1. INTRODUCTION 1.1 Scope This specification defines the requirements for the 15” MICRO-PROCESSOR based Multi- mode supported high resolution color LCD DISPLAY, This LCD DISPLAY can be directly connected to general 15 pin D-sub VGA connector, eliminates the requirement of optional special display card.
2.1.1 MEASUREMENT SYSTEMS The units of measure stated in this document are listed below: 1 gamma = 1 nano tesla 1 tesla = 10,000 gauss cm = in x 2.54 lb = kg x 2.2 degrees F = [°C x 1.8] + 32 degrees C = [°F - 32]/1.8 u' = 4x/(-2x + 12y + 3) v' = 9y/(-2x + 12y + 3)
2.3 LCD Panel Specification 2.3.1 LCD Panel Model • Display Type TN active matrix color TFT LCD • Resolution V:768 lines , H:1024 pixels • Display Dot 1024 x (RGB) x 768 • Display Area 304.128mm(H) x 228.096mm(V) • Pixel Pitch 0.297mm(H) x 0.297mm(V) •...
2.3.2 Optical Characteristics Item Symbol Condition Min. Typ. Max. Unit Note Contrast (1)(2) Response Rising Tr+Tf time msec (1)(3) Falling White Luminance Cd/m (center of screen) θ=0∘ Φ=0∘ 0.613 0.643 0.673 Normal Viewing 0.305 0.335 0.365 Angle 0.267 0.297 0.327 Color Green chromaticity...
Page 10
Note (2) Definition of Contrast Ratio (CR): Measured at the center point of panel Luminance with all pixels white (L63) CR= ——————————————— Luminance with all pixels white (L0)
Page 11
Note (3) Definition of Response Time: Sum of T and T Note (4) Optical characteristic measurement setup...
Page 12
Note (5) Brightness is measured at the center point of brightness value with all pixels displaying white. 90 % 50 % 10 % 10 % 50 % 90 % Unit: percentage of dimension of display area Note 5: Brightness uniformity of these 9 points is defined as below: (Min.
2.4.4 Support Modes There will be 16 total support modes to accommodate the above mode and other video modes within the frequency range of the monitor. 2.4.4.1 PC model control function Bright , Contrast , Picture position , OSD position , Auto adjustment , Clock , Phase , OSD Transparence , Language , Color Temperature Graphic/Text select 2.4.5 Video input Connector Analog Video input Connector: 15pins mini D-Sub...
2.4.6 STANDARD ACCESSORIES ANALOG VGA CABLE Type Worldwide type Length 1.8m + 5cm/-5cm Color black Connectors Monitor -side 15 pin D-Sub Blue compliant with POWER CABLE Type Worldwide type Length 1.8m + 5cm/-5cm Color black Connectors Monitor -side IEC 320 female Mains-side 1.8m + 5cm/-5cm Length...
2.5 CONTROLS Control panel (monitor front panel) 7. Source mode and OSD Menu off function key control. . Power LED, will be green when monitor is on; be amber when in power saving mode. 6. Adjust decrease and volume control. .
2.5.1 OSD Functions • OSD Format: Refer to following figure. • OSD Border: Cyan color • OSD Tunable Item: The 15 icons that around the border. • Selected Item: Yellow background • Comment: Magenta foreground, Blue background page format :Monitor function Description : •...
User R: Red signal gain by user defined. User G: Green signal gain by user define. User B: Blue signal gain by user defined. 6500: set CIE coordinate at 6500°K color temperature (when use 6500°k color temperature, contrast display cannot change and cannot adjust). ...
User: User R: Red signal gain by user defined. User G: Green signal gain by user define. User B: Blue signal gain by user defined. 6500: set CIE coordinate at 6500°K color temperature (when use 6500°k color temperature, contrast display cannot change and cannot adjust). ...
2.7.4 Power Management 2.7.4.1 Meet VESA DPMS proposal The monitor must comply with the Microsoft On Now specification, with a minimum of three power management states, as defined by the VESA DPMS document. The front panel of the monitor must appropriately display the DPMS state, For example: DPMS ON : The power LED is Green...
