Inalto IFLW7D40 User Manual page 9

e the transport bolts from the backside before using the product. • You must remove the transport bolts from the backside before using the product.
INSTALLATION
INSTALLATION
Remove transport bolts
Remove transport bolts
Warning!
Warning!
REMOVING TRANSPORT BOLTS
• You must remove the transport bolts from the backside before using the product.
Loosen the 4 transport Remove the bolts
WARNING! You must remove the transport bolts from the backside before using the product.
• You must remove the transport bolts from the backside before using the product.
bolts with a spanner. including the rubber parts
and keep them for future
use.
asher dryer Levelling the washer dryer
Warning!
Loosen the 4 transport
Loosen the 4 transport
Loosen the 4 transport
bolts with a spanner.
bolts with a spanner.
bolts with a spanner.
all four feet must be screwed tightly against the housing. • The lock nuts on all four feet must be screwed tightly against the housing.
LEVELING THE WASHER DRYER 1. Loosen the lock nut.
Levelling the washer dryer
WARNING! The lock nuts on all four feet must be screwed tightly against the housing.
Levelling the washer dryer
2. Turn the foot until it reaches the floor.
Warning!
1. Loosen the lock nut.
2. Turn the foot until it reaches the floor. 3. Adjust the legs and lock the nuts with a
• The lock nuts on all four feet must be screwed tightly against the housing.
Warning!
3. Adjust the legs and lock the nuts with a spanner. Make sure the machine is level and steady.
spanner. Make sure the machine is level and
• The lock nuts on all four feet must be screwed tightly against the housing.
steady.
ter supply hose Connect the water supply hose
Warning!
Connect the water supply hose
CONNECTING THE WATER SUPPLY HOSE
or water damage, follow the instructions in this chapter To prevent leakage or water damage, follow the instructions in this chapter
To prevent leakage or water damage, ensure you follow the instructions below; Warning!
• Do not kink, crush or modify water inlet hose.
or modify water inlet hose. • Do not kink, crush or modify water inlet hose.
To prevent leakage or water damage, follow the instructions in this chapter
• Connect the water supply hose to the water inlet valve and a water tap with cold water as indicated.
Connect the water supply hose
• Do not kink, crush or modify water inlet hose.
Connect the water supply hose
Warning!
INSTALLATION INSTALLATION
to the water inlet valve and a
To prevent leakage or water damage, follow the instructions in this chapter
water tap with cold water as
• Do not kink, crush or modify water inlet hose.
indicated.
Drain Hose Drain Hose
Note!
Note!
Warning! Warning!
NOTE! Connect manually, do not use tools. Check if the connections are tight.
• Connect manually, do not use tools. Check if the connections are tight.
• • Do not kink or protract the drain hose. Do not kink or protract the drain hose.
ly, do not use tools. Check if the connections are tight. • Connect manually, do not use tools. Check if the connections are tight.
DRAIN HOSE
• Position drain hose properly ,otherwise damage might result of water leakage. • Position drain hose properly ,otherwise damage might result of water leakage.
• Do not kink or protract the drain hose.
• Position drain hose properly, otherwise damage might result of water leakage.
There are two ways to place the end of drain hose: There are two ways to place the end of drain hose: Note!
1.Put it into the water trough. 1.Put it into the water trough.
There are two ways to place the end of drain hose
• Connect manually, do not use tools. Check if the connections are tight.
1. Put it into the water trough.
11
Water Water
trough trough
Remove the bolts Close the holes using the
including the rubber parts cover caps.
and keep them for future
use.
Remove the bolts
Remove the bolts
Remove the bolts
including the rubber parts
including the rubber parts
including the rubber parts
and keep them for future
(keep them in a safe place
and keep them for future
use.
for future use).
use.
1. Loosen the lock nut.
2. Turn the foot until it reaches the floor.
3. Adjust the legs and lock the nuts with a
spanner. Make sure the machine is level and
1. Loosen the lock nut.
steady.
2. Turn the foot until it reaches the floor.
3. Adjust the legs and lock the nuts with a
1. Loosen the lock nut.
spanner. Make sure the machine is level and
2. Turn the foot until it reaches the floor.
steady.
3. Adjust the legs and lock the nuts with a
spanner. Make sure the machine is level and
steady.
Connect the water supply hose
Connect the water supply hose
to the water inlet valve and a
to the water inlet valve and a
water tap with cold water as
water tap with cold water as
indicated.
indicated.
Connect the water supply hose
to the water inlet valve and a
water tap with cold water as
indicated.
11
2.Connect it to the branch drain pipe of 2.Connect it to the branch drain pipe of
the trough. the trough.
2. Connect it to the branch drain pipe of the trough.
Close the holes using the
Close the holes using the
Close the holes using the
cover caps.
cover caps.
11
11
9
Close the holes using the
cover caps.
cover caps.