MT584 User’s Manual V1.0 Table of Content CHAPTER 1 INTRODUCTION ............................. 7 .................................... 7 PECIFICATIONS ..................................9 EEPER NDICATION LED I ..................................10 NDICATION CHAPTER 2 GENERAL SETTINGS..........................11 ............................... 11 ARCODE ONFIGURABILITY ..................................11 ACTORY EFAULT ..................................11 HECK ERSION .................................
Page 3
MT584 User’s Manual V1.0 Check Bluetooth Firmware Version ........................... 29 Check Device MAC Address ............................... 30 Check Host MAC Address ..............................30 Check Battery Life ................................30 ScanLink ....................................31 ................................... 32 EMORY Delete Last Record ................................32 Clear All Record ..................................32 Data Format ...................................
MT584 User’s Manual V1.0 Chapter 1 Introduction This user’s manual is dedicated to MT584, a wearable 2D wireless ring scanner that enables hands-free scanning for mobile operators who work with smartphones or other mobile devices of iOS and Android platform. With built-in Bluetooth 5.0 technology and disinfectant-ready housing, MT584 provides 20-meter wireless data transmission and microbe-free scanning experience.
Page 8
MT584 User’s Manual V1.0 (Environment: 800 lux) 13 Mil UPC/EAN : 55 ~ 285mm 15 Mil QR Code : 25 ~ 230mm 6.67 Mil PDF417 : 45 ~ 135mm 10 Mil Data Matrix: 40 ~ 135mm Physical Characteristics Dimension W27.6 x L46.2 x H26.8 mm...
MT584 User’s Manual V1.0 LED Indication Status Power off / Standby / Connected Flashing blue Disconnected / Discoverable One green flash Good read Flashing red Low power Solid red Charging...
MT584 User’s Manual V1.0 Chapter 2 General Settings Barcode Configurability Scanning below configuration barcodes will allow/prohibit user to change settings by scanning configuration barcodes in this manual. Enable Barcode Configurability* Disable Barcode Configurability Factory Default Scanning below configuration barcode will reset all parameters to factory default settings (the ones...
MT584 User’s Manual V1.0 Button Preference Scan one of below barcodes to determine which touch-sensing button to enable according to your habit: Right Button Only Left Button Only (For Left-handed User) (For Right-handed User) Both Button* Good Read Indicator Beep Tone Beep Low (2.0KHz)
MT584 User’s Manual V1.0 Beep Mode Normal* Warning Beep Only Mute Data Format UTF-8 to Unicode Conversion Off* Note: To output double-byte character (i.g. Chinese) using UTF-8 to Unicode Conversion, please make sure that the application accepting barcode data supports Unicode display (i.g. Word, TeraTerm).
MT584 User’s Manual V1.0 HT/CR/ESC Converts to TAB/ENTER/ESCAPE Off* Note: 1. By default, HT [$I], CR [$M] and ESC [%A] is transmitted as <0x09>, <0x0D> and <0x1B> respectively. 2. When enabled, HT [$I], CR [$M] and ESC [%A] is transmitted as <TAB>, <ENTER> and <ESCAPE>...
MT584 User’s Manual V1.0 Control Code Output Method Ctrl Mode* Alt Mode Disable Output Note: Control code (0x01 ~ 0x1A) can be sent by two methods: (1) Ctrl Mode: A barcode of “A<HT>F” (0x41/0x09/0x46) is scanned, the output sequence is: a.
MT584 User’s Manual V1.0 Numeric Key Numeric Key Alphanumeric Key* Note: 1. By default, the alphanumeric key is used for trasmitting digits. Scan NUMERIC KEY if you want to use the keys on the numeric keypad. 2. If you select NUMERIC KEY, the Num Lock status of the physical keyboard should be ON.
MT584 User’s Manual V1.0 Keyboard Layout English (US)* English (UK) Danish Spanish Hungarian (QWERTZ) Hungarian (QWERTY) Canadian French Dutch Italian French German Swiss German...
