Related Manuals for Pakedge SK-24
Summary of Contents for Pakedge SK-24
- Page 1 QUICK START GUIDE SK-24 / SK-24F Fully Managed Gigabit Switch with 24 Front or Rear Facing Ports Version 1.0 pakedgedevice&software inc...
-
Page 2: Table Of Contents
Preparing to Install the Switch Installation Logging Into the Switch Changing the IP Address of the Switch Pakedge Zone & VLAN Setup Manually Configuring VLANs Console Into the Switch Resetting IP address through the console Factory defaulting through the console... -
Page 3: Switch Overview
The SK Series switches are fully managed gigabit switches, designed to address a wide range of networking needs. The SK Series switches are encased in AV like housings to appeal to customers demand for aesthetics. The following chart defines the features of the SK-24/SK-24F. Port Speeds 10/100/1000 mbps... -
Page 4: Preparing To Install The Switch
Installing the SK-24 is similar to installing any other Pakedge switch. If you have installed a man- aged switch before, the process will be very similar. The GUI for the SK-24 and SK-24F switches will be the same so the configuration steps discussed later in this quick start guide can be used on any of the switches. -
Page 5: Logging Into The Switch
A web page will appear asking you for a Username and Password. The default username is pakedge and the password is pakedges. Once you have logged into the switch you will have access to the GUI and will be able to... -
Page 6: Changing The Ip Address Of The Switch
In this section you can enter the switch IP address in the box next to “IP Address”. By default the switch IP is 192.168.1.205. You will also need to enter the “Subnet Mask” and “Gateway” settings for your network. By default on a Pakedge network subnet mask is 255.255.255.0 and the Gateway will be 192.168.1.99. -
Page 7: Pakedge Zone & Vlan Setup
Pakedge Zone & VLAN Setup New to the SK Series switches are the Pakedge Zones. Pakedge Zones provide a simple way to configure the switch to match the specialized VLAN settings of a Pakedge network. This new VLAN configuration page allows for very quick implmentation of VLAN settings across all... -
Page 8: Manually Configuring Vlans
Then click “Apply” to save that VLAN to the switch. VLAN ID’s 1 - 6 are color coded to match the Pakedge Zones these are used for. To configure ports as different VLANs, use the “Port Assignments” section. - Page 9 To set ports with the ability to only access a single VLAN, click the VLAN you want to use under “Access”. Then click on the ports above you wish to set with that VLAN. Once you have the ports you want selected, click Apply at the bottom of the page to save those settings. To set ports in Hybrid mode (one Default VLAN and multiple Tagged VLANs), first click the “+”...
-
Page 10: Console Into The Switch
Console Into the Switch The SX Series switches have a console port to serve as a back door entrance to the switch. This can be beneficial in case the switch is not functioning properly or if the incorrect IP address was configured. -
Page 11: Resetting Ip Address Through The Console
Resetting IP address through the console You can reset the IP address of the switch through the console. This can be helpful in case of miss- configuration. To do this you will first need to console into the switch as previously described and then take the following steps: Type show interface 1 and press enter to see the current IP address Type configure terminal and press enter... - Page 12 The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. pakedgedevice&software inc 3847 Breakwater Avenue Hayward,CA 94545 Main: 650-385-8700 Fax: 650.685.5520 www.pakedge.com sales@Pakedge.com © Pakedge Device & Software Inc. 2015 – All Rights Reserved...