DAEWOO ELECTRONICS DSL-19M1WCD Service Manual page 15

GNDS 167 AG
A1P 168 AI
GNDS 169 AG
B1P 170 AI
GNDS 171 AG
C1P 172 AI
AVDD_A 173 AP
AN 174 AI
AGND 175 AG
SV2P 176 AI
GNDS 177 AG
A2P 178 AI
GNDS 179 AG
B2P 180 AI
GNDS 181 AG
C2P 182 AI
AVDD_B 183 AP
BN 184 AI
AGND 185 AG
SV3P 186 AI
VDD18_AB 158 AP
GNDS 187 AG
A3P 188 AI
GNDS 189 AG
B3P 190 AI
GNDS 191 AG
C3P 192 AI
AVDD_C 193 AP
CN 194 AI
AGND 195 AG
SV4P 196 AI
GNDS 197 AG
A4P 198 AI
GNDS 199 AG
B4P 200 AI
GNDS 201 AG
C4P 202 AI
AVDD_SC 203 AP
Analog Ground. Must be directly connected to the analog system ground plane on board.
Positive analog input 'A' for channel 1.
The input has to be AC coupled using a series 20 Ohm resistor and 0.1uF Capacitor network.
Analog Ground. Must be directly connected to the analog system ground plane on board.
Positive analog input 'B' for channel 1.
The input has to be AC coupled using a series 20 Ohm resistor and 0.1uF Capacitor network.
Analog Ground. Must be directly connected to the analog system ground plane on board.
Positive analog input 'C' for channel 1.
The input has to be AC coupled using a series 20 Ohm resistor and 0.1uF Capacitor network.
Analog Power (3.3V) for ADC of Channel-A. Must be bypassed with 0.1uF capacitor to the analog system
ground plane.
Negative analog input 'A' for channels 1 through 4.
This acts as the return Path for the Sources connected to Channel-A Inputs. This has to be AC coupled
using a series 20 Ohm resistor and 0.1uF Capacitor network to Analog Ground Plane on board.
Analog Ground. Must be directly connected to the analog system ground plane on board.
Positive analog sync input for channel 2.
The input has to be AC coupled using a series 20 Ohm resistor and 0.1uF Capacitor network.
Analog Ground. Must be directly connected to the analog system ground plane on board.
Positive analog input 'A' for channel 2.
The input has to be AC coupled using a series 20 Ohm resistor and 0.1uF Capacitor network.
Analog Ground. Must be directly connected to the analog system ground plane on board.
Positive analog input 'B' for channel 2.
The input has to be AC coupled using a series 20 Ohm resistor and 0.1uF Capacitor network.
Analog Ground. Must be directly connected to the analog system ground plane on board.
Positive analog input 'C' for channel 2.
The input has to be AC coupled using a series 20 Ohm resistor and 0.1uF Capacitor network.
Analog Power (3.3V) for ADC of Channel-B. Must be bypassed with 0.1uF capacitor to the analog system
ground plane.
Negative analog input 'B' for channels 1 through 4.
This acts as the return Path for the Sources connected to Channel-B Inputs. This has to be AC coupled
using a series 20 Ohm resistor and 0.1uF Capacitor network to Analog Ground Plane on board.
Analog Ground. Must be directly connected to the analog system ground plane on board.
Positive analog sync input for channel 3.
The input has to be AC coupled using a series 20 Ohm resistor and 0.1uF Capacitor network.
Analog Power (1.8V) for A & B Channels. Must be bypassed with 0.1uF capacitor to the analog system
ground plane.
Analog Ground. Must be directly connected to the analog system ground plane on board.
Positive analog input 'A' for channel 3.
The input has to be AC coupled using a series 20 Ohm resistor and 0.1uF Capacitor network.
Analog Ground. Must be directly connected to the analog system ground plane on board.
Positive analog input 'B' for channel 3.
The input has to be AC coupled using a series 20 Ohm resistor and 0.1uF Capacitor network.
Analog Ground. Must be directly connected to the analog system ground plane on board.
Positive analog input 'C' for channel 3.
The input has to be AC coupled using a series 20 Ohm resistor and 0.1uF Capacitor network.
Analog Power (3.3V) for ADC of Channel-C. Must be bypassed with 0.1uF capacitor to the analog system
ground plane.
Negative analog input 'C' for channels 1 through 4.
This acts as the return Path for the Sources connected to Channel-C Inputs. This has to be AC coupled
using a series 20 Ohm resistor and 0.1uF Capacitor network to Analog Ground Plane on board.
Analog Ground. Must be directly connected to the analog system ground plane on board.
Positive analog sync input for channel 4.
The input has to be AC coupled using a series 20 Ohm resistor and 0.1uF Capacitor network.
Analog Ground. Must be directly connected to the analog system ground plane on board.
Positive analog input 'A' for channel 4.
The input has to be AC coupled using a series 20 Ohm resistor and 0.1uF Capacitor network.
Analog Ground. Must be directly connected to the analog system ground plane on board.
Positive analog input 'B' for channel 4.
The input has to be AC coupled using a series 20 Ohm resistor and 0.1uF Capacitor network.
Analog Ground. Must be directly connected to the analog system ground plane on board.
Positive analog input 'C' for channel 4.
The input has to be AC coupled using a series 20 Ohm resistor and 0.1uF Capacitor network.
Analog Power (3.3V) for ADC of SYNC Channel. Must be bypassed with 0.1uF capacitor to the analog
system ground plane.