • Page 43 DES-6500:4#create snmp user dlink default encrypted by_password auth md5 auth_password priv none Command: create snmp user dlink default encrypted by_password auth md5 auth_password priv none Success. DES-6500:4# delete snmp user Used to remove an SNMP user from an SNMP group and also to delete Purpose the associated SNMP group.
  • Page 44 To display the SNMP users currently configured on the switch: DES-6500:4#show snmp user Command: show snmp user Username --------------- initial Total Entries: 1 DES-6500:4# create snmp view Purpose Syntax Description Parameters Restrictions Example usage: To create an SNMP view: Group Name...
  • Page 45 <view_name 32> − An alphanumeric string of up to 32 characters that identifies the SNMP view to be deleted. all − Specifies that all of the SNMP views on the switch will be deleted. <oid> − The object ID that identifies an object tree (MIB tree) that will be deleted from the switch.
  • Page 46 CommunityView CommunityView Total Entries: 11 DES-6500:4# Used to display an SNMP view previously created on the switch. show snmp view {<view_name 32>} The show snmp view command displays an SNMP view previously created on the switch. <view_name 32> − An alphanumeric string of up to 32 characters that identifies the SNMP view that will be displayed.
  • Page 47 Used to create an SNMP community string to define the relationship between the SNMP manager and an agent. The community string acts like a password to permit access to the agent on the switch. One or more of the following characteristics can be associated with the...
  • Page 48 Restrictions Example usage: To display the currently entered SNMP community strings: Used to remove a specific SNMP community string from the switch. delete snmp community <community_string 32> The delete snmp community command is used to remove a previously defined SNMP community string from the switch.
  • Page 49 Total Entries: 3 config snmp engineID Purpose Used to configure a name for the SNMP engine on the switch. Syntax config snmp engineID <snmp_engineID 10-32> Description The config snmp engineID command configures an identifier for the SNMP engine on the switch.
  • Page 50 SNMP manager. auth_nopriv − Specifies that authorization will be required, but there will be no encryption of packets sent between the switch and a remote SNMP manager. auth_priv − Specifies that authorization will be required, and that packets sent between the switch and a remote SNMP manger will be encrypted.
  • Page 51 Only administrator-level users can issue this command. Example usage: To create an SNMP group named “sg1:” DES-6500:4#create snmp group sg1 v3 noauth_nopriv read_view v1 write_view v1 notify_view v1 Command: create snmp group sg1 v3 noauth_nopriv read_view v1 write_view v1 notify_view v1 Success.
  • Page 52 Syntax Description Used to display the group-names of SNMP groups currently configured on the switch. The security model, level, and status of each group are also displayed. show snmp groups The show snmp groups command displays the group-names of SNMP groups currently configured on the switch.
  • Page 53 SNMP manager. auth_nopriv − Specifies that authorization will be required, but there will be no encryption of packets sent between the switch and a remote SNMP manager. auth_priv − Specifies that authorization will be required, and that packets sent between the switch and a remote SNMP manger will be encrypted.
  • Page 54 Restrictions Example usage: To display the currently configured SNMP hosts on the switch: Used to remove a recipient of SNMP traps generated by the switch’s SNMP agent. delete snmp host <ipaddr> <auth_string 32> The delete snmp host command deletes a recipient of SNMP traps generated by the switch’s SNMP agent.
  • Page 55 Description The create trusted_host command creates the trusted host. The switch allows you to specify up to four IP addresses that are allowed to manage the switch via in-band SNMP, WEB or TELNET based management software. These IP addresses must be members of the Management VLAN.
  • Page 56 Restrictions Example Usage: To delete a trusted host with an IP address 10.48.74.121: Used to display a list of trusted hosts entered on the switch using the create trusted_host command above. show trusted_host {<ipaddr>} This command is used to display a list of trusted hosts entered on the switch using the create trusted_host command above.
  • Page 57 DES-6500:4#delete trusted_host 10.48.74.121 Command: delete trusted_host 10.48.74.121 Success. DES-6500:4# enable snmp traps Purpose Used to enable SNMP trap support. Syntax enable snmp traps Description The enable snmp traps command is used to enable SNMP trap support on the switch. Parameters none.
  • Page 58 Only administrator-level users can issue this command. : Enabled Used to disable SNMP trap support on the switch. disable snmp traps This command is used to disable SNMP trap support on the Switch. none. Only administrator-level users can issue this command.
  • Page 59 The config snmp system_contact command is used to enter the name and/or other information to identify a contact person who is responsible for the switch. A maximum of 255 characters can be used. Parameters <sw_contact> - A maximum of 255 characters is allowed. A NULL string is accepted if there is no contact.
  • Page 60 Parameters Restrictions Example usage: To configure the switch name for “D E S - 6 5 0 0 S w i t c h Used to enter a description of the location of the switch. config snmp system_location <sw_location> The config snmp system_location command is used to enter a description of the location of the switch.
  • Page 61 DES-6500:4#config snmp system_name DES-6500 Switch Command: config snmp system_name DES-6500 Switch Success. DES-6500:4# enable rmon Purpose Used to enable RMON on the switch. Syntax enable rmon Description This command is used, in conjunction with the disable rmon command below, to enable and disable remote monitoring (RMON) on the switch.
  • Page 62 DES-6500:4#disable rmon Command: disable rmon Success. DES-6500:4#...

  • Page 63: Switch Utility Commands

    CPU module, <unitid> is the unit id of the module that will receive the download, if you want to update only one module. Restrictions The TFTP server must be on the same IP subnet as the switch. Only administrator-level users can issue this command. Example usage:...
  • Page 64 Restrictions Example usage: To upload a configuration file: Used to upload the current switch settings or the switch history log to a TFTP server. upload [cfg_toTFTP|log_toTFTP] <ipaddr> <path_filename 64> This command is used to upload either the switch’s current settings or the switch’s history log to a TFTP server.
  • Page 65 - Defines the time-out period while waiting for a response from the remote device. A value of 1 to 99 seconds can be specified. The default is 1 second Restrictions None. DES-6500:4#ping 10.48.74.121 times 4 Command: ping 10.48.74.121 Reply from 10.48.74.121, time<10ms Reply from 10.48.74.121, time<10ms Reply from 10.48.74.121, time<10ms Reply from 10.48.74.121, time<10ms...

  • Page 66: Network Monitoring Commands

    The network monitoring commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command show packet ports show error ports show utilitzation clear counters clear log show log enable syslog disable syslog show syslog create syslog host config syslog host...
  • Page 67 For example, 1:3 specifies slot number 1, port 3. 2:4 specifies slot number 2, port 4. 1:3-2:4 specifies all of the ports between slot 1, port 3 and slot 2, port 4 − in numerical order. Restrictions None. DES-6500 Parameters state [enabled|disabled] <index 1-4> <index 1-4>...
  • Page 68 <portlist> This command will display all of the packet error statistics collected and logged by the switch for a given port list. <portlist> − Specifies a range of ports to be displayed. The port list is specified by listing the lowest slot number and the beginning port number on that slot, separated by a colon.
  • Page 69 Example usage: To display the errors of the port 3 of module 1: DES-6500:4#show errors port 1:3 RX Frames --------------- CRC Error Undersize Oversize Fragment Jabber Drop Pkts show utilization Purpose Used to display real-time port utilization statistics. Syntax show utilization...
  • Page 70 Used to clear the switch’s statistics counters. Syntax clear counters {ports <portlist>} Description This command will clear the counters used by the switch to compile statistics. Parameters <portlist> − Specifies a range of ports to be configured. The port list is specified by listing the lowest slot number and the beginning port number on that slot, separated by a colon.
  • Page 71 Syntax show log {index <value_list>} Description This command will display the contents of the switch’s history log. index <value_list> − The show log command will display the history log Parameters until the log number reaches the value specified by the value_list entry.
  • Page 72 DES-6500:4#show log Index Time ----- ---------- 000d00h50m Unit 1, Successful login through Console (Username: Anonymous) 000d00h50m Unit 1, Logout through Console (Username: Anonymous) 000d00h49m Unit 1, Successful login through Console (Username: Anonymous) 000d00h49m Unit 1, Logout through Console (Username: Anonymous)
  • Page 73 DES-6500:4#disable syslog Command: disable syslog Success. DES-6500:4# show syslog Purpose Used to display the syslog protocol status as enabled or disabled. Syntax show syslog Description The show syslog command displays the syslog status as enabled or disabled. Parameters None. Restrictions None.
  • Page 74 This corresponds to number 4 from the list above. all − Specifies that all of the currently supported syslog messages that are generated by the switch will be sent to the remote host. facility − Some of the operating system daemons and processes have been assigned Facility values.
  • Page 75 Restrictions Only administrator-level users can issue this command. Example usage: To create syslog host: DES-6500 log alert clock daemon local use 0 (local0) local use 1 (local1) local use 2 (local2)
  • Page 76 DES-6500:4#create syslog host 1 severity all facility local0 Command: create syslog host 1 severity all facility local0 Success. DES-6500:4# config syslog host Purpose Used to configure the syslog protocol to send system log data to a remote host. Syntax config syslog host [all|<index 1-4>] {severity [informational|warning|all]| facility[local0|local1|local2|local3| local4|local5|local6|local7]|udp_port <udp_port_number>|...
  • Page 77 [enabled|disabled] − Allows the sending of syslog messages to the remote host, specified above, to be enabled and disabled. Restrictions Only administrator-level users can issue this command. Example usage: To configure a syslog host: DES-6500 network news subsystem UUCP subsystem clock daemon security|authorization messages FTP daemon...
  • Page 78 DES-6500:4#config syslog host all severity all facility local0 Command: config syslog host all severity all facility local0 Success. DES-6500:4# delete syslog host Purpose Syntax Description Parameters Restrictions Example usage: To delete a previously configured syslog host: DES-6500:4#delete syslog host 4 Command: delete syslog host 4 Success.
  • Page 79 Used to display the stack information table. Syntax show stack_information Description This command display stack information. Parameters None. Restrictions None. Usage Example: To display stack information: DES-6500:4#show stack_information Command: show stack_information Type ----------- DES-6507 USR-NOT-CFG USR-NOT-CFG USR-NOT-CFG USR-NOT-CFG USR-NOT-CFG USR-NOT-CFG...

