Other Features; Identification Of Parts - Midea MDDP-30DEN7-QA3 Owner's Manual

CONTROL PADS ON THE DEHUMIDIFIER
Display
9
Shows the set % humidity level from 35% to 85% or auto
start/stop time (0~24) while setting, then shows the actual
( 5% accuracy) room % humidity level in a range of 30%
RH(Relative Humidity) to 90%RH(Relative Humidity).
Error Codes and Protection Code:
AS - Humidity sensor error--Unplug the unit and plug it back
in. If error repeats, call for service.
ES - Tube Temperature sensor of the evaporator error-- Unplug
the unit and plug it back in. If error repeats, call for service.
P2 - Bucket is full or bucket is not in right position-- Empty
the bucket and replace it in the right position.(only available for
the unit with no pump feature.)

Other features

Bucket Full Light
Glows when the bucket is ready to be
emptied.
Auto Shut Off
The dehumidifier shuts off when the bucket is full,
or when the bucket is removed or not replaced in
the proper position. For some models the fan
motor will continue operating for 30 seconds.
Auto Defrost
When frost builds up on the evaporator coils, the
compressor will cycle off and the fan will continue
to run until the frost disappears.
Wait 3 minutes before resuming operation
After the unit has stopped, it can not be restart
opertation in the first 3 minutes. This is to protect
the unit. Operation will automatically start after
3 minutes.
Check filter feature
The system starts to count the time once the fan
motor operates. The check filter feature can be
only activated when the accumulated operation
time achieves 250 hours or more. The Reset
light(Clean filter indicator light) flashes at one time
per second, after finishing clean the air filter, press
the Filter pad and the Reset light(Clean filter indicator
light) goes off.
Auto-Restart
If the unit breaks off unexpectedly due to the power cut,
it will restart with the previous function setting automa-
tically when the power resumes.
P2- Bucket is full -- Empty the bucket.(only
available for the unit with pump feature.)
Eb - Bucket is removed or not in right position-- Replace the
bucket in the right position.(only available for the unit with
pump feature.)
Setting the Timer
When the unit is on, first press the Timer
button, the Timer Off indicator light
illuminates. It indicates the Auto Stop
program is initiated. Press it again the
Time On indecator light illuminates.It
indicates the Auto Start is initiated.
When the unit is off, first press the Timer
button, the TIMER ON indicator light
illuminates. It indicates the Auto Start
program is initiated. Press it again the
Time Off indecator light illuminates.It
indicates the Auto Stop is initiated.
Press or hold the UP or DOWN pad to
change the Auto time by 0.5 hour incre-
ments, up to 10 hours, then at 1 hour
increments up to 24 hours. The control
will count down the time remaining until
start.
The selected time will register in 5 seconds
and the system will automatically revert
back to display the previous humidity
setting.
When the Auto start & Auto stop times are
set, within the same program sequence,
TIMER ON OFF indicator lights illuminate
identifying both ON and OFF times are
now programmed.
Turning the unit ON or OFF at any time or
adjusting the timer setting to 0.0 will cancel
the Auto Start/Stop function.
When LED display window displays the
code of P2, the Auto Start/Stop function
will also be cancelled.
12
CONTROL PADS ON THE DEHUMIDIFIER
Identification of par ts
Front
Control panel
1
Panel
2
3 Water bucket
4 Water level window
Handle (both sides)
5
Rear
Continuous drain hose outlet
1
Caster
2
3 Power Cord and plug
Power cord buckle (placed in the water bucket,
4
used only when storing the unit. Installed as
shown Fig.3a))
5 Pump drain hose outlet(some models without)
6 Air outlet grille
7 Air filter
NOTE: All the pictures in the manual are
for explanation purposes only. The actual
shape of the unit you purchased may be
slightly different, but the operations and
functions are the same.
Accessories:(placed in the water bucket of the unit)
pump drain hose(1pc) (only for the unit with pump featrue)
power cord buckle(1pc)
1
2
3
4
1
2
3
Fig.3
Insert the power cord buckle
into the unit.
female threaded end(1pc)(on some models)
13
5
Fig.2
6
7
4
5
Fig.3a