2.9 Audio Technical specification 2.9.1 General Description: Output power : 2.5W + 2.5W maximum Total harmonic distortion : Less than 2 % (except speakers distortion) Input signal sensitivity : 0.5 Vrms for full output Input impedance : 47 Kohm +/- 5 % Frequency response range : 20Hz –...
3. MECHANICAL REQUIREMENTS 3.1 Vibration and Shock All testing shall be done in each of three mutually perpendicular axes, referenced to the position of the system as it is in front of the user (i.e., front-to back, side-to-side, and top-to- bottom).
3.3 Dimension Size and Weight Dimension size 430(W)×325.5(H)×198(D) 4.0 Kg ± 0.3 Kg Net Weight 5.8 Kg ± 0.3 Kg Gross Weight 3.4 Gap Spec. 3.4.1 The step between front bezel and back cover shall be within specification. Back Cover & Bezel Gap Neck Front &...
0.8 mm ≤ E ≤ 1.2 mm SLV85A-E09 Back Cover & Key Plate 0.6 mm ≤ F ≤ 1.2 mm SLV85A-E10 3.4.2 LCD Horizontally The angle between front bezel and LCD unit in bottom side should be not large than 1.0mm.
The distance G-H of the LCD display unit from left side to right should be not large than 4.0 mm. SLV85A-E12 3.4.3 Gap between panel with bezel is 0.2 mm < gap <1.5 mm CM870-E18 3.5 Tilt Base Rotation Tilt up 25:1 / down 5:1 3.6 Plastic Material Front Bezel ABS 94HB, 94V-0 Back Cover ABS 94HB, 94V-0...
TEST CONDITIONS & PROCEDURE: (Follow IEC 61000-4-4) Test Condition: The condition is base on operating with 50Ω load. 4.1 Peak Voltage 2 KV (applies the Level 3 typical Industrial Environment” of IEC 61000-4-4) 4.2 Polarity : + / - 4.3 Repetition Frequency of the impulse: 5 KHz. ±...
5.1 Climatic Condition The climatic conditions shall be within the following ranges: ° ° 5.1.1 Ambient Temperature: 15 C to 35 5.1.2 Relative Humidity: 10% to 75% 5.1.3 Atmospheric Pressure 86kPa (860 mbar ) to 106kPa (1060mbar) Note: The temperature and relative humidity should be recorded in the test report. 5.2 Test Conditions: 5.2.1 Wave-shape of the current surge: (refer to IEC 61000-4-5) Open circuit voltage:...
6.1 Operating Temperature 5°C ~ 40°C Relative Humidity 20% to 80% Altitude Sea level to 8000ft 6.2 Storage or Shipment Temperature -20°C ~ +60°C Relative Humidity 5% to 85% Altitude Sea level to 40,000ft 6.2.1 TEST PROCEDURE: • Put in temperature chamber under 60°C Time:24 hours •...
7. REGULATION COMPLIANCE This product complies with the most current revisions of following regulations: UL/CUL Standard for Safety of Information Technology Equipment including Electrical Business Equipment {UL 60950/ CSA C22.2 NO60950-00} EN 60950/CB Scheme Safety of Information Technology Equipment including Electrical Business Equipment MPR 1990:8 Test methods for visual display units.
7.2 Electrostatics Discharge (ESD) E.S.D Test This test follow the IEC 61000-4-2 Discharge Voltage Level : Criteria Contact Discharge (KV) Air Discharge(KV) Class C ±4 ±4 Class B ±6 ±8 Class A ±8 ±15 Class A : Temporary degradation or loss of function or performance which requires operator Intervention or system reset.
Ambient temperature : 15°C to 35°C Relative humidity : 30% to 60% 8. QUALITY AND RELIABILITY 8.1 QUALITY ASSURANCE Unless otherwise specified in this specification or the applicable purchase order, the supplier shall be responsible for maintaining a statistical process program or performing inspections that are sufficient to assure that the parts supplied meet the requirements specified herein.