Download Print this page
MUTOH VJ-426UF Maintenance Sheet
Hide thumbs Also See for VJ-426UF:

Advertisement

Quick Links

Daily Maintenance Sheet for VJ-426UF
Daily maintenance
The content of this documents are based on the specification of the firmware Ver.1.05 or later.
When to maintain:
After operation (Be sure to perform the following maintenance)
When the media strikes the print head
Required Items:
(a) Plastic gloves (Supplied accessories or
Commercial item)
(b) Rubber gloves (Supplied accessories or
Commercial item)
(c) Protective goggles (Supplied accessories)
(d) Paper towel (Supplied accessories)
or Polyester knit wiper (Optional accessories)
(e) Dropper (Supplied accessories)
(f ) Dedicated maintenance cleaner (Optional
accessories)
(g) Plastic cup (Supplied accessories)
(h) Cleaning stick (Supplied accessories or Optional
accessories)
(i) Tray (Supplied accessories)
(j) Scraper (Supplied accessories)
Use a paper towel supplied with the printer or optional
Polyester knit wiper. DO NOT use a tissue.
Lints or flakes on tissue may cause damage to the print head.
DO NOT use non-dedicated maintenance cleaner.
CS3007-03
a
c
b
f
d
e
g
h
i
j
Preparation:
Wear the rubber gloves (white) over the plastic
gloves (pink).
Wear protective goggles.
CAUTION
Skin or eye contact with UV curable ink may cause skin
inflammation or allergic reaction.
For this operation, be sure to wear the supplied gloves
(or solvent resistant gloves) and goggles to prevent ink
from contacting with your eyes or skin.
Important!
Before performing maintenance, make sure to read
"How to handle UV inkjet printer / its supplies"
(supplied with the printer).
Press the [MENU] key on the operation panel.
Press the [+] / [-] key on the operation panel to select [Menu 5: Sleep Mode >].
Press the [>] key on the operation panel.
When [Sleep Mode 1: Start] appears on the operation panel, press the [Enter] key.
When [Start Sleep Mode?] appears on the operation panel, press the [Enter] key.
When [Daily Maint.: Start] appears on the operation panel, press the [Enter] key.
When [Remove Media -> E] appears on the operation panel, remove the media and the jig
on the table, and then press the [Enter] key.
When [Daily Maint.: End] appears on the operation panel, you can start the maintenance
with following steps.
Make sure to complete this maintenance within 5 minutes while the printer is in Daily maintenance state.
-1-

Advertisement

loading
Need help?

Need help?

Do you have a question about the VJ-426UF and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for MUTOH VJ-426UF

  • Page 1 Daily Maintenance Sheet for VJ-426UF Daily maintenance The content of this documents are based on the specification of the firmware Ver.1.05 or later. When to maintain: Preparation: After operation (Be sure to perform the following maintenance) Wear the rubber gloves (white) over the plastic When the media strikes the print head gloves (pink).
  • Page 2 Cleaning of UV Lamp Moistening the surface of print head nozzles Important! Open the front cover slowly, holding it by the During cleaning, please note the followings: places shown in the picture and using both • Always follow this steps to perform daily maintenance. hands.
  • Page 3 Cleaning of print head circumference Cleaning of cleaning wiper and the circumference of the cap Look at the bottom side of the carriage. Use the cleaning stick to clean the left side Check if dusts and ink deposit are adhered. surface of the cleaning wiper (a black rubber part).
  • Page 4 Do not reuse a cleaning stick. Dusts can adhere causing damage to the print head. Check that the lid of the maintenance cleaner is shut properly and store it. For purchasing the maintenance items, contact your local Mutoh dealer or nearest Mutoh sales office. Name Part Number Minimum q’ty per order...
  • Page 5 Czyszczenie, Konserwacja, Wymiana części eksploatacyjnych. Wymagania ogólne Niezależnie od informacji i zaleceń zawartych w powyższej instrukcji należy czyścić dane części (jeśli urządzenie je posiada) nie rzadziej, niż w podanej poniżej częstotliwości. Ponadto należy codziennie przeprowadzać kontrolę zabrudzenia poszczególnych części i przeprowadzać ich czyszczenie jeśli ulegną zabrudzeniu.