Sony XAV-601BT Service Manual page 62

XAV-601BT
Pin No. Pin Name
149 DAC4
150 VDDDAC
151 DAC3
152 DAC2
153 VDDDAC
154 DAC1
155 RSET
156 GNDDACBS2
157 RFP
158 RFN
159 VDD1AFE
160 A
161 B
162 VDDAFE
163 C
164 D
165 J
166 E
167 K
168 F
169 GNDAFE
170 G
171 H
172 GND1AFE
173 VC
174 VREF
175 RESOUT
176 GNDREF
177 VDDSAFE
178 CD_MD
179 DVD_MD
180 CD_LD
181 DVD_LD
182 FOCUS_PWM
183 VDDPWM
184 TRACK_PWM
185 GNDPWM
186 SPDL_PWM
187, 188 STB, STA
189 NC
190 VDDC
191 GNDC
192 SEN
193 REQ
194 DUPTD2 for MASTER
DUPRD2 for
195
MASTER
TP0 for DEBUG,
196, 197
TP1 for DEBUG
198 to MEMDAT10 to
200 MEMDAT12
201 MEMADD0
202 MEMCS0#
203 MEMRD#
MEMDAT0,
204 to MEMDAT8,
207 MEMDAT1,
MEMDAT9
208 VDDC
62
I/O
O Analog YUV video signal (Y) output to the panel section
- Power supply terminal (+3.3V)
O Analog composite video signal (CVBS) output to the video processor and REAR OUT jack
O Analog YUV video signal (V) output to the panel section
- Power supply terminal (+3.3V)
O Analog YUV video signal (U) output to the panel section
I Gain adjust signal input terminal
- Ground terminal
I RF signal (positive) input from the optical pick-up block
I RF signal (negative) input from the optical pick-up block
- Power supply terminal (+3.3V)
I A signal input from the optical pick-up block
I B signal input from the optical pick-up block
- Power supply terminal (+3.3V)
I C signal input from the optical pick-up block
I D signal input from the optical pick-up block
I J signal input terminal
I E signal input from the optical pick-up block
I K signal input terminal
I F signal input from the optical pick-up block
- Ground terminal
I G signal input terminal
I H signal input terminal
- Ground terminal
O Reference voltage (+1.65V) output to the optical pick-up block
- External capacitor connection terminal for internal band-gap voltage generation
- External resistor connection terminal for internal reference voltage generation
- Ground terminal
- Power supply terminal (+3.3V)
I Light amount monitor input from the laser diode of optical pick-up block (for CD)
I Light amount monitor input from the laser diode of optical pick-up block (for DVD)
O Laser diode on/of control signal output terminal (for CD)
O Laser diode on/of control signal output terminal (for DVD)
O Focus coil drive signal output terminal
- Power supply terminal (+3.3V)
O Tracking coil drive signal output terminal
- Ground terminal
O Spindle motor drive signal output terminal
O Sled motor drive signal output terminal
- Not used
- Power supply terminal (+1.8V)
- Ground terminal
I Clear to send signal input from the master controller
O Request to send signal output to the master controller
O Serial data output to the master controller
I Serial data input from the master controller
- Not used
I/O Two-way data bus with the fl ash memory
O Address signal output to the fl ash memory
O Chip select signal output terminal
O Read enable signal output to the fl ash memory
I/O Two-way data bus with the fl ash memory
- Power supply terminal (+1.8V)
Description
Not used
Not used
Not used
Not used
Not used
Not used
"H": laser diode on
"H": laser diode on