Copyright Copyright (C) 2005 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted.
Page 3
Revision User’s Manual for PLANET 802.11g SIP VoIP Router: Model: VIP-462DG Rev: 1.0 (Sept. 2005) Part No. EM-VIP462DGV1...
LAN IP address configuration via web configuration interface...14 WAN IP address configuration via web configuration interface ...15 Chapter 3 Network Service Configurations... 16 Configuring and monitoring your VIP-462DG from web browser...16 Overview on the web interface of VIP-462DG ...16 Manipulation of VIP-462DG via web browser ...16 Chapter 4 General Configurations ...
With advanced router/firewall, and VoIP DSP processor technology, the VIP-462DG is able to make calls via SIP proxy voice communications, plus the IP sharing, QoS, and the SPI firewall mechanism, VIP-462DG is the ideal choice for Voice over IP communications and providing integrated Internet sharing for the daily tasks.
DECT Features • DECT & GAP Compatible • Base can register up to 8 Handsets • Intercom call during external call, Call transfer between • handsets , three-way telephone meeting • CID 50 locations • Redial memory: 3 locations, 20 digits •...
LED Display & Button LED Indicators Light: power on, normal operaion Blink: firmware loading Off: power off or failure Light: connection is active Blink: data transmitting or receiving Off: connection is not established VoIP Light: SIP proxy registration is successful Blink: SIP proxy registration is unsuccessful Off: SIP proxy registration is disable WLAN...
Page 10
Back Panels DC12V Power Adapter connecter RESET (Reboot) Press for one second to reset the device or press for 5 seconds to reset to the factory default. 10/100Mbps RJ-45 connector connect to ADSL or cable modem LAN 1 ~ LAN 4 10/100Mbps RJ-45 connector connect to PC or local switch/hub.
Keypad and button definition on DCT-100 Number 0 –9 and # DCT-100 installation The three rechargeable Ni-MH batteries (AAA size) come with your phone. Install the batteries before using your phone. 1. Slide the battery cover in the direction of the arrow and pull it out. 2.
Page 12
This phone won't work by itself. It should be registered Note to the main base unit inside the VIP-320. Before initial using, it should be charged for 24 hours. Reversing the orientation may damage the handset. The battery needs to be replaced if it does not recover Note its full storage capacity after recharging.
Microsoft Internet Explorer 5.5 or higher with Java support Default LAN interface IP address of VIP-462DG is 192.168.0.1. You may now open your web browser, and insert 192.168.0.1 in the address bar of your web browser to logon VIP-462DG web configuration page.
LAN/WAN Interface quick configurations Nature of PLANET VIP-462DG is an IP Sharing (NAT) device, it comes with two default IP addresses, and default LAN side IP address is “192.168.0.1”, default WAN side IP address is “172.16.0.1”. You may use any PC to connect to the LAN port of VIP-462DG to start machine administration.
WAN IP address configuration via web configuration interface Execute your web browser, and type http://172.16.0.1 in the adddress bar. If you’re using WAN port login the VIP-462DG, please be sure Hint to check if the “Rermote Management” is enabled in machine.
Provides user input data fields, check boxes, and for changing machine configuration settings Displays machine running configuration To start VIP-462DG web configuration, you must have one of these web browsers installed on computer for management Netscape Communicator 4.03 or higher Microsoft Internet Explorer 5.5 or higher with Java support...
NTP servers in your area Password Settings Set the password of the user. The Idle Time Out value is used for VIP-462DG to log out automatically when no access to the web after this timeout value.
The remote user can login using WAN IP. The default port Hint number is 8080. WAN Settings The VIP-462DG supports 3 types of WAN connection: Dynamic IP (DHCP Client) PPPoE Static IP (factory deault value)
The Host Name is optional, but may be required by some Service Provider’s. The default MAC address is set to the WAN’s physical interface on the VIP-462DG. If required by service provider, you use the “Clone MAC Address” button to copy the MAC address of the Network Interface Card installed in your PC and replace the WAN MAC address with this MAC address.
Static IP If your service provider has assigned a fixed IP address, enter the assigned IP address, subnet mask and the gateway address provided. Most service providers provide a DNS server for speed and convenience. If there is a DNS server that you would rather use, you need to specify the IP address here.
The domain name field is empty in most case. In some special ISP need input domain name field. Wireless Setting VIP-462DG can be quickly configured as a wireless access point for roaming clients by setting the service set identifier (SSID) and channel number. It also supports data encryption and client filtering.
This page allows you to define SSID, Transmission Rate, Basic Rate and Channel ID for wireless connection. In the wireless environment, VIP-462DG can also act as a wireless access point. These parameters are used for the mobile stations to connect to this access point.
Page 24
WPA is a security enhancement that strongly increases the level of data protection and access control for existing wireless LAN. Matching authentication and encryption methods must be setup on your VIP-462DG and wireless client devices to use WPA.
This page sets up the phone number and username/password for SIP server registration. The phone number and username/password must be predefined in SIP Proxy. You can register two VoIP number to VIP-462DG, register one number for analog telephone set and the other number for DECT handset.
SIP Setting This page defines the SIP parameters, in the SIP Parameters setting, we need to set SIP domain and SIP Proxy IP address. The default register expire time is 1800 second. So the system must reregister to SIP proxy again within register expire time. VoIP adanced setting This page allows you to configure advanced VoIP features including voice Codec configuration.