  • Page 80: Spanning Tree Commands

    The switch supports 802.1d STP and 802.1w Rapid STP. The spanning tree commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command config stp config stp ports enable stp disable stp...
  • Page 81 <1-10> - the maximum number of Hello packets transmitted per interval. Default value = 3. version [rstp|stp] - select the Spanning Tree Protocol version used for the switch. For IEEE 802.1d STP select stp. Select rstp for IEEE 802.1w Rapid STP. Restrictions Only administrator-level users can issue this command.
  • Page 82 Example usage: To configure STP with path cost 19, priority 15, and state enabled for ports 1-5 of module 1. DES-6500:4#config stp ports 1:1-1:5 cost 19 priority 15 state enabled Command: config stp ports 1-5 cost 19 priority 15 state enabled Success.
  • Page 83 Used to display the switch’s current STP configuration. Syntax show stp Description This command displays the switch’s current STP configuration. Parameters none Restrictions None. Example usage: To display the status of STP on the switch: Status 1: STP enabled with STP compatible version DES-6500...
  • Page 84 DES-6500:4#show stp Command: show stp STP Status Max Age Hello Time Forward Delay Priority Default Path Cost STP Version TX Hold Count Forwarding BPDU Designated Root Bridge Root Priority Cost to Root Root Port Last Topology Change Topology Changes Count...
  • Page 85 Purpose Used to display the switch’s current per-port group STP configuration. Syntax show stp ports <portlist> Description This command displays the switch’s current per-port group STP configuration. Parameters <portlist> − Specifies a range of ports to be configured. The port list is specified by listing the lowest slot number and the beginning port number on that slot, separated by a colon.

  • Page 86: Forwarding Database Commands

    Used to create a static entry to the unicast MAC address forwarding table (database) create fdb <vlan_name 32> <macaddr> [port <port>] This command will make an entry into the switch’s unicast MAC address forwarding database. <vlan_name 32> − The name of the VLAN on which the MAC address resides.
  • Page 87 Restrictions Only administrator-level users can issue this command. Example usage: To create a unicast MAC FDB entry: DES-6500:4#create fdb default 00-00-00-00-01-02 port 2:5 Command: create fdb default 00-00-00-00-01-02 port 2:5 Success. DES-6500:4# create multicast_fdb Purpose Used to create a static entry to the multicast MAC address forwarding...
  • Page 88 This may cause incorrect packet forwarding decisions by the switch. If the aging time is too short however, many entries may be aged out too soon. This will result in a...
  • Page 89 Parameters <sec 10-1000000> − The aging time for the MAC address forwarding database.
  • Page 90 <port> − The port number corresponding to the MAC destination address. The switch will always forward traffic to the specified device through this port. The port list is specified by listing the lowest slot number and the beginning port number on that slot, separated by a colon.
  • Page 91 Used to display the contents of the switch’s multicast forwarding database. show mulitcast_fdb [vlan <vlan_name 32>|mac_address <macaddr>] This command is used to display the current contents of the switch’s multicast MAC address forwarding database. <vlan_name 32> − The name of the VLAN on which the MAC address resides.
  • Page 92 Restrictions Example usage: To display unicast MAC address table: DES-6500:4#show fdb Command: show fdb Unicast MAC Address Ageing Time = 300 VID VLAN Name ---- ---------------- default default default default default default default default default default default default...

  • Page 93: Broadcast Storm Control Commands

    <storm_grouplist> − Used to specify a broadcast storm control group Parameters with the syntax: module_id:group_id. all − Specifies all broadcast storm control groups on the switch. broadcast [enable|disable] − Enables or disables broadcast storm control. multicast [enable|disable] − Enables or disables multicast storm control.
  • Page 94 DES-6500:4#config traffic control all broadcast enable Command: config traffic control all broadcast enable Success. DES-6500:4# show traffic control Purpose Syntax Description Parameters Restrictions Example usage: To display traffic control setting: DES-6500:4#show traffic control Command: show traffic control Traffic Control Module Group...

  • Page 95: Qos Commands

    The DES-6500 switch supports 802.1p priority queuing. The switch has 8 priority queues. These priority queues are numbered from 0 (Class 0) — the lowest priority queue — to 6 (Class 6) — the highest priority queue. The eight priority queues specified in IEEE 802.1p (p0 to p7) are mapped to the switch’s priority queues as follows:...
  • Page 96 Command show 802.1p default_priority config scheduling_mechanism show scheduling_mechanism enable hol_prevention disable hol_prevention show hol_prevention Each command is listed, in detail, in the following sections. config bandwidth_control Purpose Syntax Description Parameters Restrictions Example usage: To configure bandwidth control: Parameters <priority 0-7> <portlist>...
  • Page 97 DES-6500:4#config bandwidth_control 1:10 tx_rate 10 Command: config bandwidth_control 1:10 tx_rate 10 Success. DES-6500:4# show bandwidth_control Purpose Used to display the bandwidth control configuration on the switch. Syntax show bandwidth_control {<portlist>} Description The show bandwidth_control command displays the current bandwidth control configuration on the switch, on a port-by-port basis.
  • Page 98 Parameters Restrictions Example usage: To configure traffic scheduling: Used to configure traffic scheduling for each of the switch’s QoS queues. config scheduling <class_id 0-6> {max_packet <value 0-15>| The switch contains eight hardware priority queues per device. The switch’s default settings draw down the seven hardware queues in order, from the highest priority (Class 6) to the lowest priority (Class 0).
  • Page 99 The show scheduling command displays the current configuration for the maximum number of packets (max_packets) assigned to the eight priority queues on the switch. At this value, it will empty the eight hardware queues in order, from the highest priority (queue 6) to the lowest priority (queue 0).
  • Page 100 802.1p user_priority <priority 0-7> <class_id 0-6> The config 802.1p user_priority command is used to configure the way the switch will map an incoming packet, based on its 802.1p user priority tag, to one of the eight hardware priority queues available on the switch.
  • Page 101 DES-6500:4# config 802.1p default_priority Purpose Used to specify how to map an incoming packet that has no 802.1p priority tag to one of the switch’s eight hardware priority queues. Syntax config 802.1p default_priority [<portlist>|all] <priority 0-7> Description The config 802.1p default_priority command allows you to specify the 802.1p priority value an untagged, incoming packet will be assigned...
  • Page 102 802.1p default_priority Restrictions Example usage: To configure 802.1p default priority on the switch: DES-6500:4#config 802.1p default_priority all 5 Command: config 802.1p default_priority all 5 Success. DES-6500:4# show 802.1p default_priority Purpose Syntax Description Parameters Restrictions Example usage: To display the current 802.1p default priority configuration on the switch: applied to all ports on the switch.
  • Page 103 This command is used to specify the rotation by which these eight hardware priority queues are emptied. The switch’s default is to empty the 8 hardware priority queues in order − from the highest priority queue (hardware queue 7) to the lowest priority queue (hardware queue 0).
  • Page 104 Parameters Restrictions Example usage: To configure the traffic scheduling mechanism for each COS queue: DES-6500:4#config scheduling_mechanism strict Command: config scheduling_mechanism strict Success. DES-6500:4# show scheduling_mechanism Purpose Used to display the current traffic scheduling mechanisms in use on the switch.
  • Page 105 DES-6500:4#show scheduling_mechanism Command: show scheduling_mechanism QOS scheduling_mechanism CLASS ID Mechanism -------- ----------- Class-0 strict Class-1 strict Class-2 strict Class-3 strict Class-4 strict Class-5 strict Class-6 strict DES-6500:4# enable hol_prevention Purpose Used to enable HOL prevention. Syntax enable hol_prevention Description The enable hol_prevention command enables Head of Line prevention.
  • Page 106 Description The disable hol_prevention command disables Head of Line prevention. Parameters none. Restrictions You must have administrator privileges. Example Usage: To disable HOL prevention: DES-6500:4#disable hol_prevention Command: disable hol_prevention Success. DES-6500:4# show hol_prevention Purpose Used to show HOL prevention. Syntax...

