LTD-61915E SERVICE MANUAL CONTENT Brief Introduction Of The LTD-61915E PART 1: Schematic Diagram ◆ Printed Circuit ◆ Exploded view PART 2: Key Ics And Assemblies PART 3: Detailed Circuit PART 4: Main Board ◆ DVD Board ◆ HI-voltage Board ◆ Parts List PART 5: Debug Procedure...
Part 1 Brief Introduction Of The LTD-61915E Schematic Diagram 12V IN POWER SUPPLY Panel AV OUT Composite 19” TFT LCD 12V 5V LVDS 3.3V 1.8V PC IN FLI8125 AT49BV040B Hsync Vsync 74LVC125 Decoder FLASH & AV IN Scaler Composite SVIDEO IN Composite FSAV330 SCART IN...
Part 3 Key ICs And Assemblies On Main Board On DVD board Serial No Position Type Serial no Position Type FSAV330 BA033T L7808C-V LM1117 AT49BV040B MT1389HD FLI8125 BA5954 FDS9435A BA6208F AP1510 HY57V641620HGT AT24C32A MX29LV160BT AP1513S AT24C16 CD4052 NJM4558 MSP3415G WM8714 TDA1517P 3U5 3U6 3U7 PESD5VOL4U...
Page 12
ICS ON MAIN BOARD 1. FSAV330 Low On Resistance Quad SPDT Wide Bandwidth Video Switch...
Page 13
2. FLI8125 The FLI8125 is a cost-effective, highly-integrated, mixed signal solution for TV and Digital Video applications. It incorporates a multi-standard video decoder, high-speed triple 8-bit Analog-to-Digital Converter(ADC),and front end switching. An integrated VBI Slicer adds Closed Captioning(CC) and Teletext service support, and the built-in microprocessor enables full system control without external devices.
Page 14
·PInput ·Pin List I/O Legend: A = Analog, I = Input, O = Output, P = Power, G= Ground Table 1: Analog Input Port Pin Name Description VDD18_A Analog Power (1.8V) for A & B Channels. Must be bypassed with 0.1uF capacitor to the analog system ground plane.
Page 15
GNDS Analog Ground. Must be directly connected to the analog system ground plane on board. Positive analog input ‘A’ for channel 1. The input has to be AC coupled using a series 20 Ohm resistor and 0.1uF Capacitor network. GNDS Analog Ground.
Page 16
Negative analog sync input for channels 1 through 4. This acts as the return Path for the Sources connected to SV Channel Inputs. This has to be AC coupled using a series 20 Ohm resistor and 0.1uF Capacitor network to Analog Ground Plane on board. VO_GND Analog Ground.
Page 17
Pin Name Description VID_DATA_IN_8 Input Pr / Pb Data in case of 16 Bit Video Input (CCIR601) of Video Input – 1 VID_DATA_IN_9 OR Input Green Data in case of 24 Bit Video Input VID_DATA_IN_10 VID_DATA_IN_11 VID_DATA_IN_12 VID_DATA_IN_13 VID_DATA_IN_14 VID_DATA_IN_15 VID_DATA_IN_16 Input Blue Data in case of 24 Bit Video Input VID_DATA_IN_17...
Page 18
Pin Name Description GPIO14/PWM3/ This Pin can be programmed to give out Pulse Width Modulated Output Pulses for external use. SCART16 Or it can be programmed to sense the Fast Blank Input signal from a SCART I/P source. When not used, this pin is available as General Purpose Input/output Port. This Pin provides the Output Data in case of Boundary Scan Mode.
Page 19
Table 7: TTL Display Interface Pin Name Description For 8-bit panels For 6-bit panels PBIAS Panel Bias Control (backlight enable) [Tri-state output, 5V- tolerant] PPWR Panel Power Control [Tri-state output, 5V- tolerant] AVDD_LV_33 Digital Power for TTL Block. Connect to digital 3.3V supply. Reserved.
Page 20
Blue channel bit 6 (Odd) Blue channel bit 4 (Odd) PD46 PD47 Blue channel bit 7 (Odd) Blue channel bit 5 (Odd) Note: In case of 24 Bit TTL Panels the RGB Odd Channel Outputs will not be used. In that case they can be made available for other purposes as Address &...
Page 21
3. FDS9435A Single P-Channel Enhancement Mode Field Effect Transistor SO-8 P-Channel enhancement mode power field effect transistors are produced using Fairchild's proprietary, high cell density, DMOS technology. This very high density process is especially tailored to minimize on-state resistance and provide superior switching performance.
Page 22
4. AT24C32A 2-Wire Serial EEPROM 32K (4096 x 8)
Page 29
8. CD4052B The CD4052B is a differential 4-Channel multiplexer having two binary control inputs, A and B, and an inhibit input. The two binary signals select 1 of 4 pairs of channels to be turned on and connect the analog inputs to the outputs. PInputs...