Page 19
MT584 User’s Manual V1.0 Swiss French Swedish Czech (QWERTZ) Czech (QWERTY) Norwegian Belgian Portuguese Slovak Brazilian (QWERTY) Canadian (Traditional) Japanese Alt Code...
MT584 User’s Manual V1.0 Intercharacter Delay The configurable range is from 0 to 255ms. The larger the number, the longer the delay. Set Intercharacter Delay (Default = 4ms) Example: Set Intercharacter Delay to 8ms Step1: Scan Set Intercharacter Delay Step2: Scan “0” “0” “8” in Appendix - Numbers...
MT584 User’s Manual V1.0 BCC (Binary Check Character) Off* Note: Once enabled, a checksum will be added to the end of each data to conduct Xor calculation. For Bluetooth SPP & USB VCP, the BCC is 1 byte. For Bluetooth HID & USB HID, the BCC are 2 bytes.
MT584 User’s Manual V1.0 Note: 1. When enabled, the <GS> character in all barcodes will be replaced by the one defined by the user. 2. To define replacement character, please refer to below: Example: Set Replacement Character as “X" Step1: Scan “Define Replacement Character”...
MT584 User’s Manual V1.0 Chapter 3 Interface BT HID Getting Connected 1. Press the function button on the top to power up the scanner. 2. Scan “Disconnect”, the scanner will emit two beeps. Disconnect 3. Scan “BT HID”, the scanner will emit two beeps.
MT584 User’s Manual V1.0 Pincode Setup If Bluetooth application prompts you to enter a pincode, please follow the steps: 1. Scan “Pincode Start” Pincode Start 2. Scan numeric barcodes below according to the pincode generated by the Bluetooth application. 3. Scan “Enter”...
MT584 User’s Manual V1.0 4. Scan “Pincode Stop” Pincode Stop BT SPP Getting Connected 1. Press the function button on the top to power up the scanner. 2. Scan “Disconnect”, the scanner will emit two beeps. Disconnect 3. Scan “BT SPP Master”(recommeded) or “BT SPP Slave”, the scanner will emit two beeps. If host can’t auto-reconnect, use BT SPP Master.
MT584 User’s Manual V1.0 Set SPP Pincode By default, the pincode under BT SPP profile for the scanner is “1234”. It is configurable up to 8 numbers. Set SPP Pincode Example: Set SPP Pincode to 0000. Step1: Scan “Set SPP Pincode”...
MT584 User’s Manual V1.0 General Bluetooth Settings Power Off Timeout The power off timeout is 3 minutes & 0 second by default. They are configurable from a minimum of 10 seconds (00:10) to a maximum of 60 minutes and 59 seconds (60:59)
MT584 User’s Manual V1.0 Set Bluetooth Device ID Bluetooth device name is configurable up to 16 alphanumeric characters: Set Bluetooth Device ID Example: Set XYZ123 as Bluetooth Device ID Step 1: Scan “Set Bluetooth Device ID” Step 2: Scan “X” “Y” “Z” “1” “2” “3” in Appendix - Upper Case Alphabets & Numbers Step 3: Scan “Set Bluetooth Device ID”...
MT584 User’s Manual V1.0 Check Device MAC Address To check scanner’s MAC address, please connect to a host device via BT HID or BT SPP and scan below configuration barcode. Check Device MAC Address Check Host MAC Address To check scanner’s MAC address, please connect to a host device and scan below configuration barcode.
MT584 User’s Manual V1.0 ScanLink ScanLink is a connection method that turns the scanner into a master device, which initiates the Bluetooth connection with the target host device (now a slave device). This, as a result, saves user the trouble of going through numerous setup procedures on the host device to establish connection.
MT584 User’s Manual V1.0 Memory Mode Memory Mode After scanning the above barcode, the scanner will be able to collect barcode data off-line. The barcode data will be stored in the format of: <Date>, <Time>, <Barcode Data> <CR> To retrieve stored data, please connect the scanner to the host with USB cable, access removable storage device “MiniScan”...
MT584 User’s Manual V1.0 Data Format The default Data Format in memory mode is <Date>, <Time>, <Barcode Data>. Data Format Below are configurable items and their setup codes: Code Item Date Time Barcode Data Example: Set Data Format as <Barcode Data>, <Date>, <Time>...
