Connecting To The Battery; Charging Modes - BorMann BBC4030 Manual

EN
LCD ICONS:

Connecting to the battery

1. Identify the polarity of battery posts. The positive battery terminal is typically marked by these letters or symbols (POS,P,+). The negative battery terminal is
typically marked by these letters or symbols (NEG,N,-).
2. Do not make any connections to the carburetor, fuel lines, or thin metal parts.
3. Identify if you have a negative or positive grounded vehicle. This can be done by identifying which battery post (NEG or POS) is connected to the chassis.
4. For a negative grounded vehicle (most common): connect the RED POSITIVE clamp first to the positive battery terminal, then connect the BLACK NEGATIVE
clamp to the negative battery terminal or vehicle chassis.
5. For a positive grounded vehicle (very uncommon): connect the BLACK NEGATIVE clamp first to the negative battery terminal, then connect the RED POSITIVE
clamp to the positive battery terminal or vehicle chassis.
6. When disconnecting, disconnect in the reverse sequence, removing the negative first (or positive first for positive ground systems).
7. A marine (boat) battery must be removed and charged on shore. To charge it on board requires equipment specially designed for marine use.

Charging modes

Ιmportant Note:
The BBC4030 charger has 13 modes: Standby, 12V STD, 12V COLD/AGM, 12V LITHIUM (LIFEPO4), 12V CAL, 24V STD, 24V COLD/AGM, 24V CAL , 13,6V SUPPLY,
REPAIR, 12V BOOST, 12V ALTERNATOR CHECK, BATTERY HEALTH CHECK. Do not operate the charger until you confirm the appropriate charge mode for your
battery. CAUTION: If you choose 24V Mode(s) for 12V battery, the 12V battery will be damaged!
Mode Battery Size (Ah)
Standby
12 V STD
12 V COLD/AGM
12 V CAL
24 V STD
24 V COLD/AGM
24 V CAL
12 V LITHIUM
REPAIR
13,6 V SUPPLY
12 V BOOST
12V ALTERNATOR CHECK
BATTERY HEALTH
CHECK
The following modes are advanced charging modes that require your full attention before selecting.
3
Battery CCA detection display / battery voltage display / battery function display
Battery repair
function
Battery voltage
type display
Battery health
percentage display
Battery internal
resistance display
Fast battery charging
CCA test of battery
Percentage of capacity
before and after
- Not charging or providing any power. The user can check the Remaining Battery Capacity (State of Charge)
50-400 Charging 12V STD batteries
50-400 Charging 12 V batteries below 10
50-400 Charging 12 V CAL batteries
50-200 Charging 24 V STD batteries
50-200 Charging 24 V batteries below 10
50-200 Charging 24 V CAL batteries
50-400 Charging 12 V lithium-ion (LiFePO4) batteries only
50-400 An advanced battery recovery mode for repairing old, idle, stratified or sulfated batteries
- Converting to a DC power supply for powering 12 V DC device or as a memory retainer when replacing a battery.
50-400 Delivering 20A for five (5) minutes to jump charge your battery
- Check vehicle's alternator output
- Check battery health (LEAD-ACID only), including SOC, SOH, CCA and internal resistance
WWW.BORMANNTOOLS.COM
Ordinary lead - Calcium
acid battery battery (CAL)
Low temperature Total capacity of
charging mode and AGM fully charged battery
battery type
Explanation
C (50 F) or 12V AGM battery
o o
C (50 F) or 24 V AGM battery (Green LED)
o o
Battery desulphation
Battery maintenance
Battery charging dynamic display
Battery remaining capacity display
Short circuit warning and battery
Power mode (13,5 10A)
(LiFEPO4)--12 V lithium
battery (4-Cell LiFePO4)
Total time required
for charger charging