Page 30
ICS ON DVD BOARD 1. BA033T Low saturation voltage type 3-pin regulator...
Page 31
2. LM1117 (See Page 22) 3. MT1389HD Abbr. : SR : Slew Rate PU : Pull Up PD : Pull Down SMT : Schmitt Trigger 2MA~16MA : Output buffer driving strength. Main Alt. Type Description RF Interface ( 26 ) RFGND18 Ground Analog ground...
Page 32
ADC Power ( 2 ) ADCVDD3 Power Analog 3.3V Power for ADC ADCVSS Ground Analog ground for ADC VPLL (3) VPLLVSS Ground Analog ground for VPLL CAPPAD Analog Input VPLL External Capacitance connection VPLLVDD3 Power Analog 3.3V Power for VPLL Reference Voltage ( 3 ) V2REFO Analog output...
Page 33
RF Data PLL Interface ( 9 ) Main Alt. Type Description JITFO Analog output The output terminal of RF jitter meter. JITFN Analog Input The input terminal of RF jitter meter. PLLVSS Ground Ground pin for data PLL and related analog circuitry. IDACEXLP Analog output Data PLL DAC Low-pass filter...
Page 34
Input HIGHA0 2~16MA, SR Microcontroller address 8 Input HIGHA1 2~16MA, SR Microcontroller address 9 Input HIGHA2 2~16MA, SR Microcontroller address 10 Input HIGHA3 2~16MA, SR Microcontroller address 11 Input HIGHA4 2~16MA, SR Microcontroller address 12 Input HIGHA5 2~16MA, SR Microcontroller address 13 Input HIGHA6 2~16MA, SR...
Page 35
Input IOA0 2~16MA, SR Microcontroller address 0 / IO Main Alt. Type Description Input IOA1 2~16MA, SR Microcontroller address 1 / IO Input IOA2 2~16MA, SR Microcontroller address 2 / IO Input IOA3 2~16MA, SR Microcontroller address 3 / IO Input IOA4 2~16MA, SR...
Page 36
Input 1) Flash address 21 / IO IOA21 2~16MA, SR 2) While External FLASH size <= 2MB: I) GPIO Input 2~16MA, SR Microcontroller address latch enable PU, SMT Main Alt. Type Description IOOE# Input 2~16MA, SR Flash output enable, active low / IO IOWR# Input 2~16MA, SR...
Page 37
Input 1) Microcontroller port 3-0 UP3_0 4MA, SR 2) 8032 RS232 RXD PU, SMT Input 1) Microcontroller port 3-1 UP3_1 4MA, SR 2) 8032 RS232 TXD PU, SMT 1) Microcontroller port 3-4 Input 2) Hardwired RD232 RXD UP3_4 RXD SCL 4MA, SR 3) I C clock pin...
Page 38
Output Audio bit clock ABCK Fs64 Phase de-modulation Non-pull Input ACLK Audio DAC master clock Non-pull Audio serial data 0 (Front-Left/Front-Right) DSD data left channel Trap value in power-on reset : Input I) 1 : manufactory test mode ASDATA0 II) 0 : normal operation PD SMT While using external channels: I) GPO_2...
Page 39
APLLVDD3 Power 3.3V Power pin for audio clock circuitry APLLCAP Analog Input APLL External Capacitance connection APLLVSS Ground Ground pin for audio clock circuitry ADACVSS2 Ground Ground pin for AUDIO DAC circuitry ADACVSS1 Ground Ground pin for AUDIO DAC circuitry AUDIO DAC Sub-woofer channel output While internal GPIO Output...
Page 40
Output Video data output bit 5 YUV5 B/Cb/Pb 4MA, SR Blue or CB Output Video data output bit 6 YUV6 R/Cr/Pr 4MA, SR Red or CR Vertical sync input/output Input While no External TV-encoder: 4MA, SR VSYN V_ADIN1 I) Vertical sync for video-input II) Version AD input port 1 Non-pull III) GPIO...
Page 41
IO_5 Input Digital Video output C bit 5 (RD21) Non-pull GPIO IO_6 Input Digital Video output C bit 6 (RD22) Non-pull GPIO IO_7 Input Digital Video output C bit 7 (RD23) Non-pull GPIO Input IO_17 (DQM2) GPIO Non-pull IO_8 Input Digital Video output Clock YUVCLK (DQM3)
Page 42
CAS# output DRAM column address strobe, active low RWE# output DRAM Write enable, active low Input DQM1 Data mask 1 Input Non-pull IO_18 (DQS1) GPIO Input DRAM data 8 Input DRAM data 9 Input RD10 DRAM data 10 Input RD11 DRAM data 11 Input RD12...
