Related Manuals for TUYA TYZS11
Summary of Contents for TUYA TYZS11
- Page 1 TYZS11 Module Datasheet Hardware Product Development > Network Modules > Zigbee Module > TYZS Series Module Version: 20210315 Online Version...
-
Page 2: Table Of Contents
Contents Contents 1 Overview 1.1 Features ....... . . 1.2 Major application fields . - Page 3 Contents TYZS11 is a low power-consuming embedded Zigbee module developed by Hangzhou Tuya Information Technology Co., Ltd. It consists of a highly integrated wireless radio processor chip (EFR32MG13P732) and several peripherals, with a built-in 802.15.4 PHY/MAC Zigbee network protocol stack and robust library functions.
-
Page 4: Overview
TYZS11 is embedded with a low power-consuming 32-bit ARM Cortex-M4 core, 512 KB flash, 64 KB RAM data memory, and robust peripheral resources. TYZS11 runs on the FreeRTOS platform that integrates all Zigbee MAC library func- tions. You can develop built-in Zigbee products as required. -
Page 5: Major Application Fields
– Built-in DC-DC circuit, maximizing the power-supply efficiency – Maximum output power: +19 dBm; dynamic difference of output power: > 35 dB – Power consumption when TYZS11 is working: 63 uA/MHz; current when TYZS11 is in the sleep state: 1.4 uA – Proactive network configuration for terminals –... -
Page 6: Module Interfaces
TYZS11 provides three rows of pins with a distance of 1.0 mm between every two pins. TYZS11 dimension: 15.3 mm (W) x 22 mm (L) x 2 mm (H). Figure 2 shows the overall pin layout of TYZS11. Figure 2 Front view of TYZS11 2.2 Pin definition... - Page 7 GPIO in normal programs. ADC port 1, corresponding to PB11 pin of the IC. ADC is a 12-bit precision SAR analog-to-digital converter. 8 and 18 3.3 V Power-supply pins of TYZS11 (typical power-supply voltage: 3.3 V) 5 / 24...
- Page 8 2 MODULE INTERFACES Symbol I/O Type Functions Corresponds to PF2 pin of the IC and functions as a GPIO. It can be used as an output pin when J-Link is used. Corresponds to PF6 pin of the IC and functions as a GPIO.
- Page 9 GPIO. nRST Hardware reset pin, and the chip is reset when the level is low. TYZS11 has a power-on reset function, and this pin is not necessary for the actual situation. GPIO2 Corresponds to PA5 pin of the IC and functions as a GPIO.
-
Page 10: Test Pin Definition
ADC input interface, the input voltage range must be 0–AVDD, which can be configured using the software. 2.3 Test pin definition Table 2 describes the test pins. Table 2 TYZS11 test pins Symbol I/O Type Functions Used for the module production test. -
Page 11: Electrical Characteristics
3 ELECTRICAL CHARACTERISTICS 3 Electrical Characteristics 3.1 Absolute Electrical Characteristics Table 3Absolute electrical characteristics Minimum Maximum Parameter Description Value Value Unit Storage °C temperature Power-supply -0.3 voltage Static TAMB -25°C electricity voltage (human model) Static TAMB -25°C electricity voltage (machine model) 3.2 Electrical Conditions Table 4 Normal electrical conditions... -
Page 12: Zigbee Tx Power Consumption
3 ELECTRICAL CHARACTERISTICS Minimum Typical Maximum Parameter Description Value Value Value Unit -0.3 VCC x 0.25 low-level input VCC x 0.75 high-level input VCC x 0.1 low-level output VCC x 0.8 high-level output Imax I/O drive current 3.3 Zigbee TX Power Consumption Table 5 TX power consumption during constant emission Typical Symbol... -
Page 13: Zigbee Rx Power Consumption
Rate Typical Value Unit 250 kbit/s Note: When the UART is in the active state, the received current is 14 mA. 3.5 Power Consumption in Operating Mode Table 7 TYZS11 working current Working Working Status (Ta = Average Maximum Mode 25°C) -
Page 14: Rf Features
