Chamberlain door opener Owner's Manual page 19

3-BUTTON REMOTE CONTROLS
Your 315MHz Security✚ ® or dip switch remote control can be
programmed to operate as a 3-button wireless control station:
the large button will open the door, the middle button will
close the door, and the third button will stop the door's
movement. You may set up this feature as follows:
1. To enter programming press the RADIO button on the logic
board (the RADIO LED will light).
2. To program the OPEN button to a remote control press the
OPEN button on the logic board. The RADIO LED will flash and
then stay on solid. Then press the corresponding button on the
remote control. The RADIO LED on the logic board will flash,
this confirms that the remote control has been programmed.
(By programming the remote control you use 1 channel of the
23 channels on the radio receiver.)
3. To program the CLOSE button to a remote control press the
CLOSE button on the logic board. The RADIO LED will flash
and then stay on solid. Then press the corresponding button
on the remote control. The RADIO LED on the logic board will
flash, this confirms that the remote control has been
programmed. (By programming the remote control you use 1
channel of the 23 channels on the radio receiver.)
4. To program the STOP button to a remote control, press the
STOP button on the logic board. The RADIO LED will flash and
then stay on solid. Then press the corresponding button on the
remote control. The RADIO LED on the logic board will flash,
this confirms that the remote control has been programmed.
(By programming the remote control you use 1 channel of the
23 channels on the radio receiver.)
5. After learning remote controls press the RADIO button on the
logic board (LED will turn off). NOTE: If no activity within 30
seconds the radio will automatically exit programming mode.
OPEN
Open
Close
CLOSE
Stop
STOP
P R O G R A M M I N G
Ø14LGØ657–A Ø14GPØ657–A
P4
E1
C18
R29
C11
D3Ø2
X1 P1Ø
C17
D1
K3
EDGE
POWER
D22
OPEN
D2Ø D19
J1 J3ØØ TIMER
DEFEAT
OLS D25
D17
R8
MID D24
MAS D28
CLOSE
D21
SLS D26
D23
4
D16
EYES
CLS D27
D15
P7 MRT MID TIMER
D13 D1
EDGE
STOP
D22 OPEN
D2Ø
TIMER
RADIO 1 2 3 ENABLE
D36
CLOSE
D21
RELAY A
D13
STOP
C77
RELAY B
D35
T TS
C73
E2 FSTS
D1 DIAG
L1
C2
SBC
B2 PROG
L5
(B2 C2 D1 E2)
FAILSAFE
S8 NON FAILSAFE
D14
P6
REMOTE CONTROL PROGRAMMING FEATURE
Program Remote Controls from the 3-button control station
(3BCS).
Requires Firmware Version 4.6 or higher and a 3BCS with the
MAS connected to the control board.
This feature allows the user to add additional remote controls from
the 3BCS. By default the remote control learn option is off.
NOTE: Requires access to the operator electrical box to enable or
disable this feature.
To turn this feature on:
1. Turn the SELECTOR DIAL to PROG.
2. Press and release the RADIO button. The RADIO LED will be lit.
3. Press and release the MID button. The RADIO LED will flash
quickly 6 times.
4. Press and release the RADIO button. The RADIO LED will turn
off.
5. Return the SECTOR DIAL to the desired wiring type.
To add remote controls from the 3BCS:
1. With the door in the fully closed position (close limit activated),
press and hold STOP.
2. While holding STOP, press and hold CLOSE.
3. While holding STOP and CLOSE, press and hold OPEN.
4. Release all three buttons once the MAS LED has lit.
5. Learn a remote control by one of the following methods:
a. Programming a standard single button/single function
remote control, push and hold the remote control button
until the MAS LED goes out. Repeat steps 1 through 4 to
add additional remote controls.
b. Programming a 3-button/three function remote control
(open/close/stop), first push the button on the 3BCS
(example: OPEN) and then press and hold the button on the
remote control (example: large button) that you want to
correspond with the selected (example: OPEN) command
until the MAS LED flashes and goes out. Repeat steps 1
C3Ø
through 4 to add additional buttons (close and stop).
D31
D7
D6
D5
To turn this feature off:
C25 D4
24V
AC 14
24V
1. Turn the SECTOR DIAL to PROG.
AC 13
TIMER
DEFEAT 12
2. Press and release the RADIO button. The RADIO LED will be lit.
CMN 11
MAS 10
EYES 9 3. Press and release the MRT button. The RADIO LED will flash
EDGE 8
quickly 3 times.
OPEN 7
CLOSE 6
4. Press and release RADIO button. The RADIO LED will turn off.
STOP 5
CMN 4
5. Return SELECTOR DIAL to desired wiring type.
3
2
NOTE: Restoring the operator to Factory Default (see "RESETTING
SBC 1
P1
F1
D34
FACTORY DEFAULTS") will also disable this feature. The remote
controls will still be learned.
19