Makita DVP181 Instruction Manual page 7

3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
If electrolyte gets into your eyes, rinse them out
4.
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing battery cartridge in a
container with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current
ow, overheating, possible burns and even a
breakdown.
6. Do not store and use the tool and battery
cartridge in locations where the temperature
may reach or exceed 50°C (122°F).
7. Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
10. Follow your local regulations relating to
disposal of battery.
11. The contained lithium-ion batteries are subject to
the Dangerous oods Legislation re uirements.
When dis p os i ng the battery c a rtridge, remov e it
from the tool and dis p os e of it in a s a fe plac e . Follow
y o ur loc a l regulations relating to dis p os a l of battery.
12. Use the batteries only with the products
specified by Makita.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
14. During and after use, the battery cartridge may
take on heat which can cause burns or low
temperature burns.
15. Do not touch the terminal of the tool immediately
after use as it may get hot enough to cause
burns.
16. Do not allow chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery
cartridge. It may res u lt in poor performance or
break d own of the tool or battery c a rtridge.
17. Unless the tool supports the use near a high-
voltage electrical power lines, do not use the
battery cartridge near a high-voltage electrical
power lines.
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
Us e of non-genuine Mak i ta batteries , or batteries that
hav e been altered, may res u lt in the battery burs t ing
causing fires, personal injury and damage. It will also
v o id the Mak i ta warranty for the Mak i ta tool and c h arger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Charge the
3.
temperature at 10°C - 40°C (50°F - 104°F). Let a
hot battery cartridge cool down before charging
it.
4. When not using the battery cartridge, remove it
from the tool or the charger.
5. Charge the battery cartridge if you do not use it
for a long period (more than six months).
PARTS DESCRIPTION
Fig.1:
1. Intak e port 3/8"
2. Gas ballast v a lv e
3. Oil fill/Exhaust cap
4. Intak e port 5/16"
5. Sight glas s
6. Drain v a lv e
7. Oil tank
8. Area around pump
9. Solenoid v a lv e
10. Bas e
11. Motor
FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the pump is
switched off and the battery cartridge is removed
before adjusting or checking function on the pump.
Installing or removing battery
cartridge
CAUTION:
Always switch off the pump before
installing or removing of the battery cartridge.
CAUTION:
Hold the pump and the battery
cartridge firmly when installing or removing battery
cartridge. Failure to hold the pump and the battery
cartridge firmly may cause them to slip off your hands
and res u lt in damage to the pump and battery c a rtridge
and a personal injury.
Fig.2:
1. Red indic a tor
2. Button
7 ENGLISH
battery cartridge with
12. LED lamp
13. Power s w itc h
14. Battery guard
15. Battery holder
16. Battery (on the Left
port)
17. Battery (on the Right
port)
18. Handle
19. Wiring c o v e r
3. Battery c a rtridge
room