Crestron CAEN-UMP1X2-DIN-PWS Product Manual
Crestron CAEN-UMP1X2-DIN-PWS Product Manual

Crestron CAEN-UMP1X2-DIN-PWS Product Manual

Automation enclosure mounting kit
Hide thumbs Also See for CAEN-UMP1X2-DIN-PWS:

Advertisement

Quick Links

CAEN-UMP1X2-DIN-PWS
CAEN Automation Enclosure Mounting Kit
for 4-Series™ Automation Processor and Hub
Product Manual
Crestron Electronics, Inc.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CAEN-UMP1X2-DIN-PWS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Crestron CAEN-UMP1X2-DIN-PWS

  • Page 1 CAEN-UMP1X2-DIN-PWS CAEN Automation Enclosure Mounting Kit for 4-Series™ Automation Processor and Hub Product Manual Crestron Electronics, Inc.
  • Page 2 Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
  • Page 3: Table Of Contents

    Install the DIN-AP4 Wire the DIN Rail Products Mount the Plate to an Enclosure Wire the CLX and DIN Rail Products Resources Crestron Support and Training Programmer and Developer Resources Product Certificates Related Documentation Product Manual — Doc. 9310A Contents • iii...
  • Page 4 iv • Contents Product Manual — Doc. 9310A...
  • Page 5: Overview

    (sold separately). The CAEN-UMP1X2 mounting plate is equipped with a DIN rail and a DIN-PWS30-277 30 W Cresnet® power supply. The CAEN-UMP1X2-DIN-PWS also includes DIN rail end clamps, screws, and cables for connecting the DIN products. For additional details, refer to the...
  • Page 6: Specifications

    Specifications Product specifications for the CAEN-UMP1X2-DIN-PWS. Product Specifications Power Main Power 100-277VAC, 50/60 Hz Available Power 30 W maximum from the DIN-PWS30-277 Environmental Temperature 41° to 113 °F (5° to 45 °C) Humidity 10% to 90% RH (noncondensing) Enclosure Mounting Plate: Metal with attached DIN rail and tie-down anchors...
  • Page 7: Dimension Drawings

    Dimension Drawings Product Manual — Doc. 9310A CAEN-UMP1X2-DIN-PWS • 7...
  • Page 8: Installation

    Installation The CAEN-UMP1X2-DIN-PWS mounting kit is comprised of a CAEN-UMP1X2 mounting plate with a preinstalled DIN rail and DIN-PWS30-277 power supply. The following sections discuss how to connect a DIN-HUB DIN-AP4 (both sold separately). NOTE: Before installing DIN products, use a small flat-head screwdriver to loosen the end clamp screw, then remove the end clamp.
  • Page 9: Install The Din-Hub

    Install the DIN-HUB The DIN-HUB is not included with the CAEN-UMP1X2-DIN-PWS. Included equipment to prepare the DIN-HUB: Three 3-pin terminal blocks (included with the DIN-HUB) Eight 4-pin terminal blocks (included with the DIN-HUB) Three jumper wires (included with the CAEN-UMP1X2-DIN-PWS) To install the DIN-HUB: 1.
  • Page 10: Install The Din-Ap4

    Installation guide for details. 6. Connect the remaining terminal blocks or save them for future use. Install the DIN-AP4 The DIN-AP4 is not included with the CAEN-UMP1X2-DIN-PWS. Included equipment with the DIN-AP4: One 2-Pin terminal block Two 4-Pin terminal blocks...
  • Page 11: Wire The Din Rail Products

    To connect the DIN products, use the following equipment included with the CAEN-UMP1X2-DIN-PWS: 2-wire cable with flying leads on one end and a 2-pin terminal block on the other 4-wire cable with 4-pin connectors Two tie wraps Product Manual — Doc. 9310A CAEN-UMP1X2-DIN-PWS • 11...
  • Page 12 2. Connect the NET output on the DIN-AP4 to the NET HOST input on the DIN-HUB using the 4-wire cable. Match the terminals for both devices: 3. Use the tie wraps to secure loose wires from steps 1 and 2. Cut off any excess of the wrap. 12 • CAEN-UMP1X2-DIN-PWS Product Manual — Doc. 9310A...
  • Page 13: Mount The Plate To An Enclosure

    Use a Phillips screwdriver to secure the screw to the UMP1X2 plate. Tighten to 9 in.-lbs (1.02 nm). Mount the Plate to an Enclosure To mount the CAEN-UMP1X2-DIN-PWS to a CAEN, CAEN-MLO, or CAENIB automation enclosure (sold separately): Product Manual — Doc. 9310A...
  • Page 14 Using the remaining four screws, attach the CAEN-UMP1X2-DIN-PWS to the enclosure. Ensure the flanges of the plates do not overlap other plates or lighting modules that are mounted in the enclosure. NOTE: In a single-wide enclosure, install the CAEN-UMP1X2-DIN-PWS in the bottom module position.
  • Page 15 Refer to the following diagrams for example CAEN-UMP1X2-DIN-PWS placement in an enclosure. CAEN-UMP1X2-DIN-PWS in a 2x1 Enclosure Product Manual — Doc. 9310A CAEN-UMP1X2-DIN-PWS • 15...
  • Page 16: Wire The Clx And Din Rail Products

    CAEN-UMP1X2-DIN-PWS in a 7x2 Enclosure Wire the CLX and DIN Rail Products Make connections to the CAEN-BLOCK (sold separately), CLX module (sold separately), DIN-PWS30-277, DIN-AP4, and DIN-HUB. WARNING: To avoid fire, shock, or death, turn off power at circuit breaker or fuse and test...
  • Page 17 1. Connect the following cables included with the CAEN-UMP1X2-DIN-PWS. The 6 in. (153 mm) cable connects a CAEN-BLOCK Cresnet port to the DIN-AP4 Cresnet port. The 18 in. (457 mm) flat cable connects the CAEN-BLOCK to the CLX module connector.
  • Page 18 NOTE: The DIN-HUB and CAEN-BLOCK only receive power when powered via the DIN-PWS30-277. If the DIN-AP4 is powered via PoE (not recommended), it will not pass power to the DIN-HUB or CAEN-BLOCK. 3. Wire the CAEN-UMP1X2-DIN-PWS. Refer to the DIN-AP4 DIN-HUB manuals.
  • Page 19: Resources

    Resources The following resources are provided for the CAEN-UMP1X2-DIN-PWS. NOTE: You may need to provide your Crestron.com web account credentials when prompted to access some of the following resources. Crestron Support and Training Crestron True Blue Support Crestron Resource Library Crestron Online Help (OLH) Crestron Training Institute (CTI) Portal...
  • Page 20 Product Manual — Doc. 9310A Crestron Electronics, Inc. (2054547) 15 Volvo Drive, Rockleigh, NJ 07647 06/15/22 Tel: 888.CRESTRON Specifications subject to Fax: 201.767.7656 change without notice. www.crestron.com...

Table of Contents