1. Foreword This operator’s manual for HIAB 160TM teaches you the right way to operate and maintain your crane. In this Operating manual are : - Important safety precautions and warnings - Important directions for use - An explanation of the arrangement of Operator’s manual - An explanation of the directions in the Operator’s manual...
2. The Operator’s Manual 2-1. Structure The Operator’s Manual for your crane consists of : - The Operator’s Manual applies to all HIAB stiff-boom cranes. It contains important safety precautions and warnings. The operator’s Manual also contains important general instructions for use.
2-2. Indications in the Operator’s Manual The following indications are used in the Operator’s Manual : ! TIP Tip to make work easy to carry out ! NOTE Extra information that can prevent problems CAUTION Hazard for the crane or crane components. Follow the instructions carefully WARNING Danger of injury to yourself or to bystanders, or...
2-3. Other indications Symbol for reference to illustration. Refers to an illustration. Symbol for reference to a component in an illustration. ① Refers to a component in an illustration. [Option] Indication for parts that are non-standard for the crane, but an option. !NOTE 1.
Never operate the crane when you are sick, tired out, under the influence of medicines, alcohol or other drugs 1. Take the delivery instructions from your HIAB dealer. Or be instructed by an experienced person from your own company.
Operation and Maintenance for your type of crane. All other maintenance work should be done in a HIAB service workshop. ▲ Deal yourself only with the faults described in the Operation and Maintenance for your type of crane. All other work to rectify faults may only be performed by personnel in a HIAB service workshop.
Page 12
With wind speed less than 13.3 m sec [approx. 29.7 mph] Consult the wind speed table, Appendix 1. ▲ DANGER Never use the crane in a high wind or storm. When wind speeds exceed 13.3 m/sec the crane will behave unpredictably. ▲...
3-4. Use and maximum load Use your crane only for loading and unloading cargo. ▲ DANGER Never lift people with the crane! People may only be lifted by cranes that are approved for it and equipped with a special platform for lifting people for work at heights.
3-5. Preparation for use ▲ DANGER Ensure that there are no unauthorized persons within the operating range of your crane! ! TIP Mark out the working range, with for example, cones. ! TIP Put on your vehicle warning lights. ▲ DANGER If a part of the crane comes in contact with an electricity line, you will certainly be electrocuted!
Page 15
Table 1 : Minimum distance between crane and overhead electricity lines Minimum distance Minimum distance Voltage(V) to an insulated to an uninsulated conductor conductor < 500 V 0.6 m 2.5 m 500 ~ 40,000 V > 40,000 V Voltages are found : Up to 500V : to houses 500 ~ 40,000 V : trams, trains...
Page 16
▲ Check that the ground is sufficiently firm. Check also that the ground is not undermined. Look out for sewers, cellars, excavations etc. The outrigger legs must not be able to sink in. ▲ DANGER On a slippery surface, for example because of frost : Place chocks under the wheels.
3-6. Use of the crane 3-6-1. Starting crane operation ▲ DANGER Ensure that you can see the outrigger legs when you are operating them. Operate the outrigger legs from the side of the legs concerned. Do not stand in front of the hydraulically- operated outrigger legs when you are operating them! ▲...
Page 18
▲ Do not lower the outrigger legs on the edge of an embankment, soft shoulder, slope etc. Lower the outrigger legs only on a flat surface. ▲ Slide the outrigger extension beams on both sides of the vehicle out completely. Then lower the outrigger legs for support. ▲...
3-6-2. Crane operation ▲ DANGER Keep checking that there is no unauthorized person within the operating reach of the crane! ▲ Make certain that you can always see the load! If your view of the loads is not adequate, have someone else give you signals.
Page 20
▲ WARNING Never push a load along the ground or the vehicle load space with the extension boom. This can cause damage, that will need expensive repairs, to the extension cylinder. ▲ Never use the extension boom as a jack. This could damage the slewing bearings and the connection between the crane column and the crane base.
▲ When loading the vehicle : Take the load off the outrigger legs by withdrawing them slightly. The outrigger legs must remain in light contact with the ground. ▲ Never operate the outrigger legs if the crane has a load. ▲...