  • Page 107: Port Mirroring Commands

    Each command is listed, in detail, in the following sections. config mirror port <port> add Purpose Used to configure a mirror port − source port pair on the switch. Syntax config mirror port <port> add source ports <portlist> [rx|tx|both] Description...
  • Page 108 Syntax Description Parameters Restrictions Example usage: To delete the mirroring ports: DES-6500:4#config mirror port 1:5 delete source port 1:1-1:5 both Command: config mirror 1:5 delete source 1:1-1:5 both Success. DES-6500:4# Used to delete a port mirroring configuration| config mirror port <port> delete source port <portlist> [rx|tx|both] This command is used to delete a previously entered port mirroring configuration.
  • Page 109 Description This command, combined with the disable mirror command below, allows you to enter a port mirroring configuration into the switch, and then turn the port mirroring on and off without having to modify the port mirroring configuration.
  • Page 110 Syntax Description Parameters Restrictions Example usage: To display mirroring configuration: DES-6500:4#show mirror Command: show mirror Current Settings Mirror Status: Enabled Target Port: 9 Mirrored Port: TX: 1:1-1:5 DES-6500:4# show mirror This command displays the current port mirroring configuration on the switch.

  • Page 111: Vlan Commands

    Syntax create vlan <vlan_name 32> {tag <vlanid 2-4094>|advertisement} Description This command allows you to create a VLAN on the switch. Parameters <vlan_name 32> − The name of the VLAN to be created. <vlanid> − The VLAN ID of the VLAN to be created. Allowed values = 2- 4094 advertisement −...
  • Page 112 DES-6500:4#create vlan v1 tag 2 Command: create vlan v1 tag 2 Success. DES-6500:4# delete vlan Purpose Syntax Description Parameters Restrictions Example usage: To remove the vlan “v1”: DES-6500:4#delete vlan v1 Command: delete vlan v1 Success. DES-6500:4# config vlan Purpose Syntax...
  • Page 113 Restrictions Only administrator-level users can issue this command. Example usage: To add 4 through 8 of module 2 as tagged ports to the VLAN v1: DES-6500:4#config vlan v1 add tagged 2:4-2:8 Command: config vlan v1 add tagged 2:4-2:8 Success. DES-6500:4#...
  • Page 114 Parameters Restrictions Example usage: To set the ingress checking status, the sending and receiving GVRP information : DES-6500:4#config gvrp 1:4 state enabled ingress_checking enabled acceptable_frame tagged_only pvid 2 Command: config gvrp 1:4 state enabled ingress_checking enabled acceptable_frame tagged_only pvid 2 Success.
  • Page 115 Syntax enable gvrp Description This command, along with disable gvrp below, is used to enable and disable GVRP on the switch, without changing the GVRP configuration on the switch. Parameters None. Restrictions Only administrator-level users can issue this command.
  • Page 116 : 1:1-1:12,2:1-2:12 : 1:1-1:12,2:1-2:12 : 1:1-1:12,2:1-2:12 Used to display the GVRP status for a port list on the switch. show gvrp {<portlist>} This command displays the GVRP status for a port list on the switch <portlist> − Specifies a range of ports for which the GVRP status is to be displayed.
  • Page 117 DES-6500:4#show gvrp 1:1-1:16 Command: show gvrp 1:1-1:16 Global GVRP : Disabled Port PVID GVRP ------ ---- -------- Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled 1:10 Disabled 1:11 Disabled 1:12 Disabled 1:13 Disabled 1:14 Disabled 1:15 Disabled 1:16 Disabled...

  • Page 118: Link Aggregation Commands

    <value1-32> {type[lacp|static]} This command will create a link aggregation group with a unique identifier. <value 1-32> − Specifies the group id. The switch allows up to 32 link aggregation groups to be configured. The group number identifies each of the groups.
  • Page 119 This command is used to delete a previously configured link aggregation group. Parameters <value 1-32> − Specifies the group id. The switch allows up to 32 link aggregation groups to be configured. The group number identifies each of the groups.
  • Page 120 <portlist> − Specifies a range of ports that will belong to the link aggregation group. The DES-6500 will only support aggregated links where all of the aggregated ports are contained on the same line card (slot).
  • Page 121 This command will display the current link aggregation configuration of the switch. Parameters <value> − Specifies the group id. The switch allows up to 32 link aggregation groups to be configured. The group number identifies each of the groups. algorithm − Allows you to specify the display of link aggregation by the algorithm in use by that group.
  • Page 122 DES-6500:4#show link_aggregation Command: show link_aggregation Link Aggregation Algorithm = MAC-source-dest Group ID TYPE Master Port Member Port Active Port Status Flooding Port : 1:6 config lacp_ports Purpose Used to configure settings for LACP compliant ports. Syntax config lacp_ports <portlist> mode [active|passive]...
  • Page 123 Example usage: To configure LACP port mode settings: DES-6500:4#config lacp_port 1:1-1:2 mode active Command: config lacp_port 1:1-1:2 mode active Success. DES-6500:4# show lacp_port Purpose Used to display current LACP port mode settings. Syntax show lacp_port {<portlist>} Description This command will display the LACP mode settings as they are currently configured.

  • Page 124: Basic Ip Commands

    Used to enable an IP interface on the switch. enable ipif {<ipif_name> |all} This command will enable the IP interface function on the switch. <ipif_name> − The name for the IP interface to be created. all – Entering this parameter will delete all the IP interfaces currently configured on the switch.
  • Page 125 [enabled|disabled] − Allows you to enable or disable the IP interface. Restrictions Only administrator-level users can issue this command. Example usage: To create an IP interface on the switch: DES-6500:4#create ipif Trinity 10.48.74.122/8 v2 state enabled Command: create ipif Trinity 10.48.74.122/8 v2 state enabled Success. DES-6500:4# config ipif Purpose Used to configure the System IP interface.
  • Page 126 IP address to the switch’s System IP interface. Only administrator-level users can issue this command. Used to display the configuration of an IP interface on the switch. show ipif <ipif_name 12> This command will display the configuration of an IP interface on the switch.
  • Page 127 Purpose Used to delete the configuration of an IP interface on the switch. Syntax delete ipif <ipif_name 12 |all> Description This command will delete the configuration of an IP interface on the switch. Parameters <ipif_name> − The name created for the IP interface.
  • Page 128 DES-6500:4#disable ipif s2 Command: disable ipif s2 Success. DES-6500:4#...

  • Page 129: Igmp Snooping Commands

    <sec> − Specifies the maximum amount of time a host can be a member of a multicast group without the switch receiving a host membership report. The default is 260 seconds. router_timeout <sec> − Specifies the maximum amount of time a route can be a member of a multicast group without the switch receiving a host membership report.
  • Page 130 Restrictions Example usage: To configure the IGMP snooping: DES-6500:4#config igmp_snooping default host_timeout 250 state enabled Command: config igmp_snooping default host_timeout 250 state enabled Success. DES-6500:4# config igmp_snooping querier Purpose Syntax Description Parameters leave_timer <sec> − Leave timer. The default is 2 seconds.
  • Page 131 You might lower this interval to reduce the amount of time it takes a router to detect the loss of the last member of a group. state [enabled|disabled] − Allows the switch to be specified as an IGMP Querier or Non-querier. Restrictions Only administrator-level users can issue this command.
  • Page 132 Used to enable IGMP snooping on the switch. enable igmp_snooping {forward_mcrouter_only} This command allows you to enable IGMP snooping on the switch. If forward_mcrouter_only is specified, the switch will only forward all multicast traffic to the multicast router, only. Otherwise, the switch forwards all multicast traffic to any IP router.
  • Page 133 DES-6500:4#disable igmp_snooping Command: disable igmp_snooping Success. DES-6500:4# show igmp_snooping Purpose Used to show the current status of IGMP snooping on the switch. Syntax show igmp_snooping {vlan <vlan_name 32>} Description This command will display the current IGMP snooping configuration on the switch.
  • Page 134 DES-6500:4#show igmp_snooping Command: show igmp_snooping IGMP Snooping Global State Multicast router Only VLAN Name Query Interval Max Response Time Robustness Value Last Member Query Interval Host Timeout Route Timeout Leave Timer Querier State Querier Router Behavior State Total Entries: 1...
  • Page 135 Reports Port Member Total Entries DES-6500:4# show router_ports Purpose Used to display the currently configured router ports on the switch. Syntax show router_ports {vlan <vlan_name 32>} {static|dynamic|forbidden} Description This command will display the router ports currently configured on the switch.
  • Page 136 Syntax Description Parameters Restrictions Example usage: To view the IGMP snooping forwarding table for VLAN “Trinity”: DES-6500:4#show igmp_snooping forwarding vlan Trinity Command: show igmp_snooping forwarding vlan Trinity VLAN Name Multicast group : 224.0.0.2 MAC address Port Member Total Entries: 1...

