Advertisement

Quick Links

• •
Quick-Start Manual
CMD 68-54/104 V2
English

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CMD 68-54 and is the answer not in the manual?

Questions and answers

Summary of Contents for PQ Plus CMD 68-54

  • Page 1 • • Quick-Start Manual CMD 68-54/104 V2 English...
  • Page 2: Table Of Contents

    Quick-Start Manual Inhaltsverzeichnis Installation ....................3 Direct connection ..................3 Current transformer /5 und /1A ..............3 Installation instruction ..................3 Inbetriebnahme ..................4 Menu Navigation ..................4 Commissioning / Check-up ................4 Tariff control ....................5 Current transformer ratio ................6 Date / Time ....................6 S0 pulse-output ....................7 M-Bus Interface ...................8 Modbus RTU RS485 Interface ..............8 TCP/IP interface ...................9...
  • Page 3: Installation

    PQ Plus – CMD 68-54/104 V2 Installation Direct connection Current (I 0.02 A / 0.15 A / 0.5 A / 5 A / 100 A Current transformer /5 und /1A Current /5A (I 0.005 A / 0.05 A / 0.25 A / 5 A / 5 A Current /1A (I 0.002 A / 0.01 A / 0.05 A / 1 A / 1 A...
  • Page 4: Inbetriebnahme

    Quick-Start Manual Inbetriebnahme Menu Navigation Go to next unit. Active energy, active power etc. More information on selected unit E.g. phase L1, L2, L3, total, min/ max values Service key, on the right side below the red terminal cover. SRVC Change &...
  • Page 5: Tariff Control

    PQ Plus – CMD 68-54/104 V2 Tariff control Tariff changeover takes place by 230V to corresponding terminal. Doppeltarif Tarif 0 = No voltage 1 = 230V...
  • Page 6: Current Transformer Ratio

    Quick-Start Manual Current transformer ratio Current transformer ratio can be adjusted from 5A/ 5A to 20‘000A/ 5A and 1A/ 1A to 4’000/ 1A Configuration of current transformer ratio Arrow right to Settings Arrow down to CT Ratio Arrow right to choose digit, Arrow down to change digit Save: Push Service key for 5 seconds, until LCD flashes Date / Time Configuration...
  • Page 7: S0 Pulse-Output

    PQ Plus – CMD 68-54/104 V2 S0 pulse-output The S0 pulse-output is designed according to EN62053-31 (DIN 83864). Default settings ex-factory S0 Output : Active Energy Import (Terminal 6 + 7) Indirect (CT) meter: 10 Impulse / kWh Direct meter:...
  • Page 8: M-Bus Interface

    Quick-Start Manual M-Bus Interface Default settings ex-factory Secondary address: Serial number Primary address: Baud rate: 2400 Configuration via M-Bus Primary and secondary address, baud rate and read-out data can be con- figured by the free EMU MB-Connect software or with the arrow keys. Configuration of primary-/ secondary address and Baud Arrow right to Settings Arrow down to primary-/secondary adress/ Baudrate...
  • Page 9: Tcp/Ip Interface

    PQ Plus – CMD 68-54/104 V2 TCP/IP interface Default settings ex-factory Network configuration by DHCP. Configuration of IP address Arrow right to Settings Arrow down to IP-Adress Arrow right to choose digit, Arrow down to change digit Save: Push service key for 5 seconds, until LCD flashes Error messages If an internal error appears, an error message is displayed.
  • Page 10: Technical Data

    Short-term 95%, Non-condensing Safety instruction The CMD 68-54/-104 should only be used for measuring electrical energy and can not be operated outside the specified technical data. When installing or replacing the meter, the conductors, to which the meter is connected, have to be dead (power/ voltage off).
  • Page 11: Maintenance

    PQ Plus GmbH. Disclaimer / Liability exclusion The choice of the CMD 68-54/-104 and determination of the suitability of the meter type for a particular purpose are solely the responsibility of the buyer.
  • Page 12 PQ Plus GmbH Hagenauer Straße 6 91094 Langensendelbach Phone: (+49) 9133-60640-0 Fax: (+49) 9133-60640-100 Mail: info@pq-plus.de Web: http://www.pq-plus.de Managing Director: Daniel Fierus-Beyer VAT identification number: DE 301 767 284 Further information and the current catalogue Release: 2022.03 can be found on our website:...

This manual is also suitable for:

Cmd 68-104

Table of Contents