Page 22
- Check that the locking works properly. - Disengage the P.T.O or power supply after the work. If you drive with the P.T.O or power supply engaged, this will cause serious damage to the P.T.O/gearbox combination. - Only after doing so should you drive away with the vehicle. ▲...
3-7. Driving with the crane ▲ DANGER Never drive the vehicle if there is a load suspended from the crane. ▲ Before you start to drive away : Check that you have no pump flow to the crane control valve. The PTO or power supply must be disengaged.
3-8. Use of lifting equipment ▲ DANGER Use only lifting accessories (winch, grapple, rotator) which are suitable for your crane. Get in touch with a HIAB dealer. ▲ Never attempt to install add-on lifting accessories yourself! Add-on lifting accessories may only be installed by an authorized HIAB dealer.
3-9. Use of demountable cranes ▲ DANGER Ensure that there are no unauthorized persons in the immediate vicinity of the crane. When putting the crane onto or off the vehicle people can suffer fatal crushing injuries! ▲ After setting up : Check that the crane is properly locked! ▲...
Only carry out the maintenance yourself that is prescribed in the Operation and Maintenance for your type of crane. All other maintenance work may only be carried out by HIAB service workshop! ▲ Do not do any welding work on the crane yourself! Welding work on the crane...
Page 27
Do not drill into the crane yourself. Drilling work on the crane may only be carried out by, or in close consultation with, a HIAB service workshop. ▲ Never try to reinstall the crane. Only a HIAB Dealer. may reinstall the crane.
Ensure that faults in the crane are rectified immediately! Follow the instructions for faults, in the Operation and Maintenance for your type of crane, exactly. Never rectified faults yourself that may only be rectified by a HIAB service workshop. ▲ DANGER If there is an oil leakage from the hydraulic system : Keep well away from an oil leak.
HIAB only provides a warranty if : - The instructions for maintenance and service have been followed, and - Original HIAB parts have been used, and - All the seals are still intact and - The maintenance schedule in your Crane logbook is filled in up-to-...
4. Technical description 4 - 1 Specification Description Specification Remarks Lifting Capacity 15.0 ton-m Max. working Radius 18.7 m 1.41 m - 6,500 kg 3.57 m - 3,170 kg 6.46 m - 1,740 kg Outreach - Lifting Capacity 11.24 m - 930 kg 14.88 m - 610 kg 18.70 m - 320 kg Max.
5. General description 5 - 1 Basic operation principle Hiab 160TM crane consists of mainly steel structures and hydraulic components. The required power source for crane operation comes, via the chassis’ power take off (PTO), from the hydraulic pump giving high pressure hydraulic oil.
5 - 3 Base The base is connected with the column structure by slewing bearing, which makes the crane rotate, and is mounted on the chassis frame with strong anchor bolts. 5 - 4 Column The column is of a closed welded box design and connected with the base.
5 - 6 Control Valve The Hiab 160TM stiff boom crane is equipped with two(2) control valves connected serially. One is for main controls of the crane (slewing, boom lifting, extension, winch), and the other is for the outrigger control (outrigger beam extending, outrigger jack cylinder).
5 - 7 Outrigger system The outrigger system consists of outrigger beam and legs which make the chassis stable when the crane is operating. The pilot check valves are installed on leg cylinders to prevent the leg cylinders to go down when driving and from hose failure when operating the crane.
5 - 8 Winch The winch consists of hydraulic motor, gearbox and winch drum. The winch is installed inside of the column structure. The mechanical brake is included in winch gearbox. 5 - 9 PTO & pump The PTO is mounted the gearbox of the chassis. This rotating power rotates the pump creating high hydraulic oil pressure.
5 - 10 Oil Tank The Hiab 160TM crane is equipped with an oil tank for separate mounting. The oil tank consists of tank body Itself, return filter, suction strainer, air breather, oil level gauge and drain plug which can be used for drainage of the water or some dirt accumulated in the tank bottom.
6. Operation 6 - 1 Before operating the crane Secure the hand brake of the chassis Check the oil level in the hydraulic oil tank Engage the PTO Extend the outrigger beam and down the outrigger legs firmly on the ground 6 - 2 Warming up when cold weather In cold weather, the viscosity of the operating oil could be very high.
