Triax TSR 1000 User Manual

Triax TSR 1000 User Manual

Digital satellite receiver fta

Advertisement

Quick Links

_______________________________________________________________
TRIAX TSR 1000
________________________________________________________________
Digital Satellite Receiver FTA
User Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TSR 1000 and is the answer not in the manual?

Questions and answers

Summary of Contents for Triax TSR 1000

  • Page 1 _______________________________________________________________ TRIAX TSR 1000 ________________________________________________________________ Digital Satellite Receiver FTA User Guide...
  • Page 2: Safety Precaution

    CAUTION: The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to "dangerous voltage" and to prevent from a risk of electric shock. WARNING: Do not use this STB where contact with or immersion in water is a possibility.
  • Page 3 Locating: Slots and openings in the cabinet are provided for ventilation to protect it from overheating. Do not block these openings or allow them to be blocked by placing the STB on a bed, sofa or other similar surface, nor should it be placed over a radiator or heat register.
  • Page 4: Table Of Contents

    1. Remote Control & Panel Description ... 3 1.1 Front Panel Description... 3 1.2 Rear Panel Description ... 4 1.3 Remote Control Description ... 5 2. Basic Operations... 6 2.1 Switch on STB ... 6 2.2 Standby Mode: ... 6 2.3 Channel +/-...
  • Page 5 3.5 Delete All ... 17 3.6 Restore channel list and settings... 17 3.7 Save channel list and settings ... 18 4. Installation ... 19 4.1 Antenna Setup... 19 4.2 Single Search ... 20 4.3 Multi Search... 21 4.4 TP Scan... 21 4.5 Satellite List ...
  • Page 6: Remote Control & Panel Description

    1. Remote Control & Panel Description 1.1 Front Panel Description POWER: Is used to switch between the working mode and the standby mode. Display (4-Digit/7-Segment): Displays the received channel number while operating and time while in standby mode. Remote Sensor: Detects the infrared signals from the remote control unit. VOL+/-: To change volume to move cursor, change numbers in the menu or to change the choice.
  • Page 7: Rear Panel Description

    1.2 Rear Panel Description IF OUT: The operation of another receiver at the same time is only possible Note: with limited channel selection. IF IN: RS-232: ANT IN: AC IN: POWER ON/OFF: VIDEO / AUDIO: TV SCART: TO TV: 10. VCR SCART: Remote Control &...
  • Page 8: Remote Control Description

    Remote Control & Panel Description 1.3 Remote Control Description...
  • Page 9: Basic Operations

    2. Basic Operations 2.1 Switch on STB Switch the [Device’s Main Power] switch on. you will set Language, First Audio, Second Audio, LNB Power, Antenna Setup and Multi Search. Frequently Asked Question Q: The power of my STB is on and it is running in TV mode but the TV screen shows nothing: A: Make sure the TV set has been set to the correct video input(not the TV channels).
  • Page 10: Channel Number

    2.5 Channel Number In TV/radio mode you can enter the channel number directly with your remote control unit and confirm the number with the OK button to change to the desired channel. 2.6 Mute Press the [Mute] button to mute the sound. On the screen an icon will be displayed to indicate the muted sound.
  • Page 11: Edit

    2.10 EDIT In TV mode, press the [EDIT] button to open the “TV Channel List” window. 2.11 Audio Track / Mode In TV mode, press the [Audio] button to open the audio mode window. Select the item you want to adjust with [Channel Up/Down] and change the value with [Volume Up/Down].
  • Page 12: Tv/Radio

    The [Red] button opens the detailed schedule of the marked channel. You can select an event with [Channel Up/Down] and display the event’s detailed description with [OK]. Press the [Green] button in the EPG menu display information of the actual event in the selected channel.
  • Page 13: Change Satellite

    Press [Yellow] button to open the SAT list. After selecting a satellite the channel list will be reduced to the channels of this satellite. Press [FAV] button to open FAV list. After selecting a favorite group the channel list will be reduced to the channels of this group.
  • Page 14: Sub

    2.19 SUB SUB(Subtitle): In “OSD Setting menu, use [Volume Up/Down] to select “On” or “Off”. If the current channel has subtitle information, it will be displayed if this function is “On”. If this function is “Off” subtitles won’t be displayed. 2.20 TXT Press [TXT] button in TV mode to open the teletext page.
  • Page 15: Channel

