Titan 550xc Owner's Manual
  1. Manuals
  2. Brands
  3. Titan Manuals
  4. Paint Sprayer
  5. 550xc
  6. Owner's manual

Titan 550xc Owner's Manual

Airless sprayer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Do not use this equipment before reading this manual!
550
Model Numbers:
120V Skid, Bare
120V Skid, Complete
120V Low Rider , Bare
120V Low Rider , Complete
120V High Rider , Bare
120V High Rider , Complete
Printed in the U. S. A.
XC Airless Sprayer
765-2000
765-2001
765-2002
765-2003
765-2004
765-2005
Owner's Manual
For professional use only
NOTE: This manual contains important warnings
and instructions. Please read and retain for
reference.
1100 © 2000 Titan Tool Inc. All rights reserved. Form No. 313-1435, REV C

Advertisement

Table of Contents
loading

Related Manuals for Titan 550xc

Summary of Contents for Titan 550xc

  • Page 1 Please read and retain for 120V High Rider , Bare 765-2004 reference. 120V High Rider , Complete 765-2005 1100 © 2000 Titan Tool Inc. All rights reserved. Form No. 313-1435, REV C Printed in the U. S. A.

  • Page 2: Table Of Contents

    PSI/221BAR fluid pressure. • Use extreme caution when using materials with a flashpoint below 70° F (21° C). Flashpoint is the temperature that a fluid can produce enough vapors to ignite. © Titan Tool Inc. All rights reserved.
  • Page 3 • Wear clothing to keep paint off skin and hair. NOTE: Do not use more than 50 feet of extension cord. If you need to paint further than 100 feet from your power source, use more paint hose, not more extension cord. © Titan Tool Inc. All rights reserved.

  • Page 4: General Description

    8. Plug the power cord into a properly grounded outlet. paint. 9. Increase the pressure slowly until paint is coming through the return hose. © Titan Tool Inc. All rights reserved.

  • Page 5: Operating The Spray Gun

    12. Lock the gun by turning the gun trigger lock to the locked position. © Titan Tool Inc. All rights reserved.

  • Page 6: Spraying

    Shrubs next to houses should be tied back and covered with a canvas cloth. The cloth should be removed as soon as possible. Titan gun extensions are extremely helpful in these situations. Avoid arcing or holding the gun at an angle. This will result in an uneven finish.

  • Page 7: Cleanup

    5. Move the ON/OFF switch to the ON position. for recommendations. 6. Tilt the siphon tube above the material container and allow 5. If you have any further questions concerning your TITAN the unit to pump itself dry through the return tube. Airless Sprayer, call TITAN: 7.

  • Page 8: Spray Gun Maintenance

    (8 ounce bottles) Handle 700-912 ...Case of 12 (1 quart bottles) NOTE: For more detail, part number information, and assembly drawings at larger scale, please see the LX -80 Professional Airless Gun Owner's Manual (#313-012). © Titan Tool Inc. All rights reserved.
  • Page 9 500-056 ...Four gun manifold 520-046 ...Tip Filter Retainer 490-005 ...Swivel Union, 1/4" M x 1/4" F 490-032 ...Swivel Union, 1/4" M x 3/8" F 490-007 ...Retaining Nut Adapter 730-235 ...High Pressure Fl. Gauge 757-120 ...Ball valve © Titan Tool Inc. All rights reserved.

  • Page 10: Troubleshooting

    2. Needle assembly out of adjustment 2. Adjust 3. Dirty gun 3. Clean Gun does not spray 1. No paint 1. Check fluid supply 2. Plugged filter or tip 2. Clean 3. Broken needle in gun 3. Replace © Titan Tool Inc. All rights reserved.

  • Page 11: Spray Patterns

    Remove restrictions in system; clean tip screen if filter is used. Round pattern 1. Worn tip 1. Replace tip. 2. Fluid too heavy for tip 2. Increase pressure. Thin material. Change nozzle tip. © Titan Tool Inc. All rights reserved.