6 - 3 Operating the outrigger The outrigger control valve levers are vertically installed on both sides of the crane. The first lever : front left side shift cylinder The second lever : front right side shift cylinder The third lever : front left jack cylinder The forth lever : front right jack cylinder The fifth lever : rear left side shift cylinder The sixth lever : rear right side shift cylinder...
6 - 4 Operation of crane Standard control valve 4 levers for operating crane. Before operating the crane, adjust the four (4) way valve lever to main control valve side. Please refer to below chart explaining the function of each lever. Operated components Pull Push...
Page 44
(note) 1) When boom raising / lowering, Move the lever slowly when loaded. Fast movement could cause tilting of the chassis or damages to the crane due to dynamic forces. 2) When hook raising / lowering, Do not lower more when load touches the ground. If you do so, the wire can get tangled.
6 - 5 Overwinding alarm Hiab 160TM is equipped with an overwinding alarm system. If the hook block is too near the boom tip, the alarm system will be activated. Before operating the crane, turn on the overwinding alarm switch.
6 - 6 After operation the crane (for driving) Retract the booms fully Rotate the boom at the driving position (front or rear side. Refer the sticker on slewing cover and column base plate) Retract the outrigger legs fully Retract the outrigger beam fully Lower the boom at lowest position Settle the hook with the safety rope on the chassis Operate (wind) the winch until the safe rope is tensioned...
7. Safety instruction when operating Press the clutch pedal fully and then engage or disengage the When cold weather, please warm up the operating oil for 10 - 15 minutes Operate the crane on even ground condition Before operating the hook, turn on the overwinding alarm switch Be careful not to touch the hook block on the ground, which could cause the wire to get tangled...
Page 48
Operate the crane smoothly If operated fast, the life cycle of the crane can be reduced and/or there can be some component troubles. At starting/finishing point, the movement should be reduced. Before operating the crane, make sure the outrigger system is extended and firmly settled on the ground.
8. Preventive service & Maintenance 8 - 1 Daily Inspection Where? What? Abnormal noise and/or heat? Power take off Engaging movement is smooth or not? Drive shaft Loosened or not? Oil level? Oil tank Leakage? Leakage? Greasing condition? Slewing system No loosened bolts? Abnormal noise? Shaft condition?
If there is some abnormal noise from the slewing system and/or the mounting parts when operating the crane or driving, please consult your Hiab dealer or service center. That kind of noise could come from loosened condition of the mounting bolts. At least, mounting bolts of slewing bearing located inside of the column should be checked every 2 years.
Page 51
Adjusting twisted wire rope Wire rope tends to turn in the untwisting direction under tension. When the hook carries two or more wire rope slings, they can easily turn, especially when they are still new. Wire rope becomes steady with use. The wire rope adjustment procedure is: Extend the boom fully Set the boom to an angle of about 65 deg...
Page 52
Turn the wire socket opposite to the wire rope twisting direction, except in the case of 3-rope sling in which case the wire socket should be turned in the same direction. How to look after the winch rope The winch rope must be regularly cleaned and greased for maximum life, bearing in mind that the rope is subject to wear and to heavy stresses which set a limit of it’s service life.
Page 53
The winch rope must be changed as soon as any of the following occur; When 5 % of wires in any length of ten rope diameters are broken, worn or corroded When visible changes occur in the diameter(more than 7 %) of the winch in comparison with the normal stretching and...
The oil filter insert should therefore be changed for the first time after 50 running hours and from then on every 500 running hours, subject to a minimum of at least two changes a year. For best results, always fit a genuine Hiab insert.
Page 55
Replacing the return oil filter insert Clean the immediate surroundings of the return filter. Turn the cover ① to free it while pressing on it Pull the return filter out of the oil tank Remove the filter insert ③ Insert a new filter insert Fit new sealing rings ②, ④...
8 - 5 Inspection points when operating Is there any leakage? Does the crane operate smoothly? Is there any abnormal noise? How about the oil temperature? If the oil temperature is higher than 75 deg C, then stop the crane operation 8 - 6 Inspection after operation Clean &...
