Subscribe to Our Youtube Channel
Related Manuals for bolid ShPS-12
Summary of Contents for bolid ShPS-12
- Page 1 SрPS-12 FIRE EQUIPMENT MOUNT BOXES WITH BACKUP BATTERY POWER SUPPLIES ShPS-12 ShPS-12 mod.01 ShPS-12 mod.02 ShPS-12 mod.10 ShPS-12 mod.11 ShPS-12 mod.12 User’s Manual...
-
Page 2: Table Of Contents
Operating Restrictions ......................... 13 Preparing for Use ......................... 13 2.2.1 Safety Precautions ........................13 2.2.2 ShPS-12 Design ........................... 13 2.2.3 Mounting the ShPS-12 ......................... 13 2.2.4 Wiring the ShPS-12 ........................14 2.2.5 Programming the ShPS-12 ......................15 2.2.6 Usage ............................16 2.2.7 Performance Testing ........................ -
Page 3: Description And Operation
12 mod.12 boxes differ from ShPS-12 mod.10 ones by IP54 ingress protection rating. ShPS-12 mod.10, ShPS-12 mod.11, ShPS-12 mod.12 boxes differ from ShPS-12, ShPS-12 mod.01, ShPS-12 mod.02 boxes by two separate RS-485 interface lines (instead of one line, see Clause 1.2.9). -
Page 4: Specifications
(S2000M panel, Sirius panel, or workstation with Orion Pro Suite) over the RS-485 interface. 1.1.11. ShPS-12 boxes can issue fault messages to the remote output, which is the solid state relay output circuit with galvanic isolation. - Page 5 When the output current exceeds 3.5 A, the ShPS-12 box turns off the charger. When the output current is over 4A, ShPS-12 disables the output voltage.
-
Page 6: Scope Of Delivery
1.4.1. A ShPS-12 is assembled within a metal enclosure. The enclosure consists of a cabinet and a key lockable door. On the outer surface of the door there are light indicators to indicate the ShPS-12 conditions. The cabinet houses the MIP-12 power supply module, the BK-12 switch unit for connections, and circuit breakers for connecting the mains 220 V and connecting power consumers to the mains. - Page 7 Table 3 and Table 7. If some light indicator performance differs from that described in Table 3 and Table 7 or some deviation from normal operation of the ShPS-12 is detected, please contact the Bolid technical support (please refer to 4 for contact information).
- Page 8 If in the moment of message generation there is no connection with a network controller over RS- 485, the message is stored in non-volatile memory of ShPS-12, and it will be transmitted as soon as the connection is recovered. The time stamp of message will get the actual time of the event occurrence.
- Page 9 To request the status of the ShPS-12 using the S2000M panel (see S2000M User’s Guide): Enter a passcode CODE:_ Select the View Input Status using the43 buttons and press , or press 5 v5 VIEW INPUT STATUS for quick navigation...
- Page 10 Note: * The mains voltage measured by the ShPS-12 can differ if compared to values measured with a RMS voltmeter. This may be due to distortion of mains power y-voltage, etc. The ShPS-12 can adjust the main voltage measurements with a 1V increment (in ±20V range). To adjust the measurements, please run the UProg utility, select the MIP-12-3A RS with the corresponding network address, and select the values to be adjusted in the appeared dialog box.
