CAME BX-243 Installation Manual
Hide thumbs Also See for BX-243:

Advertisement

Quick Links

AUTOMATION SYSTEMS
FOR SLIDING GATES
FA 00669 - EN
INSTALLATION MANUAL
BX-243
EN
English

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BX-243 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for CAME BX-243

  • Page 1 AUTOMATION SYSTEMS FOR SLIDING GATES FA 00669 - EN INSTALLATION MANUAL BX-243 English...
  • Page 2: Read Carefully

    • THIS PRODUCT SHOULD ONLY BE USED FOR THE PURPOSE FOR WHICH IT WAS SUPERVISED OR GIVEN INSTRUCTIONS REGARDING USING THE OPERATOR BY A EXPLICITLY DESIGNED. ANY OTHER USE IS CONSIDERED DANGEROUS. CAME S.P.A. PERSON RESPONSIBLE FOR THEIR SAFETY • FREQUENTLY CHECK THE SYSTEM,...
  • Page 3: Legend Of Symbols

    Legend of symbols This symbol tells you to read the section with particular care. This symbol tells you that the sections concern safety issues. This symbol tells you what to say to the end-users. HE MEASUREMENTS UNLESS OTHERWISE STATED ARE IN MILLIMETERS Conditions of use Intended use The BX243 operator is designed to power sliding gates in residential and condominium settings.
  • Page 4: Description Of Parts

    Description of parts 1) Top cover 2) Motor 3) Transformer 4) Trap door to access manual release of gearmotor 5) Securing plate 6) Securing bolt 7) Securing nut and washer 8) Protective cover for electronic card 9) ZN2 electronic card 10)Card and battery rack support Dimensions (mm)
  • Page 5: Standard Installation

    Cable list and minimum thickness Length of cable Length of cable Length of cable Connection Type of cable 1 < 10 m 10 < 20 m 20 < 30 m Control panel power supply 230V 3G x 1,5 mm 3G x 2,5 mm 3G x 4 mm Flashing light 2 x 0,5 mm...
  • Page 6 Securing the plate and installing the assembly The following applications are only examples, as the space for installing the ratiomotor and accessories varies according to obstructions. It is thus up to the system installer to select the most suitable solution. - Dig a pit to the side of the gate (see measurements from diagram).
  • Page 7 Remove the form box (1), fi ll the pit around the cement block with soil (2) and unbolt the nuts and washers from the bolts (3). The securing plate must be clean, perfectly aligned and with the bolt threads completely on the surface. Insert the electric cables into the tubes until they exit about 400mm (4).
  • Page 8 - The following illustrations for the securing the rack, are just examples of applications. It is up to the installer to choose the best solution. Releasing the gearmotor (see paragraph on manual release). Rest the rack on the gearmotor pinion. Weld or secure the rack to the gate along its entire length.
  • Page 9 Adjusting the mechanical stops Adjusting the opening mechanical stops: - with the motor in release mode, fully open the gate. Activate the opening-microswitch, turning the white cam clockwise. Secure the cam by turning the screw. Opening-microswitch White cam Adjusting the closing endstop: - with the motor in release mode, fully close the gate.
  • Page 10: Control Board

    Control board General description Use 230V AC to power the electronic card using the L-N terminals, at All connections are protected by quick-fuses – see table. a max 50/60Hz frequency. Use 24V to power the command devices and accessories. Careful! F US E TA BL E The accessories cannot exceed 37W of overall power.
  • Page 11: Electrical Connections

    Electrical connections Gearmotor, endstop and encoder Description of the standard electrical connections for left-hand installations White Orange Brown Green White Orange Green 24V (DC) motor with Opening mi- Closing microswitch encoder croswitch Invert the gearmotor (M- Modifications to the electri- N) and (FA-FC) endstop cal connections for right-hand phases.
  • Page 12: Safety Devices

    Command and control devices Stop button (N.C. contact) - Gate stop button. Excludes automatic closing. For motion to resume, press the command button or the remote control button. Key selector and/or partial opening button (N.O. contact) - Partial gate opening for pedestrian access. Key selector and/or command button (N.O.
  • Page 13 «Open while closing»(N.C.) contact DF with DFI con- - input for EN 12978 compliant safety nections monitor devices such as sensitive edges. During card gate closing, opening the contact causes inversion of movement until gate is fully open; if not used, short circuit contact 2-C7.
  • Page 14: Warning Led

    Settings SETTING TRIMMER LIST: exceed the set level, the system intervenes by inverting the direction of motion. - «ACT.» Sets the waiting time while open. Once this time has elapsed, closing automatically takes place. The waiting - «RUN S.» Sets the amperometric sensitivity that controls the force time may be set from 1 to 150 seconds.
  • Page 15: Function Selector

    Function selector Default Setting 1 ON - Automatic Closing - The automatic closing timer activates at 6 ON - Maintained action - The gate works by keeping button pressed the end of the opening gate run. The pre-set time is adjustable, (one 2-3P opening button , and one 2-7 closing button).
  • Page 16 Activating the radio control  Connect the antenna’s RG58 cable. Cut off the main power supply, and remove any batteries.  Fit the AF board onto the electronic board. The electronic board recognizes the AF board only when the operator is powered up again.  Keep the PROG button on the electronic board pressed: the warning LED flashes.
  • Page 17 Connecting two coupled gearmotors having a single control With two coupled gearmotors, you can command only the opening (by button and/or radio control): the gate will close only in automatic closing mode. • Coordinate the direction of travel of the two gearmotors , by modifying the motor's rotation (invert the cables on terminals FA-FC and M-N).
  • Page 18: Periodic Maintenance

    Maintenance Periodic maintenance Periodic maintenance to be carried out by the end-user is as follows: wipe clean the glass surface of the photocells; check that the safety devices work properly; remove any obstructions. We suggest checking the state of lubrication and tightness of the anchoring screws on the operator. -To check the efficiency of the safety devices, move an object in front of the photocells when gate is closing.
  • Page 19: Troubleshooting

    Trouble shooting MALFUNCTIONS POSSIBLE CAUSES CHECK AND REMEDIES The gate will not • There is no power • Check that the power is up open nor close • The release door is open • Close the release door • The gearmotor is in release mode •...
  • Page 20: Demolition And Disposal

    ☞ CAME S.p.A. implements an EN ISO 14001 certified and compliant Environmental Management System at its plants, to ensure environmental protection. Please continue our efforts to protect the environment, something that CAME considers to be one of the foundations in developing its business and market strategies, simply by observing brief recommendations as regards disposal: DISPOSAL OF PACKAGING Packaging components (cardboard, plastic etc.) can be disposed of together with normal household waste without any difficulty, by simply...

Table of Contents