Check oil levels and lubrication in accordance with the lubrication chart in the manual Put the crane through test-running and test-loading, and listen for any suspicious noises 8 - 8 Inspection & maintenance after 6 months in operation Clean the crane Check pressure settings and lead seals Check for oil leakage Check and advance screwed connections...
9. Lubrication 9 - 1 Hydraulic oil changing Check the level in the tank every day. The oil level must be visible in the sight glass. At this check, the crane must be in parked position. Top up with hydraulic oil if necessary. Hydraulic becomes contaminated...
Page 59
When changing the oil, change the filters at the same time. The hydraulic system and the hydraulic fluid are matched in respect of lubricating performance, effect on the seals and other materials, and non-inflammability. For this reason, do not mix different types of hydraulic fluid, such as mineral oils, synthetic fluids and water-based fluids, and never adulterate your hydraulic fluid with diesel oil or alcohol-based products.
9 - 2 Lubrication chart Good performance and trouble-free operation of the crane depends a great deal on service. For this reason, always follow the recommendation on the lubrication chart. Pos Interval Point Rec. Lubricant Q’ty Boom pads Derrick cylinder shaft Shell Alvania EP grease 2 Every day Boom + Column shaft...
10. Fault Tracing Fault tracing is mainly based on organized routine for finding a certain functional disorder, its reason and how to correct it. The following charts contain some faults which may arise during operation, how they appear and which steps to be taken. Most important, however, is that the crane is checked and necessary adjustments made before the crane is taken into operation.
Page 62
Dirt in counter balance Clean and/or change valve or damage in seal Internal leakage Repair Boom do not extend cylinder Sequence valve fault Clean/repair Lack of oil Top up the oil Dirties in counter balance Boom do not retract Clean and/or change valve or damage in seal Internal leakage...
Appendix 1 : Wind speeds Wind speed averaged over 10 min. at Wind a height of 10 m characteristics force Above flat ground Wind type Calm, smoke rises vertically or nearly vertically 0.0 ~ 0.2 Calm Wind direction recognizable from smoke plumes, 0.3 ~ 1.5 Slight breeze wind begins to be noticeable on the face;...
Appendix 2 : Signals when using a crane If you cannot see the load properly, someone else should give you signals. This appendix gives a number of the standard signals. !NOTE Have the person giving the signal stand facing you as far as possible. The speed of the hand and arm movements indicate at what speed the crane movement should be made.
Page 65
Very short movement Place the hands a very short distance apart, with the palms facing each other. The hands may be held either horizontally or vertically. The next movement may be : Lift, lower, move the lifting gear, change the reach, or turn. Change the reach Indicate this by means of the hand, if necessary providing a precise indication with...
Page 66
Close the grapple Move both hands close together. Lift the open grapple a little Extend both arms at shoulder height, with the palms facing upwards. Make vertical movements with both arms outstretched. Keep the grapple in position briefly Raise the hand slightly drooping, with the fist clenched.
Page 67
160TM SPARE PARTS LIST Cargotec Korea Ltd...
Page 68
Instruction This spare parts catalogue has several main divisions each embracing a main component group, where you can find easily the necessary part. Each drawing is followed by the corresponding written material Parts shown in the drawings are numbers by position starting from 1, drawings are numbered as;...
Page 69
주요 부분 지시도 HIAB160TM-6 0 : 1 MAIN SUBDIVISIONS 2015. 04. HIAB160TM-6 - 0 : 1 HIAB160TM-6 - 10 : 0 주요 부품 지시도 3단 신축 실린더 MAIN SUBDIVISIONS 3rd EXTENSION CYLINDER HIAB160TM-6 - 1-1 : 1 HIAB160TM-6 - 10 : 0 크레인...
Page 70
주요 부분 지시도 HIAB160TM-6 0 : 1 MAIN SUBDIVISIONS 2015. 04. HIAB160TM-6 - 21 : 0 HIAB160TM-6 - 31-2 : 1 주 제어 밸브 31-2 전기 배선도 - 무선과권 MAIN CONTROL VALVE ELECTRIC WIRING DIAGRAM - TRANSMITTER HIAB160TM-6 - 22 : 1 HIAB160TM-6 - 32 : 1 아우트리거...