  • Page 137: Commands

    The DES-6500 implements the server-side of the IEEE 802.1x Port-based Network Access Control. This mechanism is intended to allow only authorized users, or other network devices, access to network resources by establishing criteria for each port on the switch that a user or network device must meet before allowing that port to forward or receive frames.
  • Page 138 To disable 802.1x on the switch: Parameters {ports [<portlist>|all]} {ports [<portlist>|all]} {ports [<portlist>|all]} Used to enable the 802.1x server on the switch. enable 802.1x The enable 802.1x command enables the 802.1x Port-based Network Access control server application on the switch. None.
  • Page 139 <username 15> − A username can be as many as 15 alphanumeric characters. Restrictions Only administrator-level users can issue this command. Example Usage: To create an 802.1x user: DES-6500:4#create 802.1x user dtremblett Command: create 802.1x user dtremblett Enter a case-sensitive new password:****** Enter the new password again for confirmation:****** Success. DES-6500:4# show 802.1x user...
  • Page 140 Password -------------- Trinity Used to delete an 802.1x user account on the switch. delete 802.1x user <username 15> The delete 802.1x user command is used to display the 802.1x Port- based Network Access control local users currently configured on the switch.
  • Page 141 Authentication Protocol: Radius_Eap − Shows the authentication protocol suite in use between the switch and a Radius server. Port number − Shows the physical port number on the switch. Capability: Authenticator|None − Shows the capability of 802.1x functions on the port number displayed above.
  • Page 142 <portlist> − Specifies a range of ports. The port list is specified by listing the lowest switch number and the beginning port number on that switch, separated by a colon. Then highest switch number, and the highest port number of the range (also separated by a colon) are specified.
  • Page 143 Unauthorized means that the user was not authenticated, and cannot access the network. Restrictions Only administrator-level users can issue this command. Example usage: To display the 802.1x auth state: DES-6500:4#show 802.1x auth_state Command: show 802.1x auth_state Port Auth PAE State ------ -----------------------...
  • Page 144 802.1x capability Parameters Restrictions Example usage: To configure 802.1x capability on ports 1-10 on switch 1: DES-6500:4#config 802.1x capability ports 1:1 – 1:10 authenticator Command: config 802.1x capability ports 1-10 authenticator Success. DES-6500:4# config 802.1x auth_parameter Purpose Syntax Description Parameters None.
  • Page 145 Enabled causes re-authentication of users at the time interval specified in the Re-authentication Period field, above. Restrictions Only administrator-level users can issue this command. Example usage: To configure 802.1x authentication parameters for ports 1 – 20 of switch 1: DES-6500...
  • Page 146 DES-6500:4#config 802.1x auth_parameter ports 1:1 – 1:12 direction both Command: config 802.1x auth_parameter ports 1:1 – 1:12 direction both Success. DES-6500:4# config 802.1x auth_protocol Purpose Syntax Description Parameters Restrictions Example usage: To configure the authentication protocol on the switch: DES-6500:4# Command: config 802.1x auth_protocol local...
  • Page 147 Restrictions Only administrator-level users can issue this command. Example usage: To initialize the authentication state machine of some or all: DES-6500:4# config 802.1x init port_based ports all Command: config 802.1x init port_based ports all Success. DES-6500:4# config 802.1x reauth ports Purpose Used to configure the 802.1x re-authentication feature of the switch.
  • Page 148 Parameters Restrictions Example usage: To configure the RADIUS server communication setttings: DES-6500:4#config radius add 1 10.48.74.121 key dlink default Command: config radius add 1 10.48.74.121 key dlink default Success. DES-6500:4# Used to configure the settings the switch will use to communicate with a RADIUS server.
  • Page 149 {ipaddress <server_ip>|key <passwd 32>|auth_port <udp_port_number 1-65535>|acct_port <udp_port_number 1- 65535>} Description The config radius command is used to configure the switch’s Radius settings. Parameters <server_index 1-3> − Assigns a number to the current set of RADIUS server settings. Up to 3 groups of RADIUS server settings can be entered on the switch.
  • Page 150 Restrictions Example usage: To configure the RADIUS settings: DES-6500:4#config radius 1 10.48.74.121 key dlink default Command: config radius 1 10.48.74.121 key dlink default Success. DES-6500:4# show radius Purpose Syntax Description Parameters Restrictions Example usage: To display RADIUS settings on th switch:...
  • Page 151 The show acct_client command is used to display the current RADIUS accounting client currently configured on the switch. Parameters None. Restrictions None. Example usage: To view the current RADIUS accounting client: DES-6500:4#show acct_client Command: show acct_client radiusAcctClient ==> radiusAcctClientIdentifier radiusAuthServerEntry ==> radiusAccServerIndex : 1 radiusAccServerAddress radiusAccClientServerPortNumber...
  • Page 152 10.53.13.199 Quit SPACE n Next Page Used to display the current authentication diagnostics. show auth_diagnostics {ports [<portlist>|all]} The show auth_diagnostics command is used to display the current authentication diagnostics of the switch on a per port basis. Enter Next Entry...
  • Page 153 Used to display the current authentication session statistics. Syntax show auth_session statistics {ports [<portlist>|all]} Description The show auth_session statistics command is used to display the current authentication session statistics of the switch on a per port DES-6500 Quit SPACE n Next Page...
  • Page 154 <portlist> − Specifies a range of ports. The port list is specified by listing the lowest switch number and the beginning port number on that switch, separated by a colon. Then highest switch number, and the highest port number of the range (also separated by a colon) are specified.
  • Page 155 Restrictions None. Example usage: To display the current authentication statistics for port 16: DES-6500:4#show auth_statistics ports 1:11 Command: show auth_statistics ports 1:11 Port number : 1:11 EapolFramesRx EapolFramesTx EapolStartFramesRx EapolReqIdFramesTx EapolLogoffFramesRx EapolReqFramesTx EapolRespIdFramesRx EapolRespFramesRx InvalidEapolFramesRx EapLengthErrorFramesRx LastEapolFrameVersion LastEapolFrameSource...