MT584 User’s Manual V1.0 Date Format The default Date Format is DD/MM/YYYY (Code = 09) Date Format Below are available Date Format and their setup codes: Code Date Format Code Date Format DD-MM-YYYY DD/MM/YYYY MM-DD-YYYY MM/DD/YYYY DD-MM-YY DD/MM/YY MM-DD-YY MM/DD/YY...
MT584 User’s Manual V1.0 Date & Time Setup Set Date Set Time Example: Set date as 2022-07-27, set time as 08:10:30 am (HH:MM:SS) Step1: Scan “Set Date” Step2: Scan “2” “2” “0” “7” “2” “7” in Appendix - Numbers Step3: Scan “Set Date”...
MT584 User’s Manual V1.0 Chapter 4 Reading Mode Trigger Mode In Trigger Mode the LED will stay on once trigger is pressed and held, and will turn off automatically once a barcode is read or LED Auto-Off timeout expires. Trigger Mode*...
MT584 User’s Manual V1.0 Auto-sensing Mode In Auto-sensing Mode the LED will turn on when image change is detected within scanner’s field of view, and will turn off when: (1) a barcode is read (2) LED Auto-Off timeout expires (3) trigger is...
MT584 User’s Manual V1.0 Advanced Reading Mode Settings LED Auto-Off Timeout LED Auto-Off Timeout (applicable for all reading modes) is the maximum scanning duration. When LED Auto-Off Timeout expires, the scanning operation stops automatically. The configurable range is from 0.1 to 25.5 sec.
MT584 User’s Manual V1.0 Chapter 5 Data Format By default data format is as follows: <Preamble> <Code ID> <Barcode Length> <Barcode Data> <Postamble> <Terminator> Code ID When Factory ID is enabled, a Factory ID (see Appendix – Factory ID Table) will be added to the beginning of each barcode data.
Page 41
MT584 User’s Manual V1.0 Set ID – Code32 Set ID – Codabar Set ID – Interleaved 2 of 5 Set ID – Standard 2 of 5 Set ID – Matrix 2 of 5 Set ID – Industrial 2 of 5 Set ID –...
Page 42
MT584 User’s Manual V1.0 Set ID – Code93 Set ID – Code128/GS1-128 Set ID – GS1 Databar Set ID – GS1 Databar Limited Set ID – GS1 Databar Expanded Set ID – QR Code Set ID – Micro QR Code Set ID –...
MT584 User’s Manual V1.0 Example: Set Code39 Set ID as XY Step1: Scan “Set ID – Code39” Step2: Scan “X” “Y” in Appendix - Upper Case Alphabets Step3: Scan “Set ID – Code39” Data Length Send Data Length Off* Send Data Length On Preamble Preamble can be up to 16 bytes of data.
MT584 User’s Manual V1.0 Postamble Postamble can be up to 16 bytes of data. Set Postamble Example: Set Postamble as XYZ123 Step 1: Scan “Set Postamble” Step 2: Scan “X” “Y” “Z” “1” “2” “3” in Appendix - Upper Case Alphabets & Numbers Step 3: Scan “Set Postamble”...
Page 45
MT584 User’s Manual V1.0 <TAB> <Space> <ESC> Note: 1. Default Terminator for BT HID or USB HID interface = <CR> (or Enter) 2. Default Terminator for BT SPP or USB VCP interface = <CR><LF> 3. <CR><LF> or <LF> is treated as Enter for BT HID or USB HID interface.
MT584 User’s Manual V1.0 Chapter 6 Symbologies General Settings Enable All Symbologies Disable All Symbologies Enable All 1D Symbologies Disable All 1D Symbologies Enable All 2D Symbologies Disable All 2D Symbologies Note: When all symbologies are disabled, configuration barcodes are still readable.
MT584 User’s Manual V1.0 Note: When Addenda Required is enabled, the scanner will only read an UPC-A barcode that has 2-digit or 5-digit addenda/supplement. UPC-E Enable/Disable UPC-E Enable UPC-E* Disable UPC-E Check Digit Send Check Digit* Not Send Check Digit...
