Table of Contents
Advertisement
Available languages
Available languages
Picture 4
• Remove the glass by gently
pulling it out of the door frame
(
Picture
5)
1
2
3
Picture 6
•
After cleaning the glass re-
assemble the parts in the
reverse order of removal.
• ON ALL GLASES LOW-E
sign must be properly readable
and must be positioned on the
left corner of the door, close to
the left side hinge. In this way
st
the printed surface of the 1
glass will remain INSIDE the
door.
SELF-CLEANING OVEN WITH CATALYTIC
- according to the model -
Special self-cleaning panels covered in a micro-porous coating
are available as optional extras for all models. If they are fitted,
the oven no longer needs to be cleaned by hand.
The fat that is splattered onto the sides of the oven during roasting
is eliminated by the microporous coating which breaks the fat
down by catalysis and transforms it into gas.
Excessive splattering may nevertheless block the pores and
therefore hinder self-cleaning. The self-cleaning capacity may be
restored by switching on the empty oven to maximum for about
10-20 minutes.
Do not use abrasive products, metal cleaning wads, sharp objects,
rough cloths, or chemical products and detergents that may
permanently damage the catalytic lining.
It is a good idea to use deep roasting trays to roast fatty foods
such as joints of meat etc. and to put a tray underneath the grill
to catch surplus fat.
If the walls of the oven are so thickly coated in grease that the
catalytic lining is no longer effective remove surplus grease with
a soft cloth or sponge soaked in hot water.
The lining must be porous for self-cleaning to be effective.
N.B.: All catalytic linings currently on the market have a working
life of about 300 hours. They should therefore be replaced after
about 300 hours.
CLEANING THE OVEN : PYROL YSIS
- according to the model -
Pyrolysis is a cleaning method that uses high temperatures to
destroy dirt.
The resulting smoke is cleaned by the passage of a catalyser.
The oven door is provided with a safety lock that prevents it being
opened during pyrolysis due to the necessity of high temperatures.
The pyrolysis cycle may result in a slight odour in the kitchen
which will be more or less noticeable depending on the latter's
aeration.
• Remove the top metallic cover
by pulling it
upwards. Picture
(
Picture 5
• *For
Pyrolytic
ovens, please
nd
rd
remove also 2 and 3 glasses .
(
Picture 6)
Picture 7
IMPORTANT :
Before carrying out pyrolysis:
4)
• Take all accessories out of the oven as they will be damaged
in the high pyrolysis temperatures;
• Clean away all excess food spills or large scraps of food
which would take too long to be destroyed. Effectively, large
amounts of grease may catch fire under the intense heat
emitted by pyrolysis.
• Close the oven door.
• If you have an hob top installed above the oven, never use
the gas burners or the electric plates during pyrolysis to
avoid excessive heating of the oven's control panel.
• It is strongly advised not to use detergents or any other
recommended product for cleaning ovens.
after the cycle pyrolysis
Open the oven door.:
Pyrolysis leaves a white residue on the oven walls.
Wait for the oven to cool completely then clean the inside
of the oven with a damp sponge to wipe off the residue.
Remarks:
•you will save energy by cleaning directly after cooking thus
making use of the residual heat in the oven.
The pyrolysis oven is fitted with a cooling fan which protects the
co n tro l pa ne l a nd el e ct ron i cs f ro m he a t da m ag e.
It begins when the pyrolysis cycle reaches high temperatures and
continues to rotate after the oven has been switch off until the
centre oven temperature is high.
Activation of the PYROLYSIS
. Rotate the function selector to the position P . On the display,
appears the indication " ECO " or " SUP "
. The preset time is 1.30 hrs, this can be varied from 1.30 hrs
(Eco mode) to 2 hrs (Sup mode) via the programmer (setting
button " + " or " - ").
If the oven is very dirty, it is recommend o increase the time to
2 hrs, if the oven is moderately dirty reduce the cleaning cycle
time to 1.30 hr.
. . It is possible to defer the start time of the pyroclean cycle by
changing the END time via the programmer.
. After few minutes, when the oven reaches a high temperature,
the door locks automatically.
. The pyroclean cycle can be stopped at any time by turning the
function selector back to '0' (the word OFF will be displayed for
3 seconds)
. Once the pyroclean cycle is finished, the pyrolysis will switch
off automatically. On the display appears the indication " END "
until the door is locked then "
. Y ou can turn the function selector back to " 0 " but if the temperaure
is still high, the "
door is locked.
SERVICE CENTRE
Before calling the Service Centre
If the oven is not working, we recommend that:
• you check that the oven is properly plugged into the power
supply.
If the cause of the fault cannot be detected:
disconnect the oven from the mains, do not touch the oven and
call the after sales service.
Before calling the Service Centre remember to make a note
of the serial number on the serial number specifications plate.
The oven is supplied with a guarantee certificate that ensures that
it will be repaired free of charge by the Service Centre whilst
under guarantee.
16 GB
"
" indication appears to inform that the
Advertisement
Table of Contents