    3. Channel Press [Menu] in the TV/radio mode to enter the main menu. Press [Channel Up/Down] to select the channel item. Press [OK] to enter the selected item. In the channel menu: Press [Channel Up/Down] to select the wanted menu item among TV Channel List, Radio Channel List,...
  • Page 16: Favorite

    3.1.1 Favorite Press [FAV] to open the favorite window. You can select between 8 favorite groups with [Channel Press [OK] to assign the channel to a favorite group, press [EXIT] to exit favorite group. Press [OK] again to remove the channel from the marked favorite group.
  • Page 17: Tv Channel List Edit

    FTA: Sort channel by free and scrambled sequence. Free channels will be listed first and scrambled channels behind in the channel list. Lock: Unlocked channels are listed first end locked channels at the end. 3.1.4 TV Channel List Edit After pressing the [Yellow] button a window for entering the password will open.
  • Page 18: Find

    Selecting the name item with [OK] will display a button pad to show you how to edit the channel name. On the “Video PID”, “Audio PID” and “PCR PID” items you can input numbers to modify the item’s value. After modification select “Save” and press [OK] button to save the modified values and exit “Edit”...
  • Page 19: Radio Channel List

    3.2 Radio Channel List Basically the operation of “Radio Channel List” is same as “TV Channel List”, except that in the small channel window the radio Logo will be displayed. 3.3 Channel Setup When you enter the “Channel Setup” menu you will see a screen like beside: Startup Channel: Press [OK] to enter “Startup Channel”...
  • Page 20: Favorite Channel List Name

    3.4 Favorite channel list name When you enter “Favorite channel list name” menu with 8 favorite group will be displayed. Press [Red] or [OK] key on the RCU to rename favorite group with the [Number] buttons. After modification select “Save” and press [OK] to save the favorite group name and leave the edit mode.
  • Page 21: Save Channel List And Settings

    3.7 Save channel list and settings To save channel list and settings. Enter the password. The default password is “0000”. After entering the password correct a safety question will show up where you have to confirm first. 3. Select “Yes”, press [OK] to save current channel list to backup channel list.
  • Page 22: Installation

    4. Installation After selecting the installation menu you can see the window like beside. In “Installation” menu; Press [Channel Up/Down] to select menu items among Antenna Setup, Single Search, Multi Search, TP Scan, Satellite List, TP List and Satellite Guide. Press [OK] to enter the selected item.
  • Page 23: Single Search

    2Cascades Port1 / 2Cascades Port2 / 2Cascades Port3 / 2Cascades Port4 / 2Cascades Port5 / 2Cascades Port6 / 2Cascades Port7 / 2Cascades Port8 / 2Cascades Port9 / 2Cascades Port10 / 2Cascades Port11 / 2Cascades Port12 / 2Cascades Port13 / 2Cascades Port14 / 2Cascades Port15 / 2Cascades Port16.
  • Page 24: Multi Search

    4.3 Multi Search When you enter the “Multi Search” menu a window like the one beside will open. On “Satellite” item press [OK] to open the satellite list. Then press [Channel Up/Down] to move the highlight and press [OK] [MENU] to finish the selection. You can select several satellites in this menu.
  • Page 25: Satellite List

    When you press [Green] a safety question will be displayed for confirmation to delete the current transponder or not. If you select “Yes”, the current transponder will be deleted and the total number of transponders will be reduced. For existing transponders you also can use number buttons to modify the parameters of “TP Frequency”...
  • Page 26: Tp List

    Press [Green] button to open the “Add satellite” window. After pressing [Yellow] button you will be asked “Are you sure to delete?”. Select “Yes” to delete the marked satellite. Select “No” to cancel the operation. 4.6 TP List When you open the “TP List” menu you will see a window like the one beside.
  • Page 27: Satellite Guide

    Press [Green] button to open the “Add TP” menu. Here you can add a new TP and setup its parameters. Press [Yellow] button will open a dialog box asking you to confirm the deletion of the current TP. If you select “Yes”...
  • Page 28 Use the [Number] buttons to input the values of “Local Longitude”, “Local Latitude” and “Satellite Longitude”. Press [Volume Up/Down] to switch east or west in “Local Longitude” and “Satellite Longitude” or to switch north or south in “Local Latitude”. Highlight the “Start” item and press [OK]. In the lower part of the window the corresponding values for the antenna setting is displayed.
  • Page 29: System Setup