  • Page 12: Français

    • Tous les accessoires doivent être homologués pour une pression égale ou supérieure à 3 200 lb/po2 / 221BAR. Cela s'applique, entre autres, aux têtes de pulvérisation, aux accessoires du pistolet et aux flexibles. © Titan Tool Inc. Tous droits réservés.
  • Page 13 • Ne jamais pulvériser lorsqu'il vente. peinture plus long et non une rallonge plus • Porter des vêtements pour protéger la peau et les longue. cheveux contre tout contact avec la peinture. © Titan Tool Inc. Tous droits réservés.

  • Page 14: Español

    Consulte el manual del motor • Todos los accesorios deben tener una capacidad de 3200 para obtener información completa de seguridad. lb/pulg2 / 221BAR o mayor. Esto incluye las boquillas de atomizador, pistolas, extensiones y mangueras. © Titan Tool Inc. Todos los derechos reservados.
  • Page 15 El enchufe se debe enchufar en una toma de corriente que se haya instalado y conectado a tierra debidamente, de acuerdo con todos los códigos y estatutos locales. © Titan Tool Inc. Todos los derechos reservados.

  • Page 16: Parts Lists And Service Instructions

    Parts Lists and Service Instructions Main Assembly Replacement Labels NOTE: Siphon down tube Part # Description Quantity for use with High Rider only. 700-1016 Front cover label .............1 313-175 "Warning/Attention" (label In French).....1 313-1484 Wraparound 550XC label........1 © Titan Tool Inc. All rights reserved.

  • Page 17: Motor Assembly

    6. Inspect the motor field assembly. If damaged, replace. 7. To install the motor housing, reverse steps 1–5 above and steps 1–7 of the “Replacing the Armature” procedure. © Titan Tool Inc. All rights reserved.

  • Page 18: Gear Box Assembly

    Lock washer........3 700-593 Thrust washer .........1 700-197 Pressure transducer assembly ..1 765-057 Thrust washer .........2 700-162 Pressure control board ....1 730-360 Crankshaft ........1 700-139 Screw ..........4 765-046 Pinion gear........1 700-148 Potentiometer mount .......1 © Titan Tool Inc. All rights reserved.
  • Page 19 PLUG 4. Back off screw. Hold the brush wire and remove the motor brush (26). ELECTRICAL CONTROL ASSEMBLY 110V -- 440; 550 5. Inspect the motor brush. If damaged, replace. © Titan Tool Inc. All rights reserved.

  • Page 20: Fluid Section Assembly

    Assembly” parts list) and pull it down and out of the foot valve (22). 5. Remove the siphon assembly by pulling it down and out of the foot valve (22). 4. Tilt the pump back for easy access to the fluid section. © Titan Tool Inc. All rights reserved.

  • Page 21: Siphon Assembly

    22. Slide the assembled pump housing with the piston assembly onto the connecting rod and secure with the screws (7). Be certain that the outlet hole is facing towards the pump motor. © Titan Tool Inc. All rights reserved.

  • Page 22: Filter Block Assembly

    (excludes items 3, 4, 17, and 24) ..1 700-890 O-ring tool (not shown) ......1 NOTE: When using “HOT” solvents, replace o-ring item#10 with optional PTFE o-ring P/N 700- 897. Install using the o-ring tool P/N 700-890. © Titan Tool Inc. All rights reserved.

  • Page 23: Low Rider Frame Assembly

    700-674 End cap..........4 704-092 Leg, left (includes items 2 and 4) ..1 700-781 Drip cup ...........1 700-069 Screw ..........2 700-761 Cord wrap ........1 704-091 Leg, right (includes items 2, 5, and 6) .....1 © Titan Tool Inc. All rights reserved.

  • Page 24: Warranty

    Warranty Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment covered by this warranty is free from defects in material and workmanship. Titan’s obligation under this warranty is limited to replacing or repairing without charge those parts which, to Titan’s reasonable satisfaction, are shown to be defective within...

Table of Contents