MT584 User’s Manual V1.0 Enable Addenda Required Disable Addenda Required* Note: When Addenda Required is enabled, the scanner will only read an UPC-E barcode that has 2-digit or 5-digit addenda/supplement. EAN-8 Enable/Disable EAN-8 Enable EAN-8* Disable EAN-8 Check Digit Not Send Check Digit...
MT584 User’s Manual V1.0 Enable 2-digit Supplement Disable 2-digit Supplement* Enable Addenda Required Disable Addenda Required* Note: When Addenda Required is enabled, the scanner will only read an EAN-8 barcode that has 2-digit or 5-digit addenda/supplement. EAN-13 Enable/Disable EAN-13 Enable EAN-13*...
MT584 User’s Manual V1.0 Add On Supplement Enable 5-digit Supplement Disable 5-digit Supplement* Enable 2-digit Supplement Disable 2-digit Supplement* Enable Addenda Required Disable Addenda Required* Note: When Addenda Required is enabled, the scanner will only read an EAN-13 barcode that has 2-digit...
MT584 User’s Manual V1.0 Full ASCII Code39 Enable Full ASCII Code39* Disable Full ASCII Code39 Code39 Min/Max Length Set Min Length Set Max Length (Default = 01) (Default = 99) Example: Set Min Length as 8, Max Length as 12 for Code39 Step1: Scan “Set Min Length”...
MT584 User’s Manual V1.0 Codabar Min/Max Length Set Min Length Set Max Length (Default = 01) (Default = 99) Example: Set Min Length as 8, Max Length as 12 for Codabar Step1: Scan “Set Min Length” Step2: Scan “0” “8” in Appendix – Numbers Step3: Scan “Set Min Length”...
MT584 User’s Manual V1.0 Interleaved 2 of 5 Min/Max Length Set Min Length Set Max Length (Default = 04) (Default = 32) Example: Set Min Length as 8, Max Length as 12 for Interleaved 2 of 5 Step1: Scan “Set Min Length”...
MT584 User’s Manual V1.0 Standard 2 of 5 (IATA) Enable/Disable Standard 2 of 5 Enable Standard 2 of 5 Disable Standard 2 of 5* Verification Disable CDV* CDV & Send CD CDV & Not Send CD...
MT584 User’s Manual V1.0 Standard 2 of 5 Min/Max Length Set Min Length Set Max Length (Default = 04) (Default = 32) Example: Set Min Length as 8, Max Length as 12 for Standard 2 of 5 Step1: Scan “Set Min Length”...
MT584 User’s Manual V1.0 Matrix 2 of 5 Min/Max Length Set Min Length Set Max Length (Default = 04) (Default = 32) Example: Set Min Length as 8, Max Length as 12 for Matrix 2 of 5 Step1: Scan “Set Min Length”...
MT584 User’s Manual V1.0 Industrial 2 of 5 Min/Max Length Set Min Length Set Max Length (Default = 04) (Default = 32) Example: Set Min Length as 8, Max Length as 12 for Industrial 2 of 5 Step1: Scan “Set Min Length”...
MT584 User’s Manual V1.0 Verification Single Digit* Double Digits Check Digit Send Check Digit Not Send Check Digit* Code 11 Min/Max Length Set Min Length Set Max Length (Default = 04) (Default = 32) Example: Set Min Length as 8, Max Length as 12 for Code11 Step1: Scan “Set Min Length”...
MT584 User’s Manual V1.0 China Postal Code Enable/Disable China Postal Code Enable China Postal Code Disable China Postal Code* Verification Disable CDV* CDV & Send CD CDV & Not Send CD...
MT584 User’s Manual V1.0 China Postal Code Min/Max Length Set Min Length Set Max Length (Default = 04) (Default = 32) Example: Set Min Length as 8, Max Length as 12 for China Postal Code Step1: Scan “Set Min Length”...
