Page 1
NOTE: Please read all instructions carefully before using this product Table of Contents ® MARCY BENCH & Safety Notice WEIGHT SET Hardware Identifier MWB-36780B Assembly Instruction Parts List Warranty Ordering Parts Model MWB-36780B Retain This Manual for Reference 170305 OWNER'S...
ORDERING PARTS..................… BEFORE YOU BEGIN Thank you for selecting the MARCY MWB-36780B Bench & Weight Set. For your safety and benefit, read this manual carefully before using the machine. As the official representative for Marcy, we are committed to providing complete customer satisfaction.
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. PURE-TEC LTD ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS. www.puretecfitness.com Marcy Fitness...
HARDWARE IDENTIFIER NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. www.puretecfitness.com Marcy Fitness...
Washers (#39), and two M10 Aircraft Nuts (#43) on each end of the Cross Brace. E.) Place the Backrest Adjustment Bar (#32) onto the selected slots on the Upright Beams to obtain desired incline for the Backrest. DIAGRAM 1 www.puretecfitness.com Marcy Fitness...
Page 7
D.) Attach the other end of Main Seat Stabilizer (#9) to the Front Leg (#5). Secure it with one M8 x 5/8” Allen Bolt (#35) and Ø 5/8” Washer (#40). E.) Securely tighten all Nuts and Bolts previously installed. DIAGRAM 2 www.puretecfitness.com Marcy Fitness...
Page 8
B.) Insert two Foam Tubes (#11) halfway through the holes on the Leg Developer. Push four Foam Rolls (#28) onto the Tubes from both sides. C.) Attach a Spring Clip (#19) to the weight post on Leg Developer. DIAGRAM 3 www.puretecfitness.com Marcy Fitness...
Page 9
Hex Bolts (#46) and Ø ½” Washers (#41). C.) Place the Seat Pad (#30) onto the Main Seat Support. Secure it with four M6 x 1 3/8” Hex Bolts (#38) and Ø ½” Washers (#41). DIAGRAM 4 www.puretecfitness.com Marcy Fitness...
Page 10
B.) Insert the Arm Curl Stand into the top opening on the Front Leg. Secure it with a M10 x 2 5/8” Lock Knob (#45). C.) When using Leg Developer, remove the Arm Curl Stand from the Front Leg. DIAGRAM 5 www.puretecfitness.com Marcy Fitness...
Page 11
Secure the Handle with one M10 x 5/8” Allen Bolt (#47) and one Ø ¾” Large Washer (#48). Attach a Spring Clip (#19) to the weight post on the Butterfly. C.) Repeat Procedure A and B to install the other Butterfly to Right Upright Beam (#1). DIAGRAM 6 www.puretecfitness.com Marcy Fitness...
Page 12
If there are weight plates loaded/unloaded on the bar while on the bench, the plates should be loaded/unloaded in equal amounts; preventing the bar from being unevenly weighted, and causing the bar to tip. DIAGRAM 7 www.puretecfitness.com Marcy Fitness...
Monday to Friday, 8am until 5 pm GMT. Pure-Tec Limited www.puretecfitness.com Tel: +44 (0) 1482 212098 Email: service@puretecfitness.com Monday - Friday 0800 – 1700 GMT When ordering replacement parts, always give the following information. Model Description of Parts Part Number Date of Purchase www.puretecfitness.com Marcy Fitness...
Need help?
Do you have a question about the MWB-36780B and is the answer not in the manual?
Questions and answers