Craftmade Builder Deluxe BLD42-LED-1 light Installation Manual
  1. Manuals
  2. Brands
  3. Craftmade Manuals
  4. Fan
  5. Builder Deluxe BLD42-LED-1
  6. Installation manual

Craftmade Builder Deluxe BLD42-LED-1 light Installation Manual

Hide thumbs Also See for Builder Deluxe BLD42-LED-1 light:
Table of Contents

Advertisement

Quick Links

Download this manual
Builder Deluxe
Installation Guide
For Models:
BLD42-LED-1 light
BLD52-LED-1 light
E192641
net weight of fan: 22.05 lb. (10 kg)
READ THESE INSTRUCTIONS
AND SAVE THEM FOR FUTURE USE

Table of Contents:

Wiring. pg. 6
Warranty. pg. 11
page 1
PRINTED IN CHINA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Builder Deluxe BLD42-LED-1 light and is the answer not in the manual?

Questions and answers

Related Manuals for Craftmade Builder Deluxe BLD42-LED-1 light

Summary of Contents for Craftmade Builder Deluxe BLD42-LED-1 light

  • Page 1: Table Of Contents

    READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Builder Deluxe Installation Guide For Models: BLD42-LED-1 light BLD52-LED-1 light Table of Contents: Safety Tips. pg. 2 Unpacking Your Fan. pg. 3 Parts Inventory. pg. 3 Installation Preparation. pg. 4 Hanging Bracket Installation. pg. 4 Fan Assembly.

  • Page 2: Safety Tips

    SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS.

  • Page 3: Unpacking Your Fan

    1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs.

  • Page 4: Installation Preparation

    3. Installation Preparation. blade edge To prevent personal injury and damage, ensure that the hanging location allows the blades a inches 7 feet (76 cm) clearance of 7 feet (2.13m) from the floor and (2.13m) 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 12ft.

  • Page 5: Fan Assembly. Pgs

    5. Fan Assembly. set screw Remove hanging ball from downrod provided by stop pin loosening set screw on hanging ball. Lower hanging ball and remove stop pin. Then, slide hanging ball off of downrod. [Refer to diagram 1.] hanging ball Loosen yoke set screws and nuts at top of motor housing.

  • Page 6: Wiring

    5. Fan Assembly. (cont.) With the hanging bracket secured to the outlet box and able to support the fan, you are now ready to hang your fan. Grab the fan firmly with two hands. Slide downrod through opening in hanging bracket and let hanging ball rest on the hanging bracket.

  • Page 7: Canopy Assembly

    7. Canopy Assembly. hanging bracket Locate 2 screws on underside of hanging bracket and remove screw closest to the open end of the hanging bracket. Partially loosen the other screw. Lift canopy to hanging bracket. Place rounded part of slotted hole in canopy over loosened screw in hanging bracket and push up.

  • Page 8: Light Kit Assembly (Optional). Pgs

    9. Light Kit Assembly (Optional). motor housing NOTE: If you do not wish to use the light kit, you may proceed to Section 10 on page 10 to complete installation. If you wish to use your fan WITH the switch housing light kit, remove 3 screws from switch housing and remove switch housing cap from switch housing.
  • Page 9 9. Light Kit Assembly (Optional). (cont.) motor Connect WHITE wire from switch housing housing to WHITE wire from light kit fitter. Connect reverse BLUE (or BLACK) wire from switch housing switch to BLACK wire from light kit fitter. When making the connections, use wire connectors that were previously removed.

  • Page 10: Testing Your Fan

    10. Testing Your Fan. It is recommended that you test fan motor housing before finalizing installation. Restore switch power from circuit box and light switch housing (if applicable). Test fan speeds with the pull chain located on the switch housing. Start at the OFF position (no blade movement).

  • Page 11: Troubleshooting

    Service at 1-800-486-4892 to arrange for return of fan. 1. Check wall switch to fan. Return fan, shipping prepaid, to Craftmade. We will repair 2. Verify that reverse switch is set completely in or ship you a replacement fan, and we will pay the return either direction.

This manual is also suitable for:

Builder deluxe bld52-led-1 light

Table of Contents