Output Terminals - Sanyo SRT-2400 Instruction Manual

OUTPUT TERMINALS

TAPE END OUT Terminal
During recording, when the end of the tape is reached
or when the tape counter reading indicates 7 hours 57
minutes or more, the output becomes 0V (Low).
To reset the output, press the STOP or EJECT button.
During autorepeat recording, when the end of the tape
is reached, the output becomes 0V (Low) for about 2
seconds only.
Tape end or 7:57:00
Output reset
TAPE END OUT Terminal Output Setting
1
Press the MENU button until the (SET UP 3) menu is
displayed.
@@@@@@@<SET@UP@3>
*ALARM@MODE@@@@@@@Y1
*ALARM@SPEED@@@@@@8H
*ALARM@DURATION@@@20S
*VERTICAL@SYNC@@@@Y
*EXT@TIME@ADJ.@@@@01:00
*TAPE@IN@MODE@@@@@STOP
*TAPE@END@MODE@@@@REW
*TAPE@END@OUT@@@@@-3M
*CLOG@DETECT.@@@@@Y
*SERIES@REC@IN@@@@N
2
Press the ] button until the "TAPE END OUT" setting
is flashing.
3
Press the l (or j) button, to select the desired
output mode.
–3M . . . . . . . . The output becomes 0 V (Low)
when the tape counter reaches
"7:57:00" and/or when the tape
reaches the end.
END . . . . . . . . The output becomes 0 V (Low)
when the tape reaches the end.
4
Press the PAUSE/SEARCH button to save the setting.
5V (H)
(Output impedance: 5.7 k )
0V (L)
SW OUT Terminal
When recording, a pulse signal is output at the SW OUT
terminal.
This terminal is usually connected to the switch input (SW
IN) of devices like a camera switcher unit, or a quad
compressor.
FIELD: 16.7 msec.
FRAME: 5 msec.
SW OUT Terminal Output Setting
1
Press the MENU button until the (SET UP 4) menu is
displayed.
@@@@@@@<SET@UP@4>
*SW@OUT
@@TIMING@@@@@@@@@@FIELD
@@FIELD@@@@@@@@@@@01
@@8H@@@@@@@@@@@@@@Y
*THREAD@CHECK@@@@@Y
*VIDEO@LOSS@@@@@@@N
*REC@SPEED@@@@@@@@N
*EJECT@SET
@@EJECT@MODE@@@@@@EJECT1
@@OPERATION@@@@@@@SLAVE
2
Press the l (or j) button to set "FIELD" or "FRAME",
then press the ] button.
FIELD . . . . . . . 1 pulse is output after each set
FRAME. . . . . . 1 pulse is output after each set
3
Press the l (or j) button to set the desired pulse
signal interval, then press the ] button.
If "TIMING" is set to FRAME (see step 4),
"FRAME" will be indicated instead of "FIELD".
Available settings are:
FIELD . . . . . . . 01, 02, 03, 04, 05, 10, 30 or 60 field
FRAME. . . . . . 01, 02, 03, 04, 05, 10, 30 or 60
4
Press the l (or j) button to set the desired "8H (or
6H)" mode.
If the"TAPE" in the (SET UP 5) menu is set to
"T-120", "6H" will be indicated instead of "8H".
Y . . . . . . . . . . . When recording in 8-hour (or
N. . . . . . . . . . . When recording in 8-hour (or
5
Press the PAUSE/SEARCH button to save the
settings.
40
5V (H)
(Output impedance: 5.7 k )
0V (L)
number of fields.
number of frames.
frame
6-hour) mode, a pulse signal is
output.
6-hour) mode, a pulse signal is
not output.
English