Setting The Spray Gun; Setting The Required Spray Pattern; Setting The Amount Of Material; Setting The Amount Of Air - WAGNER FINISH CONTROL 3500 Operating Manual

GB
SETTING THE SPRAY GUN /STARTING OPERATION/
Mordants, glazes, im- undiluted
pregnations, oils
Clear varnishes, syn- observe manufa -
theti enamels, ol- turer's instru tions
oured paints, alkyd
resin varnishes
Primers, radiator observe manufa -
paints, hammer ef- turer's instru tions
fe t enamels
Anti-rust paints, spe- observe manufa -
ial-effe t paints turer's instru tions
Multi olor paints, observe manufa -
textured paints turer's instru tions
7

SETTING THE SPRAY GUN

7.1

SETTING THE REQUIRED SPRAY PATTERN

Attention:
Never pull trigger while adjusting the air
cap settings.
The alignment of the spray jet an be determined by turning
the bla k adjusting ring (Fig. 3, 1).
A horizontal flat jet
B vertical flat jet
It is also possible to swit h between a wide ( ) and a ompa t
( ) spray jet with the adjusting lever (Fig. 4, 1).
7.2 SETTING THE AMOUNT OF MATERIAL (FIG. 5)
The material volume an be adjusted in rementally from 1
(minimum) to 12 (maximum) by turning the material volume
ontrol (Fig. 5, 1).
7.3 SETTING THE AMOUNT OF AIR (FIG. 6)
Turn the air volume ontrol (Fig, 6, 1) lo kwise to in rease the
air volume or anti- lo kwise to redu e the air volume (note
arrow on body of gun).
Setting the air and paint flow rate orre tly is im-
portant for atomisation, overspray and working
speed.
20
FineSpray spray
atta hment
(brown) re om-
mended
WallSpray spray
atta hment
(white) re om-
mended
for verti al surfa es
for horizontal surfa es
7.4

ALIGN THE FEED TUBE

If the feed tube is positioned
ontents an be sprayed without almost any residue.
When working on lying obje ts:
Turn the feed tube forwards. (Fig. 7 A)
Spraying work when working on overhead obje ts:
Turn the feed tube rearwards. (Fig. 7 B)
8

STARTING OPERATION

Before onne ting to the
mains supply make sure that
the mains voltage orre-
sponds to the operating volt-
age on the rating plate. The
unit must be onne ted with
a properly earthed sho k-
proof so ket.
1. Uns rew the ontainer from the spray atta hment.
2. Pour in the prepared oating material.
Fill the ontainer
with maximum
1000 ml.
3. Fit the appropriate filter to the feed tube depending on the
oating material used (Fig. 9, 1)
Low-vis osity oating materials
Vis ous oating materials
4. Align the feed tube. (Fig. 7)
5. S rew the ontainer firmly onto the spray atta hment.
6. Conne t spray atta hment and FC 3500. (Fig. 2)
When working with the FC 3500 we re ommend
using the supplied arrying strap. This enables the
weight of the FC 3500 to be better distributed and
the work an be arried out with less effort.
7. Both arabiner lo ks on the arrying strap have to be
se ured to the fixture. (Fig. 8)
The fixture for the arrying strap an be mounted
to the other side of the FC 3500 if this is preferred.
Do this by uns rewing the two large s rews (fig. 8,
1). Mount the fixture to the other side by inserting
the s rews into the relevant holes. Please make
sure that you use only the screws that have
been provided. Screws of the wrong length or
diameter can damage the device. Never tighten
the screws without the fixture.
8. Plug in the power able.
9. The devi e is now ready for operation.
FinishControl 3500
orre tly, the
1000ml
Fine filter (red)
Coarse filter (white)
ontainer