EINHELL FREELEXO LCD BT+ Original Operating Instructions page 40

.2 Control panel
The robot lawn mower has already been pro-
grammed at the factory and default settings have
been made for it. However, these can be changed
if required. Even though the factory settings will
be suitable for most gardens, you should still
familiarize yourself with the available options ne-
vertheless.
Explanation of the control panel with LCD
(Fig. 9)
50. LCD
51. "SET" button
52. "MODE" button
53. "START" button
54. "BACK" button
55. Navigation buttons
56. "OK" button
6.3 Cutting height adjustment facility
Important! Adjust the cutting height only when
the robot lawn mower has been switched off . Do
this by pressing the STOP button (3). The cutting
height adjustment facility (4) allows the cutting
height of the robot lawn mower to be set to infi ni-
tely adjustable settings between 20 and 60 mm,
which can be viewed on the scale.
If the grass is taller than 60 mm it has to be shor-
tened to a maximum of 60 mm fi rst to avoid expo-
sing the robot lawn mower to excessive load and
adversely aff ecting its operating effi ciency. Use a
conventional lawn mower or trimmer to do this.
After installation has been completed, the cutting
height can be adjusted using the cutting height
adjustment facility (4). Always start with a higher
cutting height and reduce it in small steps until
you reach the desired height.
6.4 Locking mechanism / PIN
The locking mechanism prevents the unautho-
rized use of the robot lawn mower without a valid
code. You have to enter a personal four-digit secu-
rity code for this.
Lock release
Before you start using the robot lawn mower, you
have to enter the correct PIN (standard PIN: "0-0-
0-0"). Enter the PIN with the help of the navigation
buttons (55).
Standard PIN: New PIN:
0 0 0 0 _ _ _ _
Changing the PIN
To change the PIN, proceed as follows.
Anl_FREELEXO_LCD_BT_plus_SPK13.indb 40 Anl_FREELEXO_LCD_BT_plus_SPK13.indb 40
GB
1. Unlock the control panel.
2. First press the "SET" button (51) in order to
make your settings.
3. Use the navigation buttons (55) to navigate in
the menu on the LCD (50) to the point "Gene-
ral information" and then „PIN code".
4. First enter the current PIN (standard PIN 0-0-
0-0) with the help of the navigation buttons
(55).
5. Then use the navigation buttons (55) to enter
your personal PIN.
6. Confi rm the settings you have just made.
7. Repeat step 5. and step 6 in order to confi rm
the new PIN.
8. Important! Make a note of the new PIN.
Requesting your PIN if you lose it
Have the receipt and the serial number of the
robot lawn mower ready. You need them in order
to get your PIN.
Version A:
1. Press and hold the „SET" button (51) for 6
seconds in locked status.
2. The PUK will now appear in the display (50).
3. Contact the customer services team to obtain
your PIN.
Version B:
1. Connect an empty USB stick to the USB con-
nection (26) as shown (Fig. 11).
2. Switch on the main switch (7) (ON).
3. The robot lawn mower will automatically save
the PUK to your USB stick and will then end
the operation with a beep.
4. Pull out the USB stick. Import the data from
the USB stick to a computer. A text fi le (*.txt)
will have been created by the robot lawn
mower. This fi le contains a PUK, a personal
code. Please contact the customer services
team to obtain your PIN.
6.5 Settings of the robot lawn mower
The main menu on the LCD (50) shows you the
current date and time settings of the robot lawn
mower, as well as the current charge level. At the
same time the status of the rain sensor and of the
wire signal and of the selected mowing program
will appear in the toolbar. On the control panel
you can use either the "SET" button (51) to make
settings on the robot lawn mower or the "MODE"
button (52) to start the robot lawn mower with
various mowing programs. Use the navigation
buttons (55) to go to the option where you want to
make the settings. Press the "BACK" button (54)
in order to exit the respective menu.
- 40 -
24.03.2022 12:39:45 24.03.2022 12:39:45