Page 45
5. BA6208F The BA6208F is monolithic ICs used for driving reversible motors. It allows control of reversible motors in cassette players and other electrical equipment by using TTL-level logic signals. The IC contains a logic section, which controls forward and reverse rotations as well as forced stop, and an output power section, which can supply an output current of up to 100mA (typical) according to the logic control.
Page 46
7. MX29LV160BT 16M-BIT[2Mx8/1Mx16]CMOS SINGLE VOLTAGE 3V ONLY FLASHMEMORY...
Page 48
8. AT24C16 2-Wire Serial CMOS E PROM 16k (2048 x 8 ) The AT24C16 provides 16384 bits of serial electrically erasable and programmable read only memory (EEPROM) organized as 2048 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low power and low voltage operation are essential.
Page 51
10. WM8714 24-bit, 96kHz Stereo DAC The WM8714 is a high performance stereo DAC designed for audio applications such as DVD, home theatre systems, and digital TV. The WM8714 supports data input word lengths from 16 to 24-bits and sampling rates up to 96kHz. The WM8714 consists of a serial interface port, digital interpolation filters, multi-bit sigma delta modulators and stereo DAC in a 14-pin SOIC package.
Page 52
ICS ON HI-VOLTAGE BOARD 1. BIT3193 High Performance PWM Controller BIT3193 integrated circuit provides the essential features for general purpose PWM controller in a small low cost 16-pin package. BIT3193 has built-in a low frequency PWM generator for any specified application. BIT3193 includes latched off protection feature may make the system more reliable while compare to other similar products.
Page 53
Symbol Descriptions The inverting input of the error amplifier. Output of the error amplifier. LOAD A switch that connected to the high frequency triangle wave generator. This switch is open while ISEN pin <1.3V. An external resistor connected here may change the operation frequency of CTOSC in open load situation. CTOSC An external capacitor connected here can set the frequency of high frequency PWM controller.
Page 54
2. AP4511M N AND P-CHANNEL ENHANCEMENT MODE POWER MOSFET...
DVD BOARD 1. Index SLOTIN1389HD_TOHEI_HD62_V1 MT1389HD(LQFP256) DVD MP Board for SANYO HD62 PUH (Small Size) MDxxx History Date INDEX & POWER, RESET The original released. (modified from 3-SY1389P3-V1) 2005/10/08 MT1389HD Supports 1389HD & Memory Card Interface SDRAM & FLASH VIDEO OUT & AV-CON AUDIO OUT - WM8766 NAME TYPE...
Hi-voltage board Test Pannel: AU M170EG01 VIN 10.8~13.2V Lamp voltage 600Vrms Lamp output current 6.5mA Start-up time 1.2s Start-up voltage 1700Vrms Operation frequency 50KHZ...
Page 66
Part 5 Part list of LTD-61915E Bom No Part No Part Name 02.23.LTD06V3769C0 LTD06V-3769C01 DVD board Part No Name Specification LOCA NO R16 R17 R19 R22 R56 R57 R58 01.57.R.2.E000J SMD resistor 0603-0Ω ±5% R64 R82 R85 R90 R97 R78 R79 R77 R122 01.57.R.2.E1R0J SMD resistor...
Page 73
EV-015FC/15 01.40.CON.DCZ.E007 VGA jack 1 3CN10 pin DIP 01.40.CON.DCZ.E001 Jack DASW-8 DIP 1 3CN80 01.40.CON.DCZ.E323 Same core jack AV6-13/PB-27 1 3CN81 AV4-8.4-13/PB- 01.40.CON.DCZ.E170 Same core jack 1 3CN83 CKX-3.5-02(with 01.40.CON.DCZ.E102 Perch earphone jack 1 3CN11 out switch) DIP 01.40.CON.DCZ.E018 Power jack DDK2.5 DIP 1 1JP1 01.40.CON.DTJ.E004...
Page 78
Part 6 Debugging Procedures 1. Signal process diagram...
Page 79
2. Debugging Strategy Make sure the power adapter Debug start is correctly connected. Led red? Power on Led green? Check the connection between FLASH and FLI8125 FLASH LOGO appears? Check the speed of FLASH Accessed? EEPROM works Check the connection between EEROM and FLI8125 noramally? Check Pins of FLI8125 Video signal from...
Page 80
In DVD mode Check the Pin STB (147)of FL18125 is low Is tray works OK? Check Is signal of Can sled return to Motor SL+ SL- Position automatically? Driver BA6287 Check the circuit connected With the loader Focus operation Drive signal of F+/F- OK? Check periphery circuit of BA5954 Check circuit between laster head and BA5954...
Page 81
3. Tips Of Some Typical Troubleshooting White screen First check voltage in HI-voltage Board; otherwise check the voltage of MAIN board , if abnormal , the problem occurs in 1U1or 1U2. If the voltage is OK, check the LVDS. At last the connection between the main board and drive board may be the target for troubleshooting.