MT584 User’s Manual V1.0 MSI Plessey Min/Max Length Set Min Length Set Max Length (Default = 04) (Default = 32) Example: Set Min Length as 8, Max Length as 12 for MSI Plessey Step1: Scan “Set Min Length” Step2: Scan “0” “8” in Appendix – Numbers Step3: Scan “Set Min Length”...
MT584 User’s Manual V1.0 UK Plessey Enable/Disable UK Plessey Enable UK Plessey Disable UK Plessey* Check Digit Send Check Digit Not Send Check Digit*...
MT584 User’s Manual V1.0 Code 93 Enable/Disable Code 93 Enable Code 93* Disable Code 93 Code 93 Min/Max Length Set Min Length Set Max Length (Default = 01) (Default = 99) Example: Set Min Length as 8, Max Length as 12 for Code93 Step1: Scan “Set Min Length”...
MT584 User’s Manual V1.0 Code 128/GS1-128 Enable/Disable Code 128/GS1-128 Enable Code 128/GS1-128* Disable Code 128/GS1-128 Code 128/GS1-128 Min/Max Length Set Min Length Set Max Length (Default = 01) (Default = 99) Example: Set Min Length as 8, Max Length as 12 for Code128/GS1-128 Step1: Scan “Set Min Length”...
MT584 User’s Manual V1.0 GS1 DataBar Expanded Min/Max Length Set Min Length Set Max Length (Default = 04) (Default = 32) Example: Set Min Length as 8, Max Length as 12 for GS1 DataBar Expaneded Step1: Scan “Set Min Length”...
MT584 User’s Manual V1.0 QR Code Enable/Disable QR Code Enable QR Code* Disable QR Code Micro QR Code Enable/Disable Micro QR Code Enable Micro QR Code* Disable Micro QR Code Data Matrix Enable/Disable Data Matrix Enable Data Matrix* Disable Data Matrix...
MT584 User’s Manual V1.0 Home Enter (Numeric Key) Appendix – Navigation Keys Cursor Left Cursor Right Cursor Up Cursor Down Page Up Page Down Back Tab...
MT584 User’s Manual V1.0 Enter Appendix – Modifier Keys Alt (Left) make *1 Alt (Left) break Alt (Right) make Alt (Right) break Shift (Left) make *2 Shift (Left) break...
Page 91
MT584 User’s Manual V1.0 Shift (Right) make Shift (Right) break Win (Left) make Win (Left) break Win (Right) make Win (Right) break Ctrl (Left) make *3 Ctrl (Left) break Ctrl (Right) make Ctrl (Right) break Note: *1: When “Alt (Left) make” is programmed, please scan “Alt (Left) break” to resume barcode setting.
MT584 User’s Manual V1.0 Appendix - Abort If there is an error reading data barcode during multi-step configuration, you may cancel configuration by scanning below configuration barcode. Abort...
MT584 User’s Manual V1.0 Appendix - Default Table Function Default Remark General Settings Barcode Configurability Button Preference Both Button Beep Tone High (4.0KHz) Beep Mode Normal Data Format UTF-8 to Unicode Conversion HT/CR/ESC Converts to TAB/ENTER/ESCAPE Function Code Conversion Control Code Output Method...
Page 94
MT584 User’s Manual V1.0 Continuous Mode Auto-sensing Mode LED Auto-Off Timeout 5 sec Scan Interval 1 sec Identical Read Interval 1 sec Trigger Control Data Format Code ID Disable Code ID Set ID Data Length Preamble Postamble CR (BT HID / USB HID)
Page 95
MT584 User’s Manual V1.0 Addenda Required Code 39 Enable/Disable Verification Disable CDV Start/Stop Not Send Full ASCII Code39 Min Length Max Length Code 32 Enable/Disable Leading/Tailing Send Leading & Tailing Codabar Enable/Disable Verification Disable CDV Start/Stop Not Send Min Length...
Page 96
MT584 User’s Manual V1.0 Check Digit Not Send Min Length Max Length China Postal Code Enable/Disable Verification Disable CDV Min Length Max Length MSI Plessey Enable/Disable Verification Send Check Digit Single Check Digit MOD10 Min Length Max Length UK Plessey...