Operation; Maintenance - Hoover ONE PWR EVOLVE MAX User Manual

CHARGING
THE BATTERY
The charger included with your EVOLVE MAX
may differ from what is shown in this user
manual. Please reference the Accessories
section of this manual or contact us at
Hoover.com for more information of your
specific charger.
Ensure that the battery is fully charged
prior to use. This may take 3-4 hours to
fully charge. The battery will not ship fully
charged due to federal regulations.
1
Plug the charger into a power outlet.
2
Attach the battery pack to the charger by
aligning the ribs on the battery pack to the
grooves in the charger. Slide the battery pack
into the charger.
3
When charging, the lights on the battery will
illuminate to show the state of charge. If the
light on the charger flashes red, there is an error
with the battery or the charger. Try again or call
customer service for support. Once charge is
complete, lights on the battery will turn off.
4
To remove the battery pack from the charger,
press the latches and pull the battery away from
the charger.
TIP: During charging, the pack and ambient
temperature should be between 41°F to 86°F
(5°C and 30°C). The charger will sense if the
pack, or ambient temperature, is too cold or
too hot, and will return an error code (red
LED will be on) and not charge the pack. Use
battery only with charger listed. For use with
HOOVER® ONEPWR™ Lithium Ion Batteries.
ASSEMBLY
INSTRUCTIONS
HOW TO ASSEMBLE
Fully assemble product prior to use.
click
1
Connect the adapter into the body until it clicks
into place.
ASSEMBLY
INSTRUCTIONS
HOW TO ASSEMBLE (CONT'D)
click
2
Push the hand vacuum onto the adapter until it
clicks into place.
click
3
Attach the battery pack by aligning the ribs on
the battery pack to the grooves in the product.
Slide the battery pack into the product until it
clicks into place.

OPERATION

CAUTION:
Use extra care when cleaning
on stairs. To avoid personal injury or damage, and to
prevent the cleaner from falling, always place cleaner
at bottom of stairs or on floor. Do not place cleaner on
stairs or furniture, as it may result in injury or damage.
CAUTION:
Not to be used for grooming
a pet.
1
Press the ON/OFF button located on the shoulder.
The ON/OFF button and mode indicator lights will
illuminate when ON.
2
To change modes, press the Mode button on the
shoulder. The mode indicators will illuminate,
telling you which mode you are in.
• Evolve defaults to Hard Floor Mode. This mode
works well on all floor types and preserves
runtime.
• Use Carpet Mode for deep cleaning on carpets
with high suction.
• Use Brush Mode Off on delicate floor types. This
mode has high suction with the brush roll off.
3
Step on the nozzle of the product and pull back
handle to recline and begin cleaning.
USING THE ONEPWR™
DUST CHASER™
HAND VACUUM
1
To use the hand vacuum for above floor cleaning,
depress the hand vacuum release button and
pull the hand vacuum upwards off the adapter.
2
Remove the battery from the Evolve upright and
insert into the hand vacuum.
3
Press the ON/OFF button located on the top of
the hand vacuum.

MAINTENANCE

EMPTYING THE DIRT CUP
WARNING:
To reduce the risk of
injury from moving parts, remove the battery
before servicing.
1
Remove the battery pack.
2
Push down the latch on the dirt cup to
release. Rock the dirt cup backwards off
the body.
3
Hold the dirt cup over a trash bin and press the
dirt cup release button to empty.
LUBRICATION: The motor and brush roll
are equipped with bearings which contain
sufficient lubrication for their lifetime.
The addition of lubricant could cause
damage. Do not add lubricant to motor or
brush roll.
EMPTYING THE DIRT CUP (CONT'D)
4
To close, push the door until it locks back
into place.
5
Replace the dirt cup by aligning the bottom first
and then rocking it into place.
CLEANING THE FILTER AND
SEPARATOR
This product contains no serviceable parts.
If appliance is not working as it should, has
been dropped, damaged, left outdoors, or
dropped into water, call customer service at
1-800-406-2005 prior to continuing use.
1
Open the dirt cup lid to access the filter and
separator.
2
To clean the separator, lift to remove. Clean dirt
and debris by wiping the metal screen with a
cloth and then place back into the dirt cup.
3
Pull the filter away and tap over a trash can to
remove dirt. Rinse filter under warm water until
water comes out clear. Allow filter to air dry for
at least 24 hours until fully dry.
MOTOR PROTECTIONS: If the vacuum becomes
overloaded (which could occur when a large
obstruction is sucked up or when vacuuming
extremely thick carpet), the electronics are
designed to shut down the vacuum. If this happens,
the vacuum will automatically shut off. To reset the
vacuum, turn the unit to "O" or off, then turn on to
continue use. If it shuts down again there may be a
large obstruction in the vacuum. See Clearing Clogs
for the steps on clearing a clog from the air path.
TROUBLESHOOTING
FIND AVAILABLE REPLACEMENT PARTS AND ACCESSORIES AT HOOVER.COM.
IF APPLIANCE IS NOT WORKING AS IT SHOULD, HAS BEEN DROPPED, DAMAGED, LEFT OUTDOORS, OR
DROPPED INTO WATER, CALL CUSTOMER SERVICE AT 1-800-406-2005 PRIOR TO CONTINUING USE.
ACCESSORIES
GENUINE PARTS AND ACCESSORIES: We recommend using only with genuine HOOVER® replacement
bags (for Hoover bagged uprights), parts, and accessories. Damage caused by use with other than
genuine HOOVER® bags, parts, and accessories is not covered by and may void your warranty.
REMOVING AND REPLACING THE
BRUSH ROLL
WARNING:
Risk of personal injury -
Brush roll may suddenly restart. Turn power switch off
and remove battery before cleaning or servicing.
1
Remove the battery. Using your fingers or a coin,
push and turn the brush roll lock counterclock-
wise to release the brush roll.
2
Pull the brush roll out of the nozzle with the
pull tab.
3
To remove any threads or hair, slide the blade
of a pair of scissors into the groove of the brush
roll and cut along the groove. Clear any dirt/
debris from the end caps and inside the housing
of the nozzle.
4
Re-fit the brush roll into the nozzle and turn the
brush roll lock clockwise to lock.
THE BELT: This vacuum is equipped with
the fiber reinforced stretch belt, which
is designed for long life and doesn't need
changing.