  • Page 156: Access Control List (Acl) Commands

    The DES-6500 implements Access Control Lists that enable the Switch to deny network access to specific devices or device groups based on IP settings, MAC address, and packet content. Command create access_profile delete access_profile profile_id config access_profile profile_id show access_profile Due to a chipset limitation, the Switch currently supports a maximum of 8 access profiles, each containing a maximum of 100 rules −...
  • Page 157 − in this case, when a logical AND operation between an IP address specified in the next step and the ip_source_mask match. The default for an access profile on the Switch is to permit traffic flow. If you want to restrict traffic, you must use the deny parameter.
  • Page 158 Purpose Syntax Description Parameters Restrictions Example usage: To create a Ethernet access profile: DES-6500:4#create access_profile ethernet vlan 802.1p profile-id 1 Command: create access_profile ethernet vlan 802.1p profile-id 1 Success. DES-6500:4# config access_profile profile_id (for Ethernet) Purpose Parameters 0xffffffff> <hex 0x0-0xffffffff> | offset_48-63 <hex 0x0-0xffffffff>...
  • Page 159 (for Ethernet) define specific values for the rules that will be used to by the Switch to determine if a given packet should be forwarded or filtered. Masks entered using the create access_profile command will be combined, using a logical AND operational method, with the values the Switch finds in the specified frame header fields.
  • Page 160 (for Ethernet) Restrictions Example usage: DES-6500:4#config access profile profile_id 1 add access_id 1 ethernet vlan Trinity 802.1p 1 port 1:1 permit priority 1 replace priority Command: config access profile profile_id 1 add access_id 1 ethernet vlan Trinity 802.1p 1 port 1:1 permit priority 1 replace priority Success.
  • Page 161 Purpose Used to configure the IP access profile on the Switch and to define specific values for the rules that will be used to by the Switch to determine if a given packet should be forwarded or filtered. Masks entered using the create access_profile command will be combined, using a logical AND operational method, with the values the Switch finds in the specified frame header fields.
  • Page 162 Up to 100 different rules may be configured for the Ethernet access profile. ip − Specifies that the Switch will look into the IP fields in each packet to see if it will be either forwarded or filtered based on one or more of the following: vlan <vlan_name 32>...
  • Page 163 <port> - The access profile for Ethernet may be defined for each port on the Switch. Up to 100 rules may be configured for each port. The port list is specified by listing the switch ID number and the port number on that switch, separated by a colon.
  • Page 164 Packet content masks entered will specify certain bytes of the packet header to be identified by the Switch. When the Switch recognizes a packet with the identical byte as the one configured, it will either forward or filter the packet, based on the users command entered here.
  • Page 165 <port> - The access profile for Ethernet may be defined for each port on the Switch. Up to 100 rules may be configured for each port. The port list is specified by listing the switch ID number and the port number on that switch, separated by a colon.
  • Page 166 (packet content mask) Restrictions Example usage: DES-6500:4# config access_profile profile_id 3 add access_id 1 packet_content offset_0-15 0x11111111 0x11111111 0x11111111 0x11111111 offset_16-31 0x11111111 0x11111111 0x11111111 0x11111111 port 1:1 deny Command: config access_profile profile_id 3 add access_id 1 packet_content offset_0-15 0x11111111 0x11111111 0x11111111...
  • Page 167 This value is assigned to the access profile when it is created with the create access_profile command. Entering this command without the profile_id parameter will command the Switch to display all access profile entries. Restrictions Only administrator-level users can issue this command.
  • Page 168 Offset 0-15 : 0x11111111 0x11111111 0x11111111 0x11111111 Offset 16-31 : 0x00001111 0x11110000 0x00000001 0x01000000 ===================================================================== DES-6500:4# To display all of the currently configured access profiles on the Switch: TYPE : Ethernet Mode: Permit(replaced) priority: 1 TYPE : IP Mode: Deny...

  • Page 169: Traffic Segmentation Commands

    1, port 3. 2:4 specifies slot number 2, port 4. 1:3- 2:4 specifies all of the ports between slot 1, port 3 and slot 2, port 4 − in numerical order. all − Specifies that all of the ports on the switch will be in the forwarding list. Restrictions Only administrator-level users can issue this command.
  • Page 170 DES-6500:4# config traffic_segmentation 1-10 forward_list 11- Command: config traffic_segmentation 1-10 forward_list 11- Success. DES-6500:4# show traffic_segmentation Purpose Syntax Description Parameters Restrictions Example usage: To display the current traffic segmentation configuration on the switch. Used to display the current traffic segmentation configuration on the switch.
  • Page 171 DES-6500 DES-6500:4#show traffic_segmentation Command: show traffic_segmentation Traffic Segmentation Table Port Forward Portlist ---- ---------------------------- 1:1-1:12,2:1-2:12 1:1-1:12,2:1-2:12 1:1-1:12,2:1-2:12 1:1-1:12,2:1-2:12 1:1-1:12,2:1-2:12 1:1-1:12,2:1-2:12 1:1-1:12,2:1-2:12 1:1-1:12,2:1-2:12 1:1-1:12,2:1-2:12 1:10 1:1-1:12,2:1-2:12 1:11 1:1-1:12,2:1-2:12 1:12 1:1-1:12,2:1-2:12 1:1-1:12,2:1-2:12 1:1-1:12,2:1-2:12 1:1-1:12,2:1-2:12 1:1-1:12,2:1-2:12 1:1-1:12,2:1-2:12 1:1-1:12,2:1-2:12 CTRL+C ESC q Quit SPACE n...

  • Page 172: Time And Sntp Commands

    The Simple Network Time Protocol (SNTP) (an adaptation of the Network Time Protocol (NPT)) commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command config sntp show sntp enable sntp disable sntp config time config time-zone config dst...
  • Page 173 Only administrator-level users can issue this command. SNTP service must be enabled for this command to function (enable sntp). Example usage: To configure SNTP settings: DES-6500:4#config sntp primary 10.1.1.1 secondary 10.1.1.2 poll-interval 30 Command: config sntp primary 10.1.1.1 secondary 10.1.1.2 poll-interval 30 Success.
  • Page 174 Syntax Description Parameters Restrictions Example usage: To enab le the SNTP function: DES-6500:4#enable sntp Command: enable sntp uccess. ES-6500:4# disable sntp Purpose Syntax Description Parameters Restrictions xample: stop SNTP support: DES-6500:4#disable sntp Command: disable sntp Success. DES-6500:4# config time...
  • Page 175 Restrictions Only administrator-level users can issue this configured system time and date settings are overridden if SNTP support is enabled. Example usage: DES-6500:4#config time 30jun2003 16:30:30 Command: config time 30jun2003 16:30:30 Success. ES-6500:4# To manually set system time and d...
  • Page 176 DES-6500:4#config time_zone operator + hour 2 min 30 Command: config time_zone operator + hour 2 min 30 uccess. ES-6500:4# config dst Purpose Used to enable and configure time adjustments to allow for the use of Daylight Savings Time (DST). Syntax config dst disable | repeating {s-week<start_week 1-4,last>...
  • Page 177 - Indicates number of minutes to add during the summertime. Th range of offset are 30,60,90,120; def Restrictions Only administrator-level users can issue this command. Example usage: To configure daylight savings time on the switch: DES-6500 ssed numerically. ault value is 60 is the...
  • Page 178 DES-6500:4#config dst repeating s_week 2 s_day tue s_mth 4 s_time 15:00 e_week 2 e_day wed e_mth 10 e_time 15:30 offset 30 Command: config dst repeating s_week 2 s_day tue s_mth 4 s_time 15:00 e_week 2 e_day wed e_mth 10 e_time 15:30 offset 30 Success.

  • Page 179: Arp Commands

    Restrictions Only administrator-level users can issue this command. Example Usage: To create a static arp entry for the IP address 10.48.74.121 and MAC address 00:50:BA:00:07:36: DES-6500:4#create arpentry 10.48.74.121 00-50-BA-00-07-36 Command: create arpentry 10.48.74.121 00-50-BA-00-07-36 Success. DES-6500:4# delete arpentry Purpose Used to delete a static entry into the ARP table.
  • Page 180 − deletes all ARP entries. Only administrator-level users can issue this command. Used to configure the age-out timer for ARP table entries on the switch. config arp_aging time <value 0-65535> This command sets the maximum amount of time, in minutes, that an ARP entry can remain in the switch’s ARP table, without being...
  • Page 181 Syntax show arpentry {ipif <ipif_name>| ipaddress <network_address> | static} Description This command is used to display the current contents of the switch’s ARP table. Parameters <ipif_name> − The name of the IP interface the end node or station for which the ARP table entry was made, resides on.
  • Page 182 Used to remove all dynamic ARP table entries. clear arptable This command is used to remove dynamic ARP table entries from the switch’s ARP table. Static ARP table entries are not affected. none. Only administrator-level users can issue this command.

  • Page 183: Routing Table Commands

    Used to create IP route entries to the switch’s IP routing table. Syntax create iproute [default | <network_address>] <ipaddr> {<metric>} Description This command is used to create an IP route entry to the switch’s IP routing table. Parameters default − creates a default IP route entry.
  • Page 184 Command: create iproute 10.48.74.121/8 10.1.1.254 1 Success. DES-6500:4# delete iproute Purpose Used to delete an IP route entry from the switch’s IP routing table. Syntax delete iproute [default | <network_address>] Description This command will delete an existing entry from the switch’s IP routing table.
  • Page 185 – use this to display RIP iproute entries. ospf – use this to display OSPF iproute entries. Restrictions none. Example Usage: To display the contents of the IP routing table: DES-6500:4#show iproute Command: show iproute IP Address --------------- 0.0.0.0 10.0.0.0...

