Page 1
Installation Instructions Heritage Wall-Mount Range Hoods HWHE30/36/48; HWHP30/36/48 ® APPROVED FOR USE WITH ALL DACOR RANGES AND COOKTOPS. TESTED IN ACCORDANCE WITH THE LATEST EDITION OF ANSI/UL 507 STANDARD FOR ELECTRIC FANS AND CAN/CSA-C22.2 NO. 115 STANDARD FOR FANS AND VENTILATORS.
Use common sense and caution when installing the hood. WARNING • Contact Dacor Customer Assurance about issues you cannot resolve (contact information on previous page). Hazards or unsafe practices that COULD result in severe personal injury or death.
WARNING • Use the hood only as outlined in this manual. Do NOT use the hood to vent hazardous/explosive materials or vapors. If you have questions, contact Dacor (contact info on Pg. 1). • If you receive a damaged product, immediately contact your dealer/builder. Do not install/use a damaged hood.
Product Specifications Dimensions (Electrical/Ductwork Connections) Connect electrical wires and ductwork through the top or rear of the hood. Before installing the hood, mark the access holes according to the diagrams below. (Tolerances: ±1/16” unless otherwise stated.) Dimensions: Top Electrical Access Holes (HWHP, HWHE) Model 1 1/2 in.
Page 7
Product Specifications Dimensions Tolerances: ±1/16” unless otherwise stated. Single Blower: Single Blower: HWHP 30, 36 Series HWHE 30, 36 Series Dual Blower: Dual Blower: HWHP 48 Series HWHE 48 Series HWHP Hood Dimensions HWHE Hood Dimensions Model Model 3012 29 7/8” (75.9 cm) 3012 29 7/8”...
Preparation and Setup Meeting Installation Requirements • See the diagram below: Top/Rear Electrical Access Holes for wire hole locations inside the hood. • See Wiring Diagrams at the end of this document. WARNING Observe local ordinances regarding all facets of the project during planning and installation.
• On dual-exhaust models, the two 8” exhausts may be gered 45° angles are better than one sharp 90° angle). merged into one 10” duct using Dacor transition kit • Keep turns as far away from the hood exhaust as pos- AHT10.
Preparation and Setup • Support the weight of the ducting with sheet-metal HWHP, HWHE Weight screws as needed. 3012 51 lbs. (23 kg) • To prevent backdraft, a damper at the duct outlet may be required. 3018, 3612 53 lbs. (24 kg) 3618 57 lbs.
Installation Instructions Marking the Centerlines IMPORTANT Users of the dual-exhaust format will need to install the These measurements and marks are for centering and leveling the hood, marking the duct cutouts, and installing AHT10 Dual-to-Single Transition Kit. (See the section Using the Dual-to-Single Transition Kit #AHT10 on Page the holding brackets (which brackets temporarily support 12 for installation instructions.)
Installation Instructions Installing the Holding Brackets, Rotating the Blower(s) for Rear cont. Exhaust Perform this procedure before you hang the hood. Holding-Bracket Centerline Distance WARNING HWHP, HWHE 3012, 3018 12 1/2 in (31.8 cm) • Only install the hood if the electrical service provided meets the hood’s specifications.
Page 14
Installation Instructions Rotating the Blower(s) for Rear 3. Unscrew the cable clamp(s), and remove the hardware that holds the blower and L-bracket (previous graphic). Exhaust, cont. 4. Detach the blower and plate, and place them nearby. Orientating the Blower/Vent L-Brackets The images in this section were chosen to illustrate the intended information and may not exactly represent the 1.
Installation Instructions Rotating the Blower(s) for Rear Assembling the Filters Exhaust, cont. Filters are boxed separately and must be assembled during installation. All needed knobs and hardware are included Orientating the Blower(s) with the filters. For correct orientation, ensure the top of the filter faces up. The blower(s) must be correctly positioned.
• Rear vent: Models: 3018, 3618, 4818 On dual-exhaust models, the two 8” duct exhausts can be transitioned into one 10” duct. Assemble the Dacor transition kit #AHT10 (sold separately) before you hang the hood. This transition kit fits over the top/rear ventilation exits.
Installation Instructions Hanging the Hood WARNING Hanging the range hood requires two people. Do not lift the hood unassisted. IMPORTANT Take care not to scratch/damage the hood. 1. Remove the plastic film from the hood. IMPORTANT Rear-Vent Configuration Hanging slots in the hood back engage the holding brack- ets to support the hood temporarily during installation.
Installation Instructions Hardwiring the Hood, cont. 5. (If needed) Mark the top of the hood if the configuration calls for the hood to be secured at the top. 6. Remove the hood from the wall. Not used 7. Drill the pilot or anchor holes. (If using anchors, insert Neutral (white) them into the anchor holes.) Ground (green)
Installation Instructions WARNING • Do not ground the circuit to a gas line. • Do not ground the circuit to a hot water pipe. • Insulated water lines must be jumped to assure continuity to the ground. (See below.) To house circuit Separate No.
3. Verify that the electrical connections are correctly done. 4. Perform the Verify the Setup procedure again. IMPORTANT If the hood still does not work, contact Dacor Distinctive Service: (800) 793-0093 x2822. Do not try to repair the appliance yourself. Dacor is not responsible for service required to correct a faulty installation.