Getting Started; Operation; Maintenance - Hoover FH14050 User Manual

GETTING STARTED

1
Remove the Solution Tank from the side of the
unit, then remove the cap.
2
Follow the formula ratio chart to add cleaning
formula in the Solution Tank.
3
Replace and tighten cap. Slide the tank back
into the unit. The tank is secured when you feel
a click.
4
Unwrap hose from unit. Select the preferred tool
and make sure it is attached securely.
NOTE: Read the directions on the Hoover® Carpet
Cleaning fluid prior to use.
CLEANING FLUID: SEE THE HOOVER SOLUTION
GUIDE insert or visit Hoover.com/cleaning-
solutions.
CAUTION:
Not to be used for grooming
a pet.
CAUTION:
Do not use this EXTRACTOR
on hard floors. Using this PRODUCT on hard
floors may scratch or damage your floor.
Before You Begin Cleaning
Use your Hoover upholstery and spot cleaner
only if upholstery fabric is marked with a "W"
(for "wet" clean) or "S/W" (for "solvent/dry"
or "wet" clean). Don't clean fabric marked "S"
("solvent/ dry" clean only).
Test for colorfastness in a small, hidden area.
Gently rub surface with a dampened white
cloth. Wait ten minutes and check for color
removal or bleed with a white paper towel.
NOTE: To prevent staining, use plastic or
aluminum foil to protect wood or metal surfaces
from possible water spray.
NOTE: To avoid damage to wood floors
underneath area rugs or carpet, place waterproof
material (e.g. plastic) underneath them before
cleaning.

OPERATION

CAUTION:
Do not clean over floor
electrical outlets. Water will drip from the tool
after use and may puddle. To avoid damage
to wood and laminate flooring and to avoid
potential slip hazard, after use (a) do not leave
the product on wood and laminate surfaces and
move to a hard surface and (b) place the unit
on an absorbent material (such as a towel) to
soak up drips.
1
Press the Red Power button on top of the unit to
turn ON.
2
Hold the tool about 5 inches over the spot or
stain. Spray a generous amount of cleaning
solution over the soiled area by pressing the
trigger behind the tool, and scrub the stain in a
back and forth motion.
TIP: For best results, pretreat tough stains before
using CleanSlate.
3
To lift the stain, suction up the dirt and cleaning
solution by applying downward pressure on the
front of the cleaning tool and pulling towards
you. Repeat as needed.
IMPORTANT: Empty the Recovery Tank when it
reaches the MAX fill line or you hear an audible
change. Ensure the tank is secured before
cleaning. Ensure the tank is secured before
cleaning.
For best results, pretreat stains with a HOOVER®
spot treatment (see HOOVER® Cleaning Solution
Guide) to help loosen and remove even the most
stubborn stains. Distribute a generous amount
of pretreat spray on spot, stain, or high traffic
area. Always follow specific directions found on
solution label. Wait 5–10 minutes before using
machine.
STORAGE: Wrap cord around the cord hooks for
convenient storage. Attach the plug end to the
cord. For fast cord release, simply turn the cord
wraps 180 degrees to the right or left.
LUBRICATION: The motor is equipped with
bearings which contain sufficient lubrication for
their lifetime. The addition of lubricant could
cause damage. Do not add lubricant to motor
bearings.
Tools and formula may vary by model.

MAINTENANCE

WARNING:
To reduce the risk of
personal injury - Unplug before cleaning or
servicing.
WARNING:
To reduce risk of fire
and electric shock due to internal component
damage, use only HOOVER® cleaning products
intended for use with the appliance, as noted.
This product contains no serviceable parts. If an
appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into
water, call customer service at 1.800.944.9200
prior to continuing use.
HOW TO CLEAN THE RECOVERY TANK
Press TANK RELEASE button, then lift lid off for
emptying and rinsing. Clean water will help
remove dirt & debris from the tank. Let air dry
before reinstalling.
HOW TO CLEAN TOOLS
1
Remove the tool from the hose. Rinse hand
tool under faucet. Remove the nozzle cover by
unlatching the clear tab.
2
Remove Insert and rinse under faucet.
HOW TO CLEAN HOSE
1
Remove the solution tank and fill with warm
water (max 140˚F (60˚C)) to the small area fill
line.
2
Remove any cleaning tool or attachment from the
hose, and attach the Hose Rinse Tool to the hose.
3
Ensure both the solution and recovery tanks are
secured on the unit. Turn the unit on and hold
the trigger for 30 seconds. The clean water will
rush through the hose, effectively cleaning and
removing odor causing bacteria left in the hose.
Repeat as needed. Let the unit run for 5–10
seconds before turning off.
4
Repeat process as needed and turn off the unit
when hose is fully clean. Empty the recovery
tank.
Thermal Protection
A thermal protector has been designed into your
cleaner to protect it from overheating. When
the thermal protector activates, the cleaner will
stop running.
If this happens, proceed as follows:
1. Turn cleaner OFF and unplug it from the
electrical outlet.
2. Empty Recovery Tank.
3. Inspect for any obstructions. Clear
obstructions if present.
4. When cleaner is unplugged and motor cools
for 30 minutes, the thermal protector will
deactivate and cleaning may continue.
If the thermal protector continues to activate
after following the above steps, your cleaner
needs servicing.