  • Page 186: Route Redistribution Commands

    RIP routing protocols to all routers on the network that are running OSPF or RIP. Routing information entered into the Static Routing Table on the local DES-6500 switch is also redistributed. src [static/rip/local] − Allows for the selection of the protocol for the source device.
  • Page 187 Allowed Metric Type combinations are mettype 1 or mettype 2. The metric value 0 above will be redistributed in OSPF as the metric 20. Example Usage: To add route redistribution settings: DES-6500:4#create route redistribute dst ospf src rip Command: create route redistribute dst ospf src rip Success. DES-6500:4#...
  • Page 188 To add route redistribution settings: DES-6500:4#create route redistribute dst rip src ospf all metric 2 Command: create route redistribute dst rip src ospf all metric 2 Success. DES-6500:4# delete route redistribute Purpose Syntax Description Parameters Restrictions Example Usage: To delete route redistribution settings:...
  • Page 189 The switch can redistribute routing information DES-6500 Metric...
  • Page 190 OSPF and RIP routing protocols to all routers on the network that are running OSPF or RIP. Routing information entered into the Static Routing Table on the local switch is also redistributed. Parameters src − Allows the selection of the routing protocol on the source device.
  • Page 191 To display route redistributions: DES-6500:4#show route redistribute Command: show route redistribute Source Destination Protocol Protocol -------- ------------ STATIC LOCAL OSPF Total Entries : 2 DES-6500:4# DES-6500 Type Metric -------- -------- Type-2...

  • Page 192: Igmp Commands

    2>/query_interval <sec 1 - 65535>/max_response_time < sec 1-25>/ robustness_variable <value 1-255>/last_member_query_interval <value 1-25>/state [enabled/disabled]} This command is used to configure IGMP on the switch. <ipif_name 12> − The name of the IP interface for which you want to configure IGMP.
  • Page 193 To configure the IGMP for the IP interface System: DES-6500:4#config igmp all version 1 state enabled Command: config igmp all version 1 state enabled Success. DES-6500:4# show igmp Purpose Used to display the IGMP configuration for the switch of for a specified IP interface.
  • Page 194 <group> − The multicast group ID. Parameters <ipif_name> − The name of the IP interface the IGMP group is part of. Restrictions none. Example Usage: To display IGMP group table: DES-6500:4#show igmp group Command: show igmp group Interface -------------------- ------------------- System System System...

  • Page 195: Bootp Relay Commands

    <value> − Specifies the maximum number of relay agent hops that Parameters the BOOTP packets can cross. time <sec> − If this time is exceeded, the switch will relay the BOOTP packet. Restrictions Only administrator-level users can issue this command.
  • Page 196 Syntax Description Parameters Restrictions Example Usage: To add a BOOTP relay. DES-6500:4#config bootp_relay add ipif System 10.43.21.12 Command: config bootp_relay add ipif System 10.43.21.12 Success. DES-6500:4# config bootp_relay delete Purpose Syntax Description Parameters Restrictions config bootp_relay add ipif <ipif_name> <ipaddr>...
  • Page 197 Example Usage: To delete a BOOTP relay: DES-6500:4#config bootp_relay delete ipif System 10.43.21.12 Command: config bootp_relay delete ipif System 10.43.21.12 Success. DES-6500:4# enable bootp_relay Purpose Used to enable the BOOTP relay function on the switch. Syntax enable bootp_relay Description This command, in combination with the disable bootp_relay command below, is used to enable and disable the BOOTP relay function on the switch.
  • Page 198 Description This command will display the current BOOTP relay configuration for the switch, or if an IP interface name is specified, the BOOTP relay configuration for that IP interface. <ipif_name> − The name of the IP interface for which you what to Parameters display the current BOOTP relay configuration.
  • Page 199 DES-6500 Example Usage: To display bootp relay status: DES-6500:4#show bootp_relay Command: show bootp_relay Bootp Relay Status : Disabled Bootp Hops Count Limit Bootp Relay Time Threshold : 0 Interface Server 1 Server 2 Server 3 Server 4 ------------ --------------- ---------------...

  • Page 200: Dns Relay Commands

    [[primary/secondary] nameserver <ipaddr>|[add|delete] static <domain_name> <ipaddr>] This command is used to configure the DNS relay function on the switch. primary − Indicates that the IP address below is the address of the primary DNS server. secondary − Indicates that the IP address below is the address of the secondary DNS server.
  • Page 201 Command: config dnsr primary nameserver 10.43.21.12 Success. DES-6500:4# Example Usage: To add an entry domain name dns1, IP address 10.43.21.12 to DNS static table: DES-6500:4#config dnsr add static dns1 10.43.21.12 Command: config dnsr add static dns1 10.43.21.12 Success. DES-6500:4# Example Usage: To delete an entry domain name dns1, IP address 10.43.21.12 from DNS static table.
  • Page 202 {cache|static} This command is used, in combination with the disable dnsr command below, to enable and disable DNS Relay on the switch. cache – This parameter will allow the user to enable the cache lookup for the DNS rely on the switch.
  • Page 203 {cache|static} Description This command is used, in combination with the enable dnsr command above, to enable and disable DNS Relay on the switch. Parameters cache – This parameter will allow the user to disable the cache lookup for the DNS rely on the switch.
  • Page 204 Example Usage: To disable cache lookup for DNS relay. DES-6500:4#disable dnsr cache Command: disable dnsr cache Success. DES-6500:4# Example Usage: To disable static table lookup for DNS relay. DES-6500:4#disable dnsr static Command: disable dnsr static Success. DES-6500:4# show dnsr Purpose...
  • Page 205 Example Usage: To display DNS relay status: DES-6500:4#show dnsr static Command: show dnsr static DNS Relay Static Table Domain Name -------------------------------------- --------------- www.123.com.tw bbs.ntu.edu.tw Total Entries: 2 DES-6500:4# Example usage: To display DNS relay table: DES-6500:4#show dnsr Command: show dnsr...

  • Page 206: Vrrp Commands

    LAN. This retains the link and the connection is kept alive, regardless of the point of failure. To configure VRRP for virtual routers on the Switch, an IP interface must be present on the system and it must be a part of a VLAN.
  • Page 207 {ping} - Adding this parameter to the command will stop the virtual IP address from being pinged from other host end nodes to verify connectivity. This will only disable the ping connectivity check function. To disable the VRRP protocol on the Switch, omit this parameter. Restrictions Only administrator-level users can issue this command.
  • Page 208 <int 1-255> | preempt [true | false] | critical_ip <ipaddr> | critical_ip_state [enable | disable]} Description This command is used to create a VRRP interface on the Switch. Parameters vrid <vrid 1-255> - Enter a value between 1 and 255 to uniquely identify this VRRP group on the Switch.
  • Page 209 Example usage: DES-6500:4#create vrrp vrid 1 ipif Darren ipaddress 11.1.1.1 state enable priority 200 advertisement_interval 1 preempt true critical_ip 10.53.13.224 critical_ip_state enable Command: create vrrp vrid 1 ipif Darren ipaddress 11.1.1.1 state enable priority 200 advertisement_interval 1 preempt true critical_ip 10.53.13.224 critical_ip_state enable Success.
  • Page 210 config vrrp vrid Restrictions Example usage: To configure a VRRP entry: routers participating within the same VRRP group. The default setting is true. critical_ip <ipaddr> - Enter the IP address of the physical device that will provide the most direct route to the Internet or other critical network connections from this virtual router.
  • Page 211 DES-6500:4#config vrrp vrid 1 ipif Trinity state enable priority 100 advertisement_interval 2 config vrrp ipif Purpose To configure the authentication type for the VRRP routers of an IP interface. Syntax config vrrp ipif <ipif_name 12> [authtype [none | simple authdata <string 8> | ip authdata <string 16>]...
  • Page 212 Checking Critical IP Advertisement Interval : 1 secs Preempt Mode Virtual Router Up Time : 2754089 centi-secs Total Entries : 1 DES-6500:4# To view the global VRRP settings currently implemented on the Switch (VRRP Enabled): delete vrrp Purpose Syntax Description Parameters...
  • Page 213 DES-6500 DES-6500:4#delete vrrp vrid 2 ipif Trinity Command: delete vrrp vrid 2 ipif Trinity Success. DES-6500:4#...

  • Page 214: Rip Commands

    [ipif <ipif_name 12>/all] rx_mode [[disable/v1_only]/[v2_only/v1_or_v2] authentication [enabled/disabled] <password>] This command is used to configure RIP on the switch. <ipif_name 12> − The name of the IP interface. all – To configure all RIP receiving mode for all IP interfaces.
  • Page 215 To change the RIP receive mode for the IP interface System: DES-6500:4#config rip ipif System rx_mode v1_only Command: config rip ipif System rx_mode v1_only Success. DES-6500:4# config rip tx_mode Purpose Used to configure RIP’s transmission mode. Syntax config rip [ipif <ipif_name>|all]} tx_mode [disabled|v1_only|v1_compatible|v2_only] authentication [enabled|disabled] <password>]...
  • Page 216 DES-6500:4#config rip ipif System tx_mode v1_only Command: config rip ipif System tx_mode v1_only Success. DES-6500:4# enable rip Purpose Syntax Description Parameters Restrictions Example Usage: To enable RIP: DES-6500:4#enable rip Command: enable rip Success. DES-6500:4# disable rip Purpose Syntax Description Parameters...
  • Page 217 Command: disable rip Success. DES-6500:4# show rip Purpose Used to display the RIP configuration and statistics for the switch. Syntax show rip {ipif <ipif_name>} Description This command will display the RIP configuration and statistics for a given IP interface or for all IP interfaces.