Page 71
크레인 총 결합체 HIAB160TM-6 1-1 : 1 HIAB160TM TOTAL ASS'Y 2015. 04. SPARE PARTS LIST...
Page 72
크레인 총 결합체 HIAB160TM-6 1-1 : 1 HIAB160TM TOTAL ASS'Y 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks A00-0394...
Page 73
크레인 총 결합체 - 무선과권 HIAB160TM-6 1-2 : 1 HIAB160TM TOTAL ASS'Y - TRANSMITTER 2015. 04. SPARE PARTS LIST...
Page 74
크레인 총 결합체 - 무선과권 HIAB160TM-6 1-2 : 1 HIAB160TM TOTAL ASS'Y - TRANSMITTER 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No.
Page 75
베이스 및 칼럼 결합체 HIAB160TM-6 2 : 1 BASE & COLUMN ASS'Y 2015. 04. SPARE PARTS LIST...
Page 76
베이스 및 칼럼 결합체 HIAB160TM-6 2 : 1 BASE & COLUMN ASS'Y 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks...
Page 77
베이스 및 칼럼 결합체 HIAB160TM-6 2 : 1 BASE & COLUMN ASS'Y 2015. 04. SPARE PARTS LIST...
Page 78
베이스 및 칼럼 결합체 HIAB160TM-6 2 : 1 BASE & COLUMN ASS'Y 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks...
Page 79
베이스 및 칼럼 결합체 HIAB160TM-6 2 : 1 BASE & COLUMN ASS'Y 2015. 04. SPARE PARTS LIST...
Page 80
베이스 및 칼럼 결합체 HIAB160TM-6 2 : 1 BASE & COLUMN ASS'Y 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks...
Page 81
베이스 배관도 HIAB160TM-6 3 : 1 BASE HOSE & PIPING 2015. 04. SPARE PARTS LIST...
Page 82
베이스 배관도 HIAB160TM-6 3 : 1 BASE HOSE & PIPING 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks A02-3403...
Page 83
베이스 배관도 HIAB160TM-6 3 : 1 BASE HOSE & PIPING 2015. 04. SPARE PARTS LIST...
Page 84
베이스 배관도 HIAB160TM-6 3 : 1 BASE HOSE & PIPING 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks 7172333...
Page 85
베이스 배관도 HIAB160TM-6 3 : 1 BASE HOSE & PIPING 2015. 04. SPARE PARTS LIST...
Page 86
베이스 배관도 HIAB160TM-6 3 : 1 BASE HOSE & PIPING 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks H01-6622...
Page 87
아우트리거 제어 장치 HIAB160TM-6 4 : 1 OUTRIGGER CONTROL SYSTEM 2015. 04. SPARE PARTS LIST...
Page 88
아우트리거 제어 장치 HIAB160TM-6 4 : 1 OUTRIGGER CONTROL SYSTEM 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks A02-3392...
Page 89
아우트리거 제어 장치 HIAB160TM-6 4 : 1 OUTRIGGER CONTROL SYSTEM 2015. 04. SPARE PARTS LIST...
Page 90
아우트리거 제어 장치 HIAB160TM-6 4 : 1 OUTRIGGER CONTROL SYSTEM 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks 3112106...
Page 91
아우트리거 제어 밸브 HIAB160TM-6 5 : 1 OUTRIGGER CONTROL VALVE 2015. 04. SPARE PARTS LIST...
Page 92
아우트리거 제어 밸브 HIAB160TM-6 5 : 1 OUTRIGGER CONTROL VALVE 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks H02-1211...
Page 93
아우트리거 제어 밸브 HIAB160TM-6 5 : 1 OUTRIGGER CONTROL VALVE 2015. 04. SPARE PARTS LIST...
Page 94
아우트리거 제어 밸브 HIAB160TM-6 5 : 1 OUTRIGGER CONTROL VALVE 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks H02-1148...
Page 95
붐 시스템 HIAB160TM-6 6 : 1 BOOM SYSTEM 2015. 04. SPARE PARTS LIST...