-
Page 11: Measuring Instruments, Tools, And Accessories
RS-485 interface by means of the Orion_prog utility (“Firmware Update”). The last version of this program is available online at the address of http://bolid.ru. To switch the BK- 12-RS485 to the programming mode, please close the jumper circuit ХР5 (“PROG”) on the board of the BK-12-RS485. -
Page 12: Packaging
Examples of equipment layout can be downloaded at http://bolid.ru/files/373/566/Primery_raspolozheniya_oborudovaniya.zip. If necessary, the equipment can be installed on the wall of the ShPS-12 box; please remove unused rails for this purpose. Also, please remove transporting tie-wraps from the BK-12 and MIP-12 prior to operating ShPS-12. -
Page 13: Wiring The Shps-12
Upon erecting wires and cables passed through within ShPS-12, ShPS-12 mod.01, ShPS-12 mod.10, ShPS-12 mod.11 via upper cable glands, use a sealant (gasket maker) to seal inputs to provide IP41 enclosure protection degree. For this purpose, white organosilicone one-part sealant “ВГО-1” is advised. -
Page 14: Programming The Shps-12
2.2.5.6. Unless the ShPS-12 / ShPS-12 mod.01 / ShPS-12 mod.02 box is the first or the last device in the RS-485 interface bus then open the XP1 jumper located on the BK-12 board close to the ХТ1 terminal block (which is intended for connecting the devices) –... -
Page 15: Usage
7. Enclosure tampering 2.2.6 Usage 2.2.6.1. Please refer to 1.4.2 for description of ShPS-12 operation. To be admitted to work with the equipment, the personnel are obliged to have studied this manual and to have a certificate of verification of knowledge of accident prevention regulations. -
Page 16: Performance Testing
Disconnect the batteries. d) Disconnect the load. 2.2.7 Performance Testing 2.2.7.1. A full testing of the ShPS-12 performance is carried out only by the manufacturer or in special labs. 1) Turn on the ShPS-12 in line with 2.2.6.2. 2) Check operation of the ShPS-12, its indicators and its buzzer against the Table 3. Measure the output voltage at the BK-12;... - Page 17 To measure the ShPS-12’s battery capacity using the Orion Pro tools (see Orion Pro User Guide), please click the ShPS-12 icon on the map in the Orion Pro Monitor module, select the item next to icon ( it shows the device’s address and name): Note: The MIP-12-3A RS icon shall already be added to the map.
-
Page 18: Extreme Situation Actions
In case of successive receiving of this command, the ShPS-12 executes it and issues the Test Starts event. The procedure of capacity measurement completes automatically. Upon completing the procedure the ShPS-12 issues the Test Ends event. d) To measure the battery capacity without using commands over RS-485, conduct the following: 1) Make sure the batteries are charged higher than 80% (indicated by steady lit BAT LED);... -
Page 19: Maintenance Procedures
3.3 Maintenance Procedures 3.3.1 To inspect the ShPS-12 and batteries visually means to verify that it has no mechanical damages and is fastened reliability, verify that conditions of connecting wires and contact joints are good, and batteries are undeformed with no electrolyte leakage. -
Page 20: Manufacturer Warranty
TR EAEU 043/2017 ‘On Requirements for Fire Safety and Fire Extinguishing Equipment’ and are covered by the conformity certificate No. RU С-RU.ЧС13.В.00108/21. 9.3 Production of ShPS-12 is awarded with the conformity certificate GOST R ISO 9001. The certificate can be found at the website http://bolid.ru... - Page 21 ХТ2...
- Page 22 Schematic for Wiring ShPS-12 mod.10, ShPS-12 mod.11, ShPS-12 mod.12...
- Page 23 Appendix B (For reference) Example No.1 of fitting together equipment within ShPS-12...
- Page 24 Appendix C (For reference) Example No.2 of fitting together equipment within ShPS-12...
- Page 25 Appendix D (For reference) Example of Arranging Equipment on the Door of ShPS-12, ShPS-12 mod.02, ShPS-12 mod.10, or ShPS-12 mod.12 using MK-1 ShPS Mounting Kit READY READY RS-485 LOOP S2000-KDL SIGNAL-10 READY READY MASS PRES S2000-KPB S2000-4...
- Page 26 Appendix E Overall and Mounting Dimensions For ShPS-12, ShPS-12 mod.02, ShPS-12 mod.10, ShPS-12 mod.12 Шпильки для DIN Rail Pins установки реек...
- Page 27 Appendix F Overall and Mounting Dimensions For ShPS-12 mod.01 and ShPS-12 mod.11...
- Page 28 Appendix G (For reference) Window Sizes and Position on the Door ShPS-12 mod.01 and ShPS-12 mod.11...
- Page 29 Appendix H (For information) UProg Window for Programming ShPS-12...
Need help?
Do you have a question about the ShPS-12 and is the answer not in the manual?
Questions and answers