Port advanced Setting and register DECT handset This page allows you adjust the parameter of voice channel to achieve better sound quality. In this page also provide DECT setting for you to paging and register new DECT handset. Qos Settings The bandwidth gap between LAN and WAN may significantly degrade performance of critical network applications, such as VoIP, gaming and VPN.
Traffic mapping Up to 16 rules can be defined to classify traffic into Diffserv forwarding groups and outgoing VCs. Edit Traffic class This page is for user to specify a classify rule, First, define the class by traffic type and the local and remote addresses, then set the Diffserv forwarding group this class is mapped to, finally select the outgoing VC that traffic of this class would be routed to.
Traffic Statistics This page shows the WAN outbound traffic statistics of all of the Diffserv forwarding groups in the last 12 hours (automatically updated every 5 mins). NAT Settings Network Address translation (NAT) allows multipleusers at your local site to access the Internet through a signal public IP address or multiple public IP address.
Virtual Server VIP-462DG is a NAT router. All the IP addresses coming in and going out to VIP-462DG can be converted between public and private IP addresses. You can configure VIP-462DG as a virtual server so that remote users accessing services such as the Web or FTP at your local sites via public IP address can be automatically redirected to local servers configured with private IP address.
Page 31
Some of the popular applications and protocol/port numbers mapping are defined below: Application Protocol Port Number Telnet SMTP POP3 H.323 SNMP SNMP Trap HTTP PPTP PC Anywhere TCP PC Anywhere UDP 1720 1723 5631 5632...
Special Application Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications cannot work when Network Address Translation (NAT) is enabled. If you need to run applications that require multiple connections, specify the port normally associated with an application in the "Trigger Port"...
Firewall Setting VIP-462DG provides extensive firewall protection by restricting connection parameters to limit the risk of hacker attack, and defending against a wide array of common attacks. When firewall is enabled, extra checking will be performed for each packets passing through the device, the performance of the device will be greatly affected.
Page 34
“WWW” and “E-mail Sending”, and press “OK” button. The follow page will show up. After the setup, the PC with IP address192.168.0.100 will not be able to use WWW and sending e-mail. VIP-462DG can supports up to 32 filtering rule.
MAC Filter User can enter up to 32 MAC address, the PCs with these MAC addresses will not be permitted to access Internet. URL Blocking You can block access to certain Web sites from a particular PC by entering either a full URL address or just a keyword of the Web site.
As shown above, all of the URL with ”violence” pattern cannot be accessed. The users within LAN site cannot access to any web-site with “violence” in its URL address. User can enter up to 32 MAC address, the PCs with these MAC addresses will not be permitted to access Internet.
As shown above, we defined a schedule rule called “Office Hour”, the active time period is Monday to Friday, 9:00 am to 5:00 pm. After pressing “OK” button, the following page will show up: Then when we go to “Access Control” page, select “Add PC”, in the bottom of the page “Access Control Add PC”, the scheduling rule will show “Office Hour”, as shown below: If we setup the PC of RDM department in our company (IP address 192.168.0.101 to 192.168.0.130) can not access Web during office hour, then in “Access Control”...
RIP Defect Discard PING from WAN When hacker tries to attack, VIP-462DG can send e-mail alert to the specified user. Enter related e-mail information such as e-mail address and SMTP server. Some e-mail service providers require user to enter POP3 information when trying to send e-mail. In this case, enter the POP3 server, user name and password;...
UPnP The Universal Plug and Play architecture offers pervasive peer-to-peer network connectivity of PCs of all form factors, intelligent appliances, and wireless devices. UPnP enables seamless proximity network in addition to control and data transfer among networked devices in the home, office and everywhere in between.
VIP-462DG’s current configuration to a file named “backup_config.bin” on your PC. Users can then use “Restore” tool to restore the saved configuration to the VIP-462DG. The “Reset to Factory Defaults” tool will force the configuration of VIP-462DG back to the original factory setting and perform a power reset.
Reset In the event that the system stops responding correctly or in some way stops functioning, you can perform a reset. Your settings will not be changed. To perform the reset, click on the “APPLY” button below. You will be asked to confirm your decision. The reset will be complete when the power light stops blinking Status The status page displays the status of the system, including the connection status of the interfaces,...
Device Status The Device Status page displays the current setting of this device, including IP address, Subnet mask, DHCP server, Firewall and UPnP. Security Log This page provides the system security log record when device boot, including user login/logout, hack attach, PPPoE connection, NTP connection, Get IP from DHCP.
VoIP Status This page displays the gateway status, including Port type, port Status, time information of each call and Destination. This page also displays SIP proxy registration status. User must make sure SIP proxy registration is successful. User can press “Refresh” button to update current VoIP status.
Appendix A VIP-462DG Specifications Product 802.11g SIP DECT VoIP Router Model VIP-462DG Hardware 1 x 10/100Mbps RJ-45 port 4 x 10/100Mbps RJ-45 port WLAN IEEE 802.11b /802.11g compatible PSTN 1 x RJ-11 connection Phone 1 x RJ-11 connection DECT 1 x DECT GAP compatible base...