    5. System Setup When you open the “System Setup” menu a window like the one beside will be opened. In “System Setup” menu: Press [Channel Up/Down] to select menu items among Language, TV System, Time & Timer setting, OSD Setting, Parental Lock, LNB Power and RCU position switch.
  • Page 30: Tv System

    5.2 TV System When you enter the “TV System” menu you will see the screen like below: Display Mode is used to switch the display mode. You can select from Auto / PAL / PAL-N / PAL-M / NTSC3.58. Press [Volume Up/Down] to switch the desired mode.
  • Page 31 NOTE: If the current channel provides information, you will see the current time after you entered “Time” menu. If the channel doesn’t provide time information, you have to input the date and time information manually. The most channels support the time signal.
  • Page 32: Osd Setting

    When you select “Message”(reminding message) option in “Timer Service” then you can enter additional data: ♦ Wakeup Message: Press [Volume Up/Down] to select the category of the reminding message from Birthday, Anniversary and General. ♦ Wakeup Date: Use the [Number] buttons to input your wakeup date.
  • Page 33: Parental Lock

    5.5 Parental Lock You can set a password for anyone who wishes to operate the “Installation” menu. You can also set the password to lock channels. Below you find how to set and change the password. On “Parental Lock” press [OK] to open dialogue password.
  • Page 34: Rcu Position Switch

    5.7 RCU position switch This item can select the switch controller’s position. The position number you choose in this menu must be same as the switch controller’s setup, or the switch controller can not work correctly. Press [◄/►] to modify the change. Menu Operations...
  • Page 35: Tools

    6. Tools When you enter to “Tools” menu, you will see a screen like beside: In “Tools” menu: Press [Channel Up/Down] to select the wanted item among Information, Quick Setup, Game, Factory Default, Software Upgrade and SatcoDX Auto Programming. Press [OK] button to enter the selected item.
  • Page 36 Basic operation statement: Tetris Mark “Setup” and press [Volume Up/Down] to select the level (speed). Mark “Start” and press [OK] to start the game. Mark “Cancel” and press [OK] to leave the game. Play the game: ♦ Press [Volume Up/Down] to move the block left or right ♦...
  • Page 37: Factory Default

    ♦ Press [Volume Up/Down / Channel Up/Down] to position the round mark. ♦ Press [OK] to set your stone. ♦ Press [MENU] to quit the game and return to the game menu. 6.4 Factory Default When you press [OK] on the “Factory Default”...
  • Page 38 Update Software(receiver to receiver) Connect master and slave receivers with twisted RS-232C cable. Power on the master receiver and make it in standby mode input number key. Turn on slave receiver to begin update. Input the password “123” by remote control to update the software. After update, it will display “-End”...
  • Page 39 b) RS232 CABLE LAYOUT # CONNECT TO P.C c) Among wires from no.1 to 9 connect wire no.2 and 3 crossed to both sides, and then connect the GROUND(GND) of terminal on P.C to SVR, and then cut other wires. Upgrade by Satellite This function can upgrade the software of your receiver through data sent by a...
  • Page 40: Satcodx Auto Programming

    6.6 SatcoDX Auto Programming This function is using the tables of the SatcoDX websites to update your channel and satellite lists. You need a special application which is available on the CD-ROM of the Tele-Satellite magazine. Install this software on your PC first.
  • Page 41: Technical Specification

    7. Technical Specification VIDEO Decoding Bit rate Output Aspect ratio Active pixel Output connector AUDIO Decoding Mode Bit rate DEMODULATOR Demodulation Symbol rate Outer code Inner code Energy dispersion INPUT SIGNAL Frequency Input level Channel bandwidth Input socked RF MODULATOR Input Output Band...
  • Page 42 MISCELLANEOUS Supply voltage Power consumption Operation temperature Storage temperature Dimension (W x D x H) Weight Technical specification 100~240VAC 50/60Hz 30 watts max ° ° C to +40 ° ° C to +70...

Table of Contents