Related Manuals for Clarke PANTHER 9/25
Summary of Contents for Clarke PANTHER 9/25
- Page 1 24L AIR COMPRESSOR MODEL NO: PANTHER 9/25 PART NO: 2242110 OPERATION & MAINTENANCE INSTRUCTIONS GC0522 - rev 1 ORIGINAL INSTRUCTIONS...
-
Page 2: Environmental Recycling Policy
INTRODUCTION Thank you for purchasing this CLARKE 24L Air Compressor. Read this manual fully before use and follow the instructions carefully. In doing so you will ensure the safety of yourself and those around you and you can look forward to your purchase giving you long and satisfactory service. -
Page 3: Safety Precautions
2. DO NOT operate your compressor with the guard removed. 3. Repairs must only be carried out by a qualified engineer. If problems occur, contact your nearest Clarke dealer. 4. Before carrying out any maintenance, make sure that the pressure is released from the air tank and that the compressor is disconnected from the electrical supply. -
Page 4: Safety Symbols
SAFETY SYMBOLS Read this instruction booklet carefully before positioning, operating or adjusting the compressor. This compressor contains surfaces which may reach a high temperature during operation. Never operate with the motor housing removed. Wear safety goggles when using this compressor Wear ear protectors when using this compressor This compressor produces a high sound level during operation. -
Page 5: Electrical Connections
ELECTRICAL CONNECTIONS WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY. Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply through an approved 13 amp BS 1363 plug, or a suitably fused isolator switch. If the plug has to be changed because it is not suitable for your socket, or because of damage, it must be removed and a replacement fitted, following the wiring instructions shown below. -
Page 6: Attach The Wheels
ASSEMBLY ATTACH THE WHEELS Use a spanner to attach the wheels to the compressor. Use the washers and spring washer in the positions shown. ATTACH THE FOOT Insert the foot into the position shown. ATTACH THE AIR FILTER 1. Screw the air filter into position. •... -
Page 7: Install The Oil Breather Cap
INSTALL THE OIL BREATHER CAP 1. Remove the travel plug. 2. Insert the oil breather cap. MOVING THE COMPRESSOR CAUTION: THE COMPRESSOR IS HEAVY AND REQUIRES TWO PEOPLE TO LIFT SAFELY. • Stop the compressor and disconnect it from the power supply before you move it. -
Page 8: Before Use
2. If not, remove the oil cap and add oil to the reservoir. • Only use SAE30 compressor oil, available from your Clarke dealer. • Only fill to the half way point on the sight glass, overfilling may result in damage. -
Page 9: Operation
OPERATION If the compressor has not been used for more than 24 hours, open the drain valve on the bottom of the tank, and drain any condensate which has collected. See page 12. ATTACHING AIR TOOLS WARNING: BEFORE CONNECTING AIR TOOLS, MAKE SURE THAT YOU READ THE INSTRUCTIONS SUPPLIED WITH THE TOOL, ALSO ENSURE THAT THE TOOL IS SUITABLE FOR USE WITH THE COMPRESSOR AND HOSE SPECIFICATIONS. -
Page 10: Check The Safety Valve
CHECK THE SAFETY VALVE To make sure that the safety valve works correctly: 1. Unscrew the knurled end and pull it firmly outwards. • Air will be released when you pull the cap out and stop when released. 2. If the valve does not operate, do not use the compressor. -
Page 11: Remove Tools From The Air Hose
REMOVE TOOLS FROM THE AIR HOSE WARNING: ALWAYS SET THE PRESSURE REGULATOR TO ZERO BEFORE YOU REMOVE OR REPLACE A TOOL. 1. Push down on the On/Off button to stop the compressor. 2. Turn the outlet valve handle to the closed position. -
Page 12: Draining The Tank
If you start the compressor and the overload cutout operates again, stop the compressor and disconnect from the power supply and have your compressor examined by a Clarke service agent. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 13: Maintenance
2. If not, remove the oil breather cap and add oil to the reservoir. • Only use SAE30 compressor oil, available from your nearest Clarke dealer. DRAIN THE TANK (DAILY) After use, always open the drain valve to make sure that any condensate is drained off. -
Page 14: Check The Non-Return Valve (Every 6 Months)
CHECK THE NON-RETURN VALVE (EVERY 6 MONTHS) If the tank pressure decreases for no apparent reason, it is possible that the non-return valve is leaking. To check, 1. Make sure that the tank is not under pressure and the compressor is switched OFF. 2. -
Page 15: Specifications
SPECIFICATIONS Max Pressure 8 Bar / 116PSI Voltage 230 VAC (50Hz) Output Power 1800W / 2.5HP Air Displacement 9.3 CFM (262 l/min) Receiver Capacity 24 L Fuse Rating 13 A Dimensions (L x W x H) 560 x 355 x 595 mm Guaranteed Sound Power Level 97 dB(A) Weight... -
Page 16: Troubleshooting
1. Switch off and wait approx has tripped. 5 minutes. 2. Press the reset button and switch on again. Motor windings burnt out. 1. Contact your Clarke dealer for a replacement motor. The compressor Compressor head gasket 1. Return the compressor to does not reach blown or valve broken. -
Page 17: Component Parts
COMPONENT PARTS Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 18: Component Parts List
COMPONENT PARTS LIST Crankcase Cylinder Head Air Reservoir Crankshaft Flat Washer Hole Plug Connecting rod Spring Washer Drain Valve Screw Bolt Gasket Elbow Flat Washer Crankcase cover Sping Washer Sightglass oil seal Capacitor Foot Sightglass Overload Protector Screw Screw Flat Washer Oil breather Spring Washer Flat Washer... -
Page 19: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...