Page 96
붐 시스템 HIAB160TM-6 6 : 1 BOOM SYSTEM 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks A01-4222 M01-1078 붐...
Page 97
붐 시스템 HIAB160TM-6 6 : 1 BOOM SYSTEM 2015. 04. SPARE PARTS LIST...
Page 98
붐 시스템 HIAB160TM-6 6 : 1 BOOM SYSTEM 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks BOO-0007 Φ25×42L BOO-0023...
Page 99
붐 시스템 HIAB160TM-6 6 : 1 BOOM SYSTEM 2015. 04. SPARE PARTS LIST...
Page 100
붐 시스템 HIAB160TM-6 6 : 1 BOOM SYSTEM 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks BOO-0073 M20×220 BOO-5056...
Page 101
붐 시스템 HIAB160TM-6 6 : 1 BOOM SYSTEM 2015. 04. SPARE PARTS LIST...
Page 102
붐 시스템 HIAB160TM-6 6 : 1 BOOM SYSTEM 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks BOO-0062 t=2.3 2110906...
Page 103
붐 시스템 HIAB160TM-6 6 : 1 BOOM SYSTEM 2015. 04. SPARE PARTS LIST...
Page 104
붐 시스템 HIAB160TM-6 6 : 1 BOOM SYSTEM 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks 3112181 NA18 M01-1079...
Page 106
신축 실린더 결합체 HIAB160TM-6 7 : 0 EXTENSION CYLINDER ASS'Y 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks H01-4128...
Page 108
1단 신축 실린더 HIAB160TM-6 8 : 0 1st EXTENSION CYLINDER 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks H01-4129...
Page 110
1단 신축 실린더 HIAB160TM-6 8 : 0 1st EXTENSION CYLINDER 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks SS33T10S1...
Page 112
1단 신축 실린더 HIAB160TM-6 8 : 0 1st EXTENSION CYLINDER 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks NI-300...
Page 114
2단 신축 실린더 HIAB160TM-6 9 : 0 2nd EXTENSION CYLINDER 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks H01-4130...
Page 116
2단 신축 실린더 HIAB160TM-6 9 : 0 2nd EXTENSION CYLINDER 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks SH17T2040...
Page 118
2단 신축 실린더 HIAB160TM-6 9 : 0 2nd EXTENSION CYLINDER 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks 1BG 60...
Page 120
3단 신축 실린더 HIAB160TM-6 10 : 0 3rd EXTENSION CYLINDER 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks H01-4131...
Page 122
3단 신축 실린더 HIAB160TM-6 10 : 0 3rd EXTENSION CYLINDER 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks M6×P1.0×15L...
Page 124
쉬브 결합체 HIAB160TM-6 11 : 0 SHEAVE ASS'Y 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks A02-2565 S01-1596 쉬브...
Page 125
윈치 장치 HIAB160TM-6 12 : 1 WINCH SYSTEM 2015. 04. SPARE PARTS LIST...
Page 126
윈치 장치 HIAB160TM-6 12 : 1 WINCH SYSTEM 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks WC-2001 2110926 BA8×30...
Page 128
윈치 감속기 결합체 HIAB160TM-6 13 : 0 WINCH REDUCER ASS'Y 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks H02-0296...
Page 130
윈치 감속기 결합체 HIAB160TM-6 13 : 0 WINCH REDUCER ASS'Y 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks PF1/2...
Page 132
선회 감속기 HIAB160TM-6 14 : 0 SLEWING REDUCER 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks BC1-0003 07-04-2007 선회...
Page 134
선회 감속기 HIAB160TM-6 14 : 0 SLEWING REDUCER 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks BC1-0003-4 AN09 BC1-0003-13...
Page 136
선회 감속기 HIAB160TM-6 14 : 0 SLEWING REDUCER 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks 3612101 WS10 스프링...
Page 137
선회 모터 HIAB160TM-6 15 : 0 SLEWING MOTOR 2013. 05. SPARE PARTS LIST...
Page 138
선회 모터 HIAB160TM-6 15 : 0 SLEWING MOTOR 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks H02-0200 OMP100C 151-1128...