4 RF FEATURES 4 RF Features 4.1 Basic RF Features Table 8 Basic RF features Parameter Description Frequency band 2.400 GHz to 2.484 GHz Physical-layer standard IEEE 802.15.4 Data transmitting rate 250 kbit/s Antenna type External copper column spring antenna and onboard PCB antenna Line-of-sight transmission distance >... -
Page 15: Zigbee Rx Sensitivity
4 RF FEATURES Minimum Typical Maximum Parameter Value Value Value Unit Output spectrum adjacent- channel rejection ratio Note: The maximum output power can reach +19 dBm. The power output can be adjusted under normal use. The high-power output can be used for overlay trans- mission in extremely complex conditions, such as modules embedded in a wall. -
Page 16: Antenna Information
5 ANTENNA INFORMATION 5 Antenna Information 5.1 Antenna Types By default, the onboard PCB antenna is used. It can be connected to an external cop- per spring antenna using a connector, which is used for wireless extended coverage in complex installation conditions. 5.2 Antenna Interference Reduction When you use a copper column antenna on a Zigbee module, make sure that the antenna on the module is at least 15 mm away from other metal parts to ensure... -
Page 17: Packaging Information And Production Instructions
6 PACKAGING INFORMATION AND PRODUCTION INSTRUCTIONS 6 Packaging information and production instructions 6.1 Mechanical Dimensions Figure 3 Mechanical dimensions of TYZS11 15 / 24... -
Page 18: Recommended Pcb Encapsulation
6 PACKAGING INFORMATION AND PRODUCTION INSTRUCTIONS 6.2 Recommended PCB Encapsulation Figure 4 TYZS11 schematic diagram and pin connection Comply with the encapsulation diagram provided in Figure 5. 16 / 24... -
Page 19: Production Instructions
6 PACKAGING INFORMATION AND PRODUCTION INSTRUCTIONS Figure 5 Encapsulation diagram of TYZS11 6.3 Production Instructions • The stamp-hole module must be mounted by the SMT machine. After being unpacked, it must be soldered within 24 hours. Otherwise, it must be put into... - Page 20 6 PACKAGING INFORMATION AND PRODUCTION INSTRUCTIONS (the total exposure time cannot exceed 168 hours). – SMT equipment: ∗ Mounter ∗ SPI ∗ Reflow soldering machine ∗ Oven temperature tester ∗ Automated optical inspection (AOI) equipment – Baking equipment: ∗ Cabinet oven ∗...
-
Page 21: Recommended Oven Temperature Curve
6 PACKAGING INFORMATION AND PRODUCTION INSTRUCTIONS – Time: 48 hours for reelizing and 12 hours for palletizing – Alarm temperature: 65°C for reelizing and 135°C for palletizing – Production ready temperature after natural cooling: < 36°C – The number of drying times: 1 –... - Page 22 6 PACKAGING INFORMATION AND PRODUCTION INSTRUCTIONS • A: Temperature axis • B: Time axis • C: Liquidus temperature: 217 to 220°C • D: Ramp-up slope: 1 to 3°C/s • E: Duration of constant temperature: 60 to 120s; the range of constant tem- perature: 150 to 200°C •...
-
Page 23: Storage Conditions
6 PACKAGING INFORMATION AND PRODUCTION INSTRUCTIONS 6.5 Storage conditions 21 / 24... -
Page 24: Appendix: Statement
7 APPENDIX: STATEMENT 7 Appendix: Statement FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. - Page 25 “This product must be installed and operated with a minimum distance of 20 cm between the radiator and user body”. This device has got an FCC ID: 2ANDL-TYZS11. The end product must be labeled in a visible area with the following: “Contains Transmitter Module FCC ID: 2ANDL- TYZS11”.
- Page 26 7 APPENDIX: STATEMENT This product must not be disposed of as normal household waste, in accordance with the EU directive for waste electrical and electronic equipment (WEEE-2012/19/EU). Instead, it should be disposed of by returning it to the point of sale, or to a municipal recycling collection point.
Need help?
Do you have a question about the TYZS11 and is the answer not in the manual?
Questions and answers