General Maintenance - Warming Trends CFB60 NG Owner's Manual And Instruction Manual

ever handling gas log.
Once your approved media has been installed, place
your FireStorm Steel Gas Log over the burner so that
the burner is centered underneath it. Your steel log has
a "lighting opening" at each end to aid in lighting the
burner. (See Figure 1 below). Orient the steel log so that
one end of the log is near the key valve. Press down upon
the log to seat the log in the media to create a level and
stable foundation. Adjust media as necessary.
Adjust your media so that the tip of the jet nearest the end
of the log to be used for lighting is exposed. Use this jet
for lighting the burner pursuant to Steps 6 and 7 below.
Lighting Opening
LIGHTING AND TURNING OFF YOUR MATCH LIT
FIRESTORM STEEL GAS LOG SYSTEM
These instructions supplement the Lighting Instructions
within your Owner's Manual related to Turning On Your
Match Lit System. Light your FireStorm Steel Gas Log
using a "lighting opening" to access your burner as de-
scribed below.
TURNING ON YOUR MATCH LIT SYSTEM
1. STOP! Read all the safety information.
2. Any cover must be removed prior to operation of
burner or appliance and must remain off during
operation.
area immediately. After leaving the area, call your
which could cause property damage, personal
injury or death.
3.
pane supply to the appliance is open. Do not open
your key valve or gas control at this time.
4.
move any accumulated leaves or other combustible
debris.
5. Locate key valve or gas control valve controlling gas
supply to your appliance.
6. Locate the jet tip nearest the "lighting opening"
described above that can be easily accessed while
operating key valve or gas control without reaching
across other jets or the burner. Reorient burner if
necessary to allow such access.
7. Place a long reach lighter through the "lighting
opening" of the gas log slightly above or on the tip of
the jet located in Step 6 above. (See Figure 1). Do not
use a match or cigarette lighter.
8.
tip as described in Step 7 above, slowly turn the key
valve or gas control knob slightly to the left to allow
22
-
-
-
www.Warming-Trends.com | 303 346 2224 | orders@warming-trends.com
selected jet. While attempting to light jet, do not sub-
before jet is lit can cause pooling of gas and result in
Failure to follow these instructions
property damage, personal injury or death.
9. Once the selected jet (or other jets) is lit, continue to
keep any body parts from above the pit or burner and
slowly turn the key valve or gas control knob further to
other jets of the burner should ignite.
10.
the key valve or gas control to the off position and call
your local technician or gas supplier for service prior
to re-attempting to operate your appliance.
11. Once lit, use the key valve or gas control to adjust the
TURNING OFF YOUR MATCH LIT BURNER
1. Use key to turn valve to OFF position by turning the
valve to the right.
2.
3. If using LP bottle/tank, turn bottle/tank to CLOSED
position.
4.
with waterproof/weatherproof cover.
APPEARANCE
Your steel log should patina over time by forming a layer
of rust or oxidation. The coloring may change and the log
will look more natural. Each log develops a unique patina
pattern based upon use and weather conditions. Heat will
also create distinctive color changes to your log's surface.
CLEANING STEEL LOG
Soot may build up along the openings in the log or on its
surface in general. Annual cleaning is recommended. How-
clean openings immediately. Prior to any cleaning or han-
dling, wait for log to cool completely and then remove
the log from the system. Soot is then easily removed by
spraying the log with water or by lightly brushing with a
plastic brush. Do not allow water or soot to fall into burner
system.

GENERAL MAINTENANCE

WARNING:
Fire feature should be inspected by user
prior to each use and inspected at least
service professional.
Any guard or protective device removed for servicing
must be replaced prior to operating the appliance.
nician. Appliances should be inspected prior to each use
appliance service professional.
Ensure gas and power (if applicable) are shut off and
Keep any debris out of appliance - clean as needed. If
debris is found, remove before lighting system.
-