Page 140
카운터 발란스 밸브 HIAB160TM-6 16 : 0 COUNTER BALANCE VALVE (D) 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks...
Page 142
데릭 실린더 HIAB160TM-6 17 : 0 DERRICK CYLINDER 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks H01-2170 HN52D0000 6012412...
Page 144
로타리 조인트 결합체 HIAB160TM-6 18 : 1 ROTARY JOINT ASS'Y 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks A02-1740...
Page 145
운전석 결합체 HIAB160TM-6 19 : 1 TOP SEAT ASS'Y 2015. 04. SPARE PARTS LIST...
Page 146
운전석 결합체 HIAB160TM-6 19 : 1 TOP SEAT ASS'Y 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks A01-0538 2112137...
Page 147
운전석 결합체 HIAB160TM-6 19 : 1 TOP SEAT ASS'Y 2015. 04. SPARE PARTS LIST...
Page 148
운전석 결합체 HIAB160TM-6 19 : 1 TOP SEAT ASS'Y 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks 998 9676 4510211...
Page 149
운전석 배관도 HIAB160TM-6 20 : 1 TOP SEAT HOSES 2015. 04. SPARE PARTS LIST...
Page 150
운전석 배관도 HIAB160TM-6 20 : 1 TOP SEAT HOSES 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks A01-0794 H01-0901...
Page 151
주 제어 밸브 HIAB160TM-6 21 : 0 MAIN CONTROL VALVE 2013. 05. SPARE PARTS LIST...
Page 152
주 제어 밸브 HIAB160TM-6 21 : 0 MAIN CONTROL VALVE 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks H02-0290...
Page 153
주 제어 밸브 HIAB160TM-6 21 : 0 MAIN CONTROL VALVE 2013. 05. SPARE PARTS LIST...
Page 154
주 제어 밸브 HIAB160TM-6 21 : 0 MAIN CONTROL VALVE 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks 스풀...
Page 155
주 제어 밸브 HIAB160TM-6 21 : 0 MAIN CONTROL VALVE 2013. 05. SPARE PARTS LIST...
Page 156
주 제어 밸브 HIAB160TM-6 21 : 0 MAIN CONTROL VALVE 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks 2330-260588...
Page 158
아우트리거 결합체 HIAB160TM-6 22 : 1 OUTRIGGER ASS'Y 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks OR1-3001 6010141 1B P12...
Page 160
아우트리거 결합체 HIAB160TM-6 22 : 1 OUTRIGGER ASS'Y 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks N01-0932 Φ25 핀...
Page 162
아우트리거 실린더 HIAB160TM-6 23 : 1 OUTRIGGER CYLINDER 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks H01-2061 HN03FJ000-03 Φ55×Φ60×15W...
Page 163
사이드 쉬프트 실린더 HIAB160TM-6 24 : 0 SIDE SHIFT CYLINDER 2013. 05. SPARE PARTS LIST...
Page 164
사이드 쉬프트 실린더 HIAB160TM-6 24 : 0 SIDE SHIFT CYLINDER 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks H01-1431...
Page 165
파일로트 체크 밸브 (D) HIAB160TM-6 25 : 0 PILOT CHECK VALVE (D) 2013. 05. SPARE PARTS LIST...
Page 166
파일로트 체크 밸브 (D) HIAB160TM-6 25 : 0 PILOT CHECK VALVE (D) 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks...
Page 167
후방 아우트리거 시스템 (옵션) HIAB160TM-6 26 : 1 REAR OUTRIGGER SYSTEM (OPTION) 2015. 04. SPARE PARTS LIST...
Page 168
후방 아우트리거 시스템 (옵션) HIAB160TM-6 26 : 1 REAR OUTRIGGER SYSTEM (OPTION) 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks...
Page 169
후방 아우트리거 시스템 (옵션) HIAB160TM-6 26 : 1 REAR OUTRIGGER SYSTEM (OPTION) 2015. 04. SPARE PARTS LIST...