  • Page 218: Dvmrp Commands

    Used to configure DVMRP on the switch. config dvmrp [ipif <ipif_name>/all] {metric <value>/probe <second>/neighbor_timeout <second>/state [enabled/disabled] This command is used to configure DVMRP on the switch. <ipif_name> − The name of the IP interface for which DVMRP is to be configured.
  • Page 219 Example Usage: To configure DVMRP configurations of IP interface System: DES-6500:4#config dvmrp ipif System neighbor_timeout 30 metric 1 probe 5 Command: config dvmrp ipif System neighbor_timeout 30 metric 1 probe 5 Success DES-6500:4# enable dvmrp Purpose Used to enable DVMRP.
  • Page 220 DES-6500:4#disable dvmrp Command: disable dvmrp Success. DES-6500:4# show dvmrp routing_table Purpose Used to display the current DVMRP routing table. Syntax show dvmrp routing_table {ipaddress <network_address>} Description The command is used to display the current DVMRP routing table. Parameters <ipif_name> − The name of the IP interface for which you want to display the corresponding DVMRP routing table.
  • Page 221 Example Usage: To display DVMRP routing table: DES-6500:4#show dvmrp routing_table Command: show dvmrp routing_table DVMRP Routing Table Source Address --------------- 10.0.0.0/8 20.0.0.0/8 30.0.0.0/8 Total Entries: 3 DES-6500:4# show dvmrp neighbor Purpose Used to display the DVMRP neighbor table. Syntax show dvmrp neighbor {ipif <ipif_name>/ipaddress <network_address>}...
  • Page 222 Example Usage: To display DVMRP neighbor table: DES-6500:4#show dvmrp neighbor Command: show dvmrp neighbor DVMRP Neighbor Address Table Interface Neighbor Address --------------- System Total Entries: 1 DES-6500:4# show dvmrp nexthop Purpose Syntax Description Parameters Restrictions Generation ID ----------------------- ------------------- 10.2.1.123 Used to display the current DVMRP routing next hop table.
  • Page 223 Example Usage: To display DVMRP routing next hop table: DES-6500:4#show dvmrp nexthop Command: show dvmrp nexthop Source IP Address ----------------- 10.0.0.0/8 10.0.0.0/8 20.0.0.0/8 Total Entries: 3 DES-6500:4# show dvmrp Purpose Used to display the DVMRP configurations. Syntax show dvmrp {<ipif_name>}...

  • Page 224: Pim Commands

    – This can enable or disable PIM for the specified IP interface. The default is disabled. Note that PIM settings must also be enabled globally for the switch with the enable pim described below for PIM to operate on any configured IP interfaces.
  • Page 225 Usage Example: To configure PIM settings for IP interface “System”: DES-6500:4#config pim ipif System hello 35 jp_interval 70 state enabled Command: config pim ipif System hello 35 jp_interval 70 state enabled Success. DES-6500:4# enable pim Purpose Used to enable PIM function on the switch.
  • Page 226 Description Parameters Restrictions Usage Example: To display PIM settings as configured on the switch: Used to display PIM neighbor router table entries. show pim neighbor {ipif <ipif_name 12> | ipaddress <network_address>} This command will list current entries in the PIM neighbor table for a specified IP interface or destination router IP address.
  • Page 227 DES-6500:4#show pim neighbor Command: show pim neighbor PIM Neighbor Address Table Interface Name Neighbor Address Expire Time --------------- System Total Entries : 1 DES-6500:4# show pim Purpose Used to display current PIM configuration. Syntax show pim {ipif <ipif_name 12>} Description This command will list current PIM configuration settings for a specified IP interface or all IP interfaces.

  • Page 228: Ip Multicasting Commands

    The IP multicasting commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command show ipmc cache show ipmc Each command is listed, in detail, in the following sections. show ipmc cache Purpose Used to display the current IP multicast forwarding cache.
  • Page 229 Usage Example: To display the current IP multicast forwarding cache: DES-6500:4#show ipmc cache Command: show ipmc cache Multicast Source Address/ Group Protocol ------------------ 224.1.1.1 10.48.74.121/32 224.1.1.1 20.48.74.25 /32 224.1.2.3 10.48.75.3 /3 Total Entries: 3 DES-6500:4# show ipmc Purpose Used to display the IP multicast interface table.
  • Page 230 Usage Example To display the current IP multicast interface table: DES-6500:4#show ipmc Command: show ipmc Interface Name IP Address Multicast Routing --------------- --------------- ----------------- System 10.90.90.90 PIM-DM Total Entries: 1 DES-6500:4#...

  • Page 231: Md5 Configuration Commands

    <password> − An MD5 password of up to 16 characters. Restrictions Only administrator-level users can issue this command. Usage Example To configure an MD5 Key password: DES-6500:4#config md5 key 1 dlink Command: config md5 key 1 dlink Success. DES-6500:4# create md5 Purpose Used to create a new entry in the MD5 key table.
  • Page 232 Description Parameters Restrictions Usage Example To create an entry in the MD5 key table: DES-6500:4# create md5 key 1 dlink Command: create md5 key 1 dlink Success. DES-6500:4# delete md5 Purpose Syntax Description Parameters Restrictions Usage Example The delete an entry in the MD5 key table:...
  • Page 233 To display the current MD5 key: DES-6500:4#show md5 Command: show md5 MD5 Key Table Key-ID ------ ---------- dlink develop fireball intelligent Total Entries: 4 DES-6500:4# DES-6500...

