Roland RD-700NX Owner's Manual page 92

Problem
Pitch is Odd
Sound is Cut Off
Sound continues even after removing
fingers from keys
Exclusive Messages Cannot Be Received
Song Data Not Played Back Correctly
Pedal function is not affected
[S1] [S2] buttons' function is not
affected
Nothing appears in the screen
Vertical lines appear in the screen/
Color is "washed out" at the edges of
the screen
Screen display is irregular when power
is turned on/off
Pedal does not work, or is "stuck"/Pedal
does not operate correctly
Can't read or write USB memory
successfully
Reverberation remains even if you
defeat the Reverb effect
Check/Solution
Depending on the Tone selected, pitches played in certain registers will be changed
and played at other pitches.
Is Coarse Tune or Fine Tune set for any specific Part?
Check the following settings.
• TONE EDIT Course Tune, Fine Tune
• C.T and F.T setting in MIDI screen
Has the RD-700NX gone out of tune?
Check the following settings.
• System Master Tune settings in Edit mode
• System Temperament settings in Edit mode
• Micro Tune settings in Piano Tone Edit mode
Has the pitch been changed by pedal operations or by Pitch Bend messages received
from an external MIDI device?
Have you set Transpose?
When you try playing more than the maximum 128 voices simultaneously, sounds
currently being played may be cut out.
Increase the Voice Reserve settings for the Parts you do not want to have cut off.
Is the pedal polarity reversed?
Check the System Pedal Polarity settings in Edit mode.
Is the Device ID number of the transmitting device matched to the RD-700NX's Device
ID number?
Make sure that the transmitting unit is set to Device ID number 17.
Is the Receive GM/GM2 System On Switch set to ON?
Set the System Rx GM System On or System Rx GM2 System On to ON in Edit mode.
Are you playing back GS Format song data?
Once the RD-700NX receives a GS Reset message, it then is enabled for GS Format. This
permits playback of music files bearing the GS logo (GS music files). However, data
created exclusively for the Sound Canvas Series may not play back properly on the
RD-700NX.
Is the audio data playable?
Make sure that the audio data can be played by the RD-700NX.
Is the System Pedal Mode setting in Edit mode set to "SYSTEM"?
Set this to "Live Set".
Is the System S1/S2 Mode setting in Edit mode set to "SYSTEM"?
Set this to "Live Set".
Since the RD-700NX uses a liquid crystal screen, it may happen that no text or graphics
appear in the screen if the temperature is below zero degrees Celsius (32 degrees
Fahrenheit).
These occur due to the nature of a liquid crystal display, and do not indicate a
malfunction.
They can be minimized by adjusting the contrast of the screen.
This is due to the nature of an LCD screen; it does not indicate a malfunction.
Is the pedal connected correctly?
Plug the cord firmly into the pedal jack.
Are you using a pedal made by another manufacturer?
Use the pedal included with the RD-700NX or an optional DP Series or similar pedal.
Are you using (optional) Roland USB memory?
Reliable performance cannot be guaranteed if you use non-Roland USB memory
products.
If you are unable to read or write USB memory successfully, change the USB Memory
Mode setting.
The RD-700NX's piano sound faithfully simulates the depth and resonance of an
acoustic piano, and this may give the impression of reverberation even if you've
defeated the Reverb effect.
Material
Page
–
p. 54
p. 63
p. 67
p. 70
p. 48
–
p. 32
p. 57
p. 69
–
p. 70
–
p. 95
p. 67
p. 68
–
–
–
p. 16
p. 15
–
p. 69
–
93