Advertisement
Quick Links
Advertisement
Related Manuals for TRIBU SENJA
Summary of Contents for TRIBU SENJA
- Page 1 SESO01 - 22-11-2018 ASSEMBLY INSTRUCTIONS SENJA SOFA...
- Page 2 COMPONENTS FRAME CONNECTION alu / teak Regular / Deep Components for back- and armrest: ARMREST / BACKREST CLAMP High / Low Regular / Deep Components for the console table: CONSOLE TABLE SUPPORT HIGH LEGS lava stone / teak...
- Page 3 COMPONENTS Components for the side table: SIDE TABLE TABLE LEG lava stone / teak Components for the table: TABLE TABLE SUPPORT lava stone / teak Hardware: LARGE SCREW SMALL SCREW BUTTON SCREW countersunk countersunk buttonhead WOOD SCREW FLAT SCREW WASHER flathead...
- Page 4 ASSEMBLY INSTRUCTIONS Put the FRAME upside down on a protective cover. Attach the LEGS to the frame by turning them clockwise. Repeat this step for each FRAME. Use 2 LARGE SCREW to mount 2 CLAMPS to each ARM/BACKREST provided. To secure the CLAMPS to the ARM/BACKRESTturn the LARGE SCREWS clockwise and tighten for 90%.
- Page 5 If you only have 1 FRAME proceed to step 4. If you have multiple FRAMES put them in the desired position. Once they are in the correct position attach them to each other with the connector. To secure the CONNECTION put 2 SMALL SCREWS in the designated holes and turn them clockwise.
- Page 6 Put the CLAMPS on the frame in a way the hole of the CLAMP and the frame align. Once aligned, secure the CLAMP by inserting a SMALL SCREW and turning it clockwise. Repeat for the other CLAMP. Tighten the BIG SCREWS 100%...
- Page 7 Repeat steps 5 + 6 for each individual arm/backrest. If your Senja sofa has the following components, continue to the corresponding step. Side table: step Table: step Console table: step If you don’t have any of these components, proceed to step...
- Page 8 Mount the SIDE TABLE on top of the TABLE LEG by using 4 BUTTON SCREWS. Turn clockwise to tighten. To mount the assembled SIDE TABLE to the FRAME remove the headless plastic screws in the FRAME there where you want your SIDE TABLE.
- Page 9 To secure the assembled SIDE TABLE to the frame, allign the hole in the CLAMP and the hole in the FRAME. Use a SMALL SCREW and tighten it by turning it clockwise. To install a TABLE, you need to install 2 SUPPORTS first. Remove headless screws first.
- Page 10 Place the TABLE on top of the TABLE SUPPORT. If it is a TEAK table use 4 WOOD SCREWS, if it is a LAVE STONE table use 4 BUTTON SCREWS. To secure the table turn the screws clockwise.
- Page 11 To install a CONSOLE TABLE, you need to install the HIGH LEGS + SUP- PORT first.To attach the HIGH LEGS to the FRAME make sure there are only 2 LEGS attached to the FRAME. Slide the HIGH LEGS under the frame. Make sure the hole in the HIGH LEGS which is the farthest from the post aligns with the holes in the center of the FRAME.
- Page 12 To secure the HIGH LEGS to the FRAME use 2 LONG SCREWS and 2 WASHERS per HIGH LEG. Slide the FLAT SCREWS through the WASHERS and into the designated holes. Turn them clockwise to tighten. Place the SUPPORT on top of the HIGH LEGS, make sure the hole in the SUPPORT aligns with the hole in the HIGH LEGS.
- Page 13 Carefully place the CONSOLE TABLE on top of the SUPPORT, align the holes in the CONSOLE TABLE with the holes in the SUPPORT. Use 4 BUT- TON SCREWS to secure them together.
- Page 14 Place the seat cushion in position by alligning the edge of the seat cushion with the edge of the frame. To fix the cushion into place, attach the velcro strips to each other. Make sure that the velcro straps are on the front side of the sofa.
- Page 15 Slide the cushions over the ARM/BACKREST. Make sure the letter on the label (inside of the pillow) matches the letter on the arm/backrest. The label must always be on the outside of the sofa.
- Page 16 Tribù nv Oude Heidestraat 72 3740 Bilzen BELGIUM www.tribu.com info@tribu.com...
Need help?
Do you have a question about the SENJA and is the answer not in the manual?
Questions and answers