Panasonic AG-CX10 Operating Instructions Manual page 165

6
Remaining recording capacity and status of the memory card
Displays the remaining recording capacity and status of the memory card in card slot 1 or card slot 2.
≥ [0min] to [999min]: Remaining recording capacity (999 minutes or more is displayed as [999min])
j The display will flash when the remaining recording capacity becomes 2 minutes or less.
j The recording capacity available for simultaneous recording (recording capacity for the memory card of the 2 memory cards with less recording
capacity) is displayed when simultaneous recording is performed.
≥ [WP]: Write protected (the write protection switch of the memory card is set to the LOCK side)
≥ [END]: No remaining recording capacity (no remaining recording capacity on the memory card)
≥ [ERR]: A memory card that cannot record is inserted (the card is recognized but cannot record due to a format error, a card other than a memory
card being inserted, etc.)
≥ [!SDXC]: An SDXC memory card is not inserted in MOV recording/MP4 recording
≥ (No display): It is in one of the following conditions.
j A memory card has not been inserted.
j The memory card cannot be recognized.
j (For the )
CX10
The [NETWORK] menu → [NETWORK FUNC] → [NDI|HX] is set.
7
External equipment recording operation control status (<SDI OUT>/<HDMI> terminal)
Displays the control status of the recording start and recording stop on the external equipment connected to the <SDI OUT> terminal and the
<HDMI> terminal.
*1
≥ [ SDI] : Recording instruction is output to the output from the <SDI OUT> terminal.
*1
≥ [SDI] : Pause instruction is output to the output from the <SDI OUT> terminal.
≥ [ HDMI]: Recording instruction is output to the output from the <HDMI> terminal.
≥ [HDMI]: Pause instruction is output to the output from the <HDMI> terminal.
8
Special recording function
Displays the status of special recording function.
≥ [INTRVL]: The interval recording is stopped.
≥ [I-REC]: The interval recording is in progress. (Displayed in red)
9
2-slot function
Displays the setting status of the recording function using 2 memory cards.
It is displayed with a slanted line if it is in a condition that cannot perform 2-slot recording even if each function is enabled.
≥ [RELAY]: When the relay recording is enabled
≥ [SIMUL]: When the simultaneous recording is enabled
≥ [BACKGR]: When the background recording is enabled
≥ (No display): During standard recording
j (For the )
CX10
When set to the [NETWORK] menu → [NETWORK FUNC] → [NDI|HX], [NDI|HX] is displayed
10
Flash band compensation function
≥ [FBC]: Displayed when the flash band compensation function is operating.
11
Streaming status
Displays the streaming status.
≥ : When the unit is connected to a device to receive the streaming video, and the streaming video is distributed
(flashing): When the unit is being connected to a device to receive the streaming video
≥
≥ : When the streaming function is enabled, it is in condition to operate properly, and the streaming video is not distributed
≥ : When there is an error in the streaming function and cannot operate
≥ (No display): When the streaming function is disabled
12
Dynamic range stretcher function
≥ [DRS]: Displays when the dynamic range stretcher function is working.
13
Connection status of the wireless LAN/wired LAN
Displays the connection status of the wireless LAN or wired LAN.
≥ : When set to the wireless LAN and the ROP is not connected
: When set to the wireless LAN and the ROP is connected
≥
: When set to the wireless LAN and the wireless LAN is not operating properly
≥
*2
≥ : When set to the wired LAN and the ROP is not connected
*2
: When set to the wired LAN and the ROP is connected
≥
*2
: When set to the wired LAN and the wired LAN is not operating properly
≥
≥ (No display): When both the wireless LAN and the wired LAN are disabled
14
Power status
: Displays the remaining battery level while powered with the battery. (The battery status display will change as
→
while the remaining battery level gets lower. It will flash in red when the remaining battery level is zero.)
: Displayed when powered with the AC adaptor.
15
Audio level meter
Displays the audio level meter.
A white border is displayed in the position of the recording base level (12 dB).
: Displayed when audio cannot be recorded. (When super slow is enabled, etc.)
≥
16
Luminance of Y GET
Displays the luminance level in 0% through 109% when the Y GET function is operating.
17
Gain
Displays the gain value.
≥ [AGC]: Displayed when the auto gain control is operating.
≥ [SG]: Displayed when [SUPER GAIN] is working.
≥ [SGi]: Displayed when [SUPER GAINi] is working.
Chapter 7 Output and Screen Display — Screen status display
- 165 -
→ → → →