Panasonic WV-CP290 Operating Instructions Manual page 10

A Flange-back adjustment ring A Flange-back adjustment ring
This ring adjusts the back-focal distance This ring adjusts the back-focal distance
or picture focus. or picture focus.
Important: Important:
• When an object is out of focus • When an object is out of focus
because it is too close to the camera, because it is too close to the camera,
focus on a darker object with the focus on a darker object with the
aperture open. aperture open.
B ALC lens connector B ALC lens connector
Supplies power and control signals to an Supplies power and control signals to an
auto iris lens (option). auto iris lens (option).
C Lens (option) C Lens (option)
Important: Important:
• The lens mount should be a CS mount • The lens mount should be a CS mount
(1"-32UN). (1"-32UN).
D Flange-back lock screw [LOCK] D Flange-back lock screw [LOCK]
Loosen this screw with a screwdriver to Loosen this screw with a screwdriver to
adjust the flange-back adjustment ring. adjust the flange-back adjustment ring.
When completing the adjustment, tighten When completing the adjustment, tighten
this screw. this screw.
Recommended tightening torque: Recommended tightening torque:
0.05 N·m {0.04 lbf·ft} 0.05 N·m {0.04 lbf·ft}
Important: Important:
• When the screw is tightened stronger • When the screw is tightened stronger
than the recommended tightening than the recommended tightening
torque, it may strip the thread or torque, it may strip the thread or
cause focus misalignment. cause focus misalignment.
E Tripod mount base E Tripod mount base
This socket is used to mount the camera This socket is used to mount the camera
mount bracket (option). The tripod socket mount bracket (option). The tripod socket
can be mounted on either top or bottom can be mounted on either top or bottom
of the camera head.(Tripod socket hole: of the camera head.(Tripod socket hole:
1/4-20 UNC for tripod) 1/4-20 UNC for tripod)
F Power connector (only for WV-CP290) F Power connector (only for WV-CP290)
The included power cord is connected to The included power cord is connected to
this power connector. this power connector.
G AC/DC G AC/DC power power
WV-CP294) WV-CP294)
The power supply of 24 V AC or 12 V DC The power supply of 24 V AC or 12 V DC
is connected to this terminal. is connected to this terminal.
H Video output connector [VIDEO OUT] H Video output connector [VIDEO OUT]
Composite video signals are transmitted. Composite video signals are transmitted.
If this unit is connected to the multiplex If this unit is connected to the multiplex
unit, the multiplexed VD2 that is prioritized unit, the multiplexed VD2 that is prioritized
over INT/LL is automatically selected. over INT/LL is automatically selected.
10 10
terminal terminal (only (only for for
I Dip switch I Dip switch
Selects ON/OFF for white balance mode, Selects ON/OFF for white balance mode,
backlight compensation, Adaptive Black backlight compensation, Adaptive Black
Stretch, day/night mode, and INT/LL for Stretch, day/night mode, and INT/LL for
synchronization mode. synchronization mode.
B. S. B. S.
D/ N D/ N BLC BLC
ON ON
ON ON ON ON
OF F OF F OF F OF F
OFF OFF
• Day/night mode selector [D/N] • Day/night mode selector [D/N]
ON: Switches from color to black-and- ON: Switches from color to black-and-
white images when the ambient white images when the ambient
brightness brightness (illuminance) (illuminance)
camera is approx. 0.8 lx or less. camera is approx. 0.8 lx or less.
OFF: Color picture is displayed normally. OFF: Color picture is displayed normally.
Default setting: ON Default setting: ON
Note: Note:
• To obtain color images, a sufficient • To obtain color images, a sufficient
level of illuminance(approx.30 lx or level of illuminance(approx.30 lx or
more) is required. more) is required.
• The switching illuminance level varies • The switching illuminance level varies
with subjects, light sources, and with subjects, light sources, and
lenses. lenses.
• The switching illuminances described • The switching illuminances described
above are reference values. The above are reference values. The
switching switching illuminance illuminance
decided decided based based
installation environment. installation environment.
• Adaptive Black Stretch Selector [B.S.] • Adaptive Black Stretch Selector [B.S.]
ON: The dark area of the object is ON: The dark area of the object is
automatically corrected to lighten it. automatically corrected to lighten it.
OFF: Does not compensate. OFF: Does not compensate.
Default setting: ON Default setting: ON
Important: Important:
• In the case of "ON" setting, noise may • In the case of "ON" setting, noise may
be increased in the dark area of the be increased in the dark area of the
object. object.
• In addition, darkness and brightness • In addition, darkness and brightness
may be emphasised in the vicinity of may be emphasised in the vicinity of
the boundary between the dark and the boundary between the dark and
bright areas. bright areas.
AT W AT W
INT INT
LL LL
AWC AWC
of of the the
shall shall be be
on on the the actual actual