Variable-speed rotary tool with flexible shaft (20 pages)
Summary of Contents for Harbor Freight Tools CENTRAL MACHINERY 46199
Page 1
2001 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions please call 1-800-444-3353...
Brought to You By Augusta Flint SPECIFICATIONS TABLE Item Description Electrical Requirements 3/4HP Motor / 120V 60Hz / Single Phase Lathe Specifications 16-1/2” Swing Over Bed 15-3/4” Distance Between Centers 3/4” Spindle Bore Diameter MT3 Spindle Taper 16-1/8” Longitudinal Travel 3-9/64”...
Page 3
REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacement parts. Only use accessories intended for use with this product. Approved accessories are available from Harbor Freight Tools. MAINTAIN THIS PRODUCT WITH CARE. Keep this tool clean and dry for better and safer performance.
Brought to You By Augusta Flint WARNING: The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be under- stood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
Page 5
Brought to You By Augusta Flint DO NOT FORCE THE EQUIPMENT. The Multi-Purpose Machine will do the work better and safer at the speed and capacity for which it was designed. KEEP ALL GUARDS IN PLACE AND IN WORKING ORDER. REMOVE ALL ADJUSTING WRENCHES FROM THE MULTIPURPOSE MACHINE BEFORE TURNING IT ON.
Brought to You By Augusta Flint INSTALLATION INSTRUCTIONS To Install The Multi-Purpose Machine Onto A Workbench: Make sure the workbench upon which the Machine is to be located is flat, level, and sturdy enough to bear the weight of the machine, its accessories, and work- ing material.
Page 7
Brought to You By Augusta Flint With assistance, slowly and carefully lift the Machine off the wooden shipping pallet and temporarily set the Machine on a flat, level, sturdy floor surface. With assistance, set the wooden shipping pallet onto the workbench where the Machine will be permanently positioned.
Page 8
Brought to You By Augusta Flint A. Lathe/Mill Selector Knob H. Tool Post Lock Lever B. Combined Switch I. Cross Feed Hand Wheel C. Shaft Clamp Lever J. Tailstock Barrel Clamp Lever D. Vertical Motion Lever K. Tailstock Barrel Adjusting Handwheel E.
Page 9
Brought to You By Augusta Flint The Milling/Drilling Spindle: First you will need to choose which function you want to use (either milling operation or lathe operation). Take off black plastic cover over the Lathe/Mill Selector Knob (A). For lathe operation rotate the Knob and push it INWARD. For mill operation, rotate the Knob and pull it OUT.
Page 10
Brought to You By Augusta Flint V-BELT CONE PULLEY (#79) CONE PULLEY (#95) FIGURE E The Longitudinal Feed: Use the Longitudinal Motion Lever (part #M) to slide the Tail Stock along the bedways horizontally. The Tail Stock can be unlocked and locked in position using the Tailstock Lock Lever (part #L).
Brought to You By Augusta Flint CHANGING THE LATHE SPEEDS To change the lathe speed you must first remove the Pulley Shell (36) which is attached by the two Bottom Head Screws (35). Next you must create slack in the V-Belt (23) by turning the Movable Joint Bolt (167) counterclockwise.
Page 12
Brought to You By Augusta Flint REV 06/06 SKU 46199 For technical questions, please call 1-800-444-3353. Page 12...
Brought to You By Augusta Flint PARTS LIST PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFER- ENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
Page 14
Brought to You By Augusta Flint PARTS LIST SKU 46199 For technical questions, please call 1-800-444-3353. Page 14...
Page 15
Brought to You By Augusta Flint PARTS LIST SKU 46199 For technical questions, please call 1-800-444-3353. Page 15...
Page 16
Brought to You By Augusta Flint PARTS LIST SKU 46199 For technical questions, please call 1-800-444-3353. Page 16...
Page 17
Brought to You By Augusta Flint PARTS LIST SKU 46199 For technical questions, please call 1-800-444-3353. Page 17...
Page 18
Brought to You By Augusta Flint PARTS LIST SKU 46199 For technical questions, please call 1-800-444-3353. Page 18...
Page 19
Brought to You By Augusta Flint PARTS LIST SKU 46199 For technical questions, please call 1-800-444-3353. Page 19...
Page 20
Brought to You By Augusta Flint PARTS LIST SKU 46199 For technical questions, please call 1-800-444-3353. Page 20...
Brought to You By Augusta Flint ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 46199 For technical questions, please call 1-800-444-3353. Page 21...
Page 22
Brought to You By Augusta Flint ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 46199 For technical questions, please call 1-800-444-3353. Page 22...
Page 23
Brought to You By Augusta Flint ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 46199 For technical questions, please call 1-800-444-3353. Page 23...
Page 24
Brought to You By Augusta Flint ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 46199 For technical questions, please call 1-800-444-3353. Page 24...
Need help?
Do you have a question about the CENTRAL MACHINERY 46199 and is the answer not in the manual?
Questions and answers