Page 170
후방 아우트리거 시스템 (옵션) HIAB160TM-6 26 : 1 REAR OUTRIGGER SYSTEM (OPTION) 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks...
Page 172
후방 아우트리거 실린더 (옵션) HIAB160TM-6 27 : 0 REAR OUTRIGGER CYLINDER (OPTION) 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks...
Page 173
후방 사이드 쉬프트 실린더 (옵션) HIAB160TM-6 28 : 0 REAR SIDE SHIFT CYLINDER (OPTION) 2013. 05. SPARE PARTS LIST...
Page 174
후방 사이드 쉬프트 실린더 (옵션) HIAB160TM-6 28 : 0 REAR SIDE SHIFT CYLINDER (OPTION) 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No.
Page 175
파일럿 체크 밸브 (옵션) HIAB160TM-6 29 : 1 PILOT CHECK VALVE (D) (OPTION) 2015. 04. SPARE PARTS LIST...
Page 176
파일럿 체크 밸브 (옵션) HIAB160TM-6 29 : 1 PILOT CHECK VALVE (D) (OPTION) 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No.
Page 180
스티커 배열 HIAB160TM-6 30 : 0 STICKER ARRANGEMENT 2013. 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks P01-0266 라인...
Page 181
전기 배선도 HIAB160TM-6 31-1 : 1 ELECTRIC WIRING DIAGRAM 2015. 04. SPARE PARTS LIST...
Page 182
전기 배선도 HIAB160TM-6 31-1 : 1 ELECTRIC WIRING DIAGRAM 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks E00-0116 전기배선도...
Page 183
전기 배선도 - 무선과권 HIAB160TM-6 31-2 : 1 ELECTRIC WIRING DIAGRAM - TRANSMITTER 2015. 04. SPARE PARTS LIST...
Page 184
전기 배선도 - 무선과권 HIAB160TM-6 31-2 : 1 ELECTRIC WIRING DIAGRAM - TRANSMITTER 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No.
Page 185
전기 와이어 결합체 HIAB160TM-6 32 : 1 ELECTRIC WIRE ASS'Y 2015. 04. SPARE PARTS LIST...
Page 186
전기 와이어 결합체 HIAB160TM-6 32 : 1 ELECTRIC WIRE ASS'Y 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks E01-0924...
Page 187
전기 결합체 HIAB160TM-6 33-1 : 1 ELECTRIC ASS'Y 2015. 04. SPARE PARTS LIST...
Page 188
전기 결합체 HIAB160TM-6 33-1 : 1 ELECTRIC ASS'Y 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks E01-1181 E01-0918 1.5SQ...
Page 189
전기 결합체 - 무선과권 HIAB160TM-6 33-2 : 1 ELECTRIC ASS'Y - TRANSMITTER 2015. 04. SPARE PARTS LIST...
Page 190
전기 결합체 - 무선과권 HIAB160TM-6 33-2 : 1 ELECTRIC ASS'Y - TRANSMITTER 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks...
Page 191
오일 탱크 HIAB160TM-6 34 : 0 OIL TANK 2013 . 05. SPARE PARTS LIST...
Page 192
오일 탱크 HIAB160TM-6 34 : 0 OIL TANK 2013 . 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks A02-0950 S01-0741...
Page 193
오일 탱크 HIAB160TM-6 34 : 0 OIL TANK 2013 . 05. SPARE PARTS LIST...
Page 194
오일 탱크 HIAB160TM-6 34 : 0 OIL TANK 2013 . 05. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks 3511081 평...
Page 196
리턴 필터 HIAB160TM-6 35 : 0 FILTER, RETURN 2015. 04. 부 품 번 호 품 명 비 고 부 품 번 호 품 명 비 고 번호 수량 번호 수량 Part No. Description Q`ty Remarks Part No. Description Q`ty Remarks H01-1287 리턴...
Page 197
Cheongju Chungbuk 363-893 South Korea. No parts of this publication may be reproduced or copied Tel : +82 43 231 6300 in any form or by any means without written permission Fax : +82 43 231 6200 of Cargotec Korea Ltd. www.hiab.com...
Need help?
Do you have a question about the 160TM and is the answer not in the manual?
Questions and answers