  • Page 234: Ospf Configuration Commands

    The OSPF configuration commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command config ospf enable ospf disable ospf show ospf create ospf area delete ospf area config ospf area show ospf area create ospf host_route delete ospf host_route config ospf host_route...
  • Page 235 This command is used to configure the OSPF router ID. Parameters <ipaddr> − The OSPF router ID. Restrictions Only administrator-level users can issue this command. Usage Example To configure the OSPF router ID: DES-6500:4#config ospf router_id 10.48.74.122 Command: config ospf router_id 10.48.74.122 Success. DES-6500:4# DES-6500 Parameters md5 <key_id 1-255>] metric <value 1-65535>...
  • Page 236 Used to enable OSPF on the switch. enable ospf This command, in combination with the disable ospf command below, is used to enable and disable OSPF on the switch. none. Only administrator-level users can issue this command. Used to disable OSPF on the switch.
  • Page 237 Syntax show ospf {ipif <ipif_name 12> | all} Description This command will display the current state of OSPF on the switch, divided into the following categories: Parameters ipif <ipif_name 12> - Enter the name of the ip interface to view the ospf settings for.
  • Page 238 Usage Example: To show OSPF state: DES-6500:4#show ospf Command: show ospf OSPF Router ID : 10.1.1.2 State : Enabled OSPF Interface Settings Interface IP Address ------------ ------------------ --------- System 10.90.90.90/8 0.0.0.0 Total Entries : 3 OSPF Area Settings Area ID --------------- 0.0.0.0...
  • Page 239 Total Entries : 0 OSPF Host Route Settings Host Address Metric --------------- 10.3.3.3 Total Entries : 1 DES-6500:4# create ospf area Purpose Used to configure OSPF area settings. Syntax create ospf area <area_id 0.0.0.0-255.255.255.255> type [normal/stub] {stub_summary [enabled/disabled]/metric <value>}] Description This command is used to create an OSPF area and configure its settings.
  • Page 240 DES-6500:4#create ospf area 10.48.74.122 type normal Command: create ospf area 10.48.74.122 type normal Success. DES-6500:4# delete ospf area Purpose Used to delete an OSPF area. Syntax delete ospf area <area_id> Description This command is used to delete an OSPF area.
  • Page 241 <value> − The OSPF area stub default cost. Restrictions Only administrator-level users can issue this command. Usage Example To configure an OSPF area’s settings: DES-6500:4#config ospf area 10.48.74.122 type stub stub_summary enabled metric 1 Command: config ospf area 10.48.74.122 type stub stub_summary enabled metric 1 Success.
  • Page 242 <value> − A metric between 1 and 65535, which will be advertised. Restrictions Only administrator-level users can issue this command. Usage Example To configure the OSPF host route settings: DES-6500:4#create ospf host_route 10.48.74.122 area 10.1.1.1 metric 2 Command: create ospf host_route 10.48.74.122 area 10.1.1.1 metric 2 Success.
  • Page 243 Restrictions Only administrator-level users can issue this command. Usage Example To delete an OSPF host route: DES-6500:4#delete ospf host_route 10.48.74.122 Command: delete ospf host_route 10.48.74.122 Success. DES-6500:4# config ospf host_route Purpose Used to configure OSPF host route settings.
  • Page 244 Usage Example To configure an OSPF host route: DES-6500:4#config ospf host_route 10.48.74.122 area 10.1.1.1 metric 2 Command: config ospf host_route 10.48.74.122 area 10.1.1.1 metric 2 Success. DES-6500:4# show ospf host_route Purpose Syntax Description Parameters Restrictions Usage Example: To display the current OSPF host route table:...
  • Page 245 Restrictions Only administrator-level users can issue this command. Usage Example: To create an OSPF area aggregation: DES-6500:4#create ospf aggregation 10.1.1.1 10.48.76.122/16 lsdb_type summary advertise enabled Command: create ospf aggregation 10.1.1.1 10.48.76.122/16 lsdb_type summary advertise enabled Success. DES-6500:4#...
  • Page 246 DES-6500:4#delete ospf aggregation 10.1.1.1 10.48.76.122/16 lsdb_type summary Command: delete ospf aggregation 10.1.1.1 10.48.76..122/16 lsdb_type summary Success. DES-6500:4# config ospf aggregation Purpose Used to configure the OSPF area aggregation settings. Syntax config ospf aggregation <area_id> <network_address> lsdb_type [summary] advertise [enabled/disabled] Description This command is used to configure the OSPF area aggregation settings.
  • Page 247 <area_id> − The OSPF area ID. Parameters Restrictions none. Usage Example To display OSPF area aggregation settings: DES-6500:4#show ospf aggregation Command: show ospf aggregation OSPF Area Aggregation Settings Area ID Aggregated Network Address Type ------------ --------------------- 10.1.1.1 10.1.1.1...
  • Page 248 DES-6500:4#show ospf lsdb Command: show ospf lsdb Area LSDB Type ----------- -------------- 0.0.0.0 RTRLink 0.0.0.0 Summary 1.0.0.0 RTRLink 1.0.0.0 Summary 1.0.0.0 Summary ASExtLink Total Entries: 5 DES-6500:4# show ospf neighbor Purpose Syntax Description Parameters Restrictions Usage Example To display the current OSPF neighbor router table:...
  • Page 249 (xxx.xxx.xxx.xxx) that uniquely identifies the OSPF area in the OSPF domain. <neighbor_id> − The OSPF router ID for the neighbor. This is a 32-bit number in the form of an IP address (xxx.xxx.xxx.xxx) that uniquely identifies the remote area’s Area Border Router. Restrictions none. DES-6500...
  • Page 250 Usage Example To display the current OSPF virtual neighbor table: DES-6500:4#show ospf virtual_neighbor Command: show ospf virtual_neighbor Transit Area ID --------------- ---------------- 10.1.1.1 DES-6500:4# config ospf ipif Purpose Used to configure the OSPF interface settings. Syntax config ospf ipif <ipif_name> {area <area_id>/priority <value 0- 255>/hello_interval <sec 1-65535>/dead_interval <sec 1-...
  • Page 251 65,535 that is representative of the OSPF cost of reaching the selected OSPF interface. The default metric is 1. Restrictions Only administrator-level users can issue this command. Usage Example To configure all of the OSPF interfaces on the switch with a single group of parameters: DES-6500...
  • Page 252 DES-6500:4#config ospf all state enabled Command: config ospf all state enabled Success. DES-6500:4# show ospf ipif Purpose Used to display the current OSPF interface settings for the specified interface name. Syntax show ospf ipif {<ipif_name>} Description This command will display the current OSPF interface settings for the specified interface name.
  • Page 253 Usage Example To display the current OSPF interface settings, for a specific OSPF interface: DES-6500:4#show ospf ipif ipif2 Command: show ospf ipif ipif2 Interface Name: ipif2 Network Medium Type: BROADCAST Area ID: 1.0.0.0 Priority: 1 DR Address: 123.234.12.34 Hello Interval: 10...
  • Page 254 Usage Example: To display the current OSPF interface settings, for all OSPF interfaces on the switch: DES-6500:4#show ospf all Command: show ospf all Interface Name: System Network Medium Type: BROADCAST Area ID: 0.0.0.0 Priority: 1 DR Address: 10.42.73.10 Hello Interval: 10...
  • Page 255 <key_id> − A previously configured MD5 key. A value between 1 and 255 seconds can be entered. Restrictions Only administrator-level users can issue this command. Usage Example To configure the OSPF virtual interface settings: DES-6500:4#config ospf virtual_link 10.1.1.2 20.1.1.1 hello_interval 10 Command: config ospf virtual_link 10.1.1.2 20.1.1.1 hello_interval 10 Success. DES-6500:4#...
  • Page 256 DES-6500:4#create ospf virtual_link 10.1.12 20.1.1.1 hello_interval 10 Command: create ospf virtual_link 10.1.12 20.1.1.1 hello_interval 10 Success. DES-6500:4# delete ospf virtual_link Purpose Syntax Description Parameters Restrictions Usage Example: To delete an OSPF virtual interface from the switch: DES-6500:4#delete ospf virtual_link 10.1.12 20.1.1.1 Command: delete ospf virtual_link 10.1.12 20.1.1.1...
  • Page 257 Area Border Router. This is the router ID of the neighbor router. Restrictions none. Usage Example: To display the current OSPF virtual interface configuration: DES-6500:4#show ospf virtual_link Transit Virtual Area ID Neighbor Router --------------- ------------------------- ----------- 10.0.0.0...

  • Page 258: Jumbo Frame Commands

    Used to enable the jumbo frame function on the switch. enable jumbo_frame This command will allow ethernet frames larger than 1518 bytes to be processed by the switch. The maximum size of the jumbo frame may not exceed 9K. None.
  • Page 259 DES-6500:4#enable jumbo_frame Command: enable jumbo_frame Success. DES-6500:4# show jumbo_frame Purpose Used to show the status of the jumbo frame function on the switch. Syntax show jumbo_frame Description This command will show the status of the jumbo frame function on the switch.

  • Page 260: Command History List

    Each command is listed, in detail, in the following sections. Purpose Syntax Description Parameters Restrictions Example usage To display all of the commands in the CLI: DES-6500:4#? clear clear arptable clear counters clear fdb clear log config 802.1p default_priority config 802.1p user_priority config 802.1x auth_mode...
  • Page 261 This command will display the command history. Parameters None. Restrictions None. Example usage To display the command history: DES-6500:4#show command_history Command: show command_history ? show show vlan config router_ports vlan2 add 1:1-1:10 config router_ports vlan2 add config router_ports vlan2 config router_ports...
  • Page 262 DES-6500:4#config command_history 20 Command: config command_history 20 Success. DES-6500:4#...

  • Page 263: Technical Specifications

    MAC Address Learning: Automatic update. Forwarding Table Age Max age: 10 - 1000000 seconds. Time: Default = 300. Standard DES-6500 ECHNICAL Performance General IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3ab 1000BASE-T Gigabit Ethernet IEEE 802.1 P/Q VLAN IEEE 802.3x Full-duplex Flow Control...
  • Page 264 Protocols Data Transfer Rates: Ethernet Fast Ethernet Gigabit Ethernet Fiber Optic Topology Network Cables General IEEE 802.3 Nway auto-negotiation CSMA/CD Half-duplex 10 Mbps 100Mbps 1000Mbps SFP (Mini GBIC) Support IEEE 802.3z 1000BASE-LX (DEM-310GT transceiver) IEEE 802.3z 1000BASE-SX (DEM-311GT transceiver) IEEE 802.3z 1000BASE-LH (DEM-314GT transceiver) IEEE 802.3z 1000BASE-ZX (DEM-315GT transceiver) Star UTP Cat.5, Cat.5 Enhanced for 1000Mbps...

  • Page 265: International Offices

    Australia 1 Giffnock Avenue, North Ryde, NSW 2113 Australia TEL: 61-2-8899-1800 FAX: 61-2-8899-1868 URL: www.dlink.com.au India D-Link House, Kurla Bandra Complex Road, Off CST Road, Santacruz (East), Mumbai - 400098. India TEL: 91-022-26526696/56902210 FAX: 91-022-26528914 URL: www.dlink.co.in Middle East (Dubai) P.O.Box: 500376...

Table of Contents