Table of Contents
Advertisement
Quick Links
20 TON SHOP PRESS
WITH OIL FILTER CRUSHER
SET UP aNd OPERaTINg INSTRUCTIONS
distributed exclusively by Harbor Freight Tools
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SaVE THIS maNUaL.
©
Copyright
2008 by Harbor Freight Tools
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
3491 Mission Oaks Blvd., Camarillo, CA 93011
®
. All rights reserved. No portion of this manual or any artwork
65330
®
.
Advertisement
Table of Contents
Related Manuals for Harbor Freight Tools Central Hydraulics 65330
Summary of Contents for Harbor Freight Tools Central Hydraulics 65330
- Page 1 Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.
-
Page 2: Safety Alert Symbol And Signal Words
SaVE THIS maNUaL NOTICE is used to address practices Keep this manual for the safety warn- not related to personal injury. ings and precautions, assembly, operating, CaUTION, without inspection, maintenance and cleaning pro- the safety alert cedures. Write the product’s serial number symbol, is used to address in the back of the manual (or month and practices not related to... -
Page 3: Personal Safety
Keep bystanders, children, and visi- Never leave a compressed workpiece tors away while operating the Shop unattended. Whenever a workpiece Press. Distractions are able to result is compressed, there is a very large in the loss of control of the tool. amount of force that has been stored in the workpiece which must be con- Personal safety... - Page 4 control of the tool in unexpected situ- Use clamps or another practical way ations. to secure and support the workpiece to Arbor Plates and Press Apron. Use safety equipment. A Holding the work by hand or against dust mask, non-skid safety the body is unstable and is able to shoes and a hard hat must lead to loss of control.
-
Page 5: Air Source
air source Check for misalignment or binding of moving parts, breakage of parts, and Never connect to an air any other condition that affects the source that is capable of Shop Press’ operation. If damaged, exceeding 120 PSI. Over have the Press serviced before using. pressurizing the tool may Many accidents are caused by poorly cause bursting, abnormal operation,... -
Page 6: Product Specifications
Washers (2), and four Nuts (1). any parts are missing or broken, please (See assy. diagram.) call Harbor Freight Tools at the number Attach one end of the Springs (5) to shown throughout the manual as soon as the mounting holes on the Top Cross possible. -
Page 7: Air Supply
With the help of another person, elevate and position the Air/Hydraulic Jack (21) to Top Cross Beam (22). Tighten Set Screw (25) against Ram top of the Jack. Raise Frame (7) and tighten Nut (10) to secure the Jack (21). (See assy. diagram.) Tighten all Nuts and Bolts. - Page 8 ous diagram. an in-line shutoff allow it to build up pressure until it valve is an important safety device cycles off. because it controls the air supply Adjust the air compressor’s output should the air hose rupture. regulator so that the air output is Note: If an automatic oiler system is not enough to properly power the tool, used, add a few drops of Pneumatic...
- Page 9 OPERaTINg INSTRUCTIONS Lower the Filter Crushing Head (13), making sure the Crushing Head can Read the ENTIRE ImPORTaNT be lowered into the Crushing Hous- SaFETy INFORmaTION ing (14). (See assy. diagram.) section at the beginning of this Raise the Crushing Head (13) all manual including all text under the way up by opening the Release subheadings therein before set...
- Page 10 Close the Release Valve on the Air/ If you will use the unit as a general Hydraulic Jack. (See air/Hydraulic Shop Press: jack Owner’s manual.) To operate the Shop Press as a Then squeeze and hold the Lever of general Press, remove the Crushing the Air/Hydraulic Jack.
-
Page 11: Maintenance Instructions
maINTENaNCE The lubricator’s oil level needs to be maintained and the moisture filter INSTRUCTIONS must be regularly drained. Perform- ing routine maintenance on the air Procedures not specifically supply will allow the Shop Press to explained in this manual operate more safely and will also must be performed only by a reduce wear on the Press. -
Page 12: Troubleshooting
TROUbLESHOOTINg Problem Possible Causes Possible Solutions Shop Press does Pressure Release Valve open. Close Valve. not work, or Air compressor’s Regulator Set Regulator between 110 PSI and 120 does not operate not set at between 110 PSI maximum PSI. at its optimum and maximum 120 PSI. -
Page 13: Assembly Diagram
aSSEmbLy dIagRam SKU 65330 For technical questions, please call 1-800-444-3353. Page 13... -
Page 14: Limited 90-Day Warranty
LImITEd 90 day WaRRaNTy Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this prod- uct is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
Need help?
Do you have a question about the Central Hydraulics 65330 and is the answer not in the manual?
Questions and answers