Rohde & Schwarz Hameg HMO3522 Manual
  1. Manuals
  2. Brands
  3. Rohde & Schwarz Manuals
  4. Test Equipment
  5. Hameg HMO3522
  6. Manual
Rohde & Schwarz Hameg HMO3522 Manual

Rohde & Schwarz Hameg HMO3522 Manual

Digital oscilloscope
Hide thumbs Also See for Hameg HMO3522:
Table of Contents

Advertisement

Quick Links

Download this manual
3 5 0 M H z
D i g i t a l O s c i l l o s c o p e
with FFT and mixed-signal (option)
H M O 3 5 2 2 / 3 5 2 4
Manual
English

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Hameg HMO3522 and is the answer not in the manual?

Questions and answers

Related Manuals for Rohde & Schwarz Hameg HMO3522

Summary of Contents for Rohde & Schwarz Hameg HMO3522

  • Page 1 3 5 0 M H z D i g i t a l O s c i l l o s c o p e with FFT and mixed-signal (option) H M O 3 5 2 2 / 3 5 2 4 Manual English...
  • Page 2 G e n e r a l i n f o r m a t i o n r e g a r d i n g t h e C E m a r k i n g General information regarding the CE marking HAMEG instruments fulfi...
  • Page 3 C o n t e n t s General information regarding the CE marking Display of signals 7.1. Display settings 350 MHz Digital Oscilloscope HMO3522 / HMO3524 7.2. Use of the virtual screen area 7.3. Signal intensity and persistence functions Specifi...
  • Page 4 H M O 3 5 2 4 3 5 0 M H z 2 / 4 C h a n n e l D i g i t a l O s c i l l o s c o p e H M O 3 5 2 2 / H M O 3 5 2 4 8 Channel logic probe HO3508...
  • Page 5 T e c h n i s c h e D a t e n Min. signal height 0.8div; 0.5div typ. 350 MHz 2 [4] Channel Digital Oscilloscope Frequency range 0…400MHz Level control range –10div..+10div. HMO3522 [HMO3524] Operating modes: All data valid at 23 °C after 30 minute warm-up after time 20ns…0.1s after incidence...
  • Page 6 I n s t a l l a t i o n a n d s a f e t y i n s t r u c t i o n s 1.2. Safety 1 Installation and safety instructions The instrument fulfi...

  • Page 7: Maintenance

    I n s t a l l a t i o n a n d s a f e t y i n s t r u c t i o n s in all operating modes; the test gear is calibrated to national The holder with the new fuse can then be pushed back in place standards.

  • Page 8: Front View

    I n t r o d u c t i o n HMO 3524 HMO 3524 CURSOR/MENU ANALYZE GENERAL 350 MHz / 4 GSa / 2 MB DIGITAL OSCILLOSCOPE 350 MHz / 4 GSa / 2 MB DIGITAL OSCILLOSCOPE CURSOR CURSOR SAVE AUTO...

  • Page 9: Rear View

    I n t r o d u c t i o n the optional logic probes 24 25 . There are also the mathematics contains the most important settings of the channel actually function key and the reference signal settings key being displayed;...
  • Page 10 I n t r o d u c t i o n 2.7. Basic setting and integrated help – Such keys which open a soft menu upon the fi rst touch will close it upon pushing a second time. Basic settings like language for user interface and help, mis- cellaneous settings and interface settings can be set using –...
  • Page 11 I n t r o d u c t i o n on the key (including softmenu key’s) you are pushing or the If you intend to update the help function or add a help language knob you are turning. If you do not need the help anymore, you choose HELP in the updating menu.

  • Page 12: Setting Up And Turning The Instrument On

    A q u i c k i n t r o d u c t i o n On the right hand side of the screen you will see a short menu of 3 A quick introduction channel 1, the soft keys allow you to select frequently used settings. Press the top soft key once to change the input coupling to DC.

  • Page 13: Automatic Measurements

    A q u i c k i n t r o d u c t i o n You see now a two-window display: the display will show in cursors will be switched off by pressing the CURSOR/MEASURE the top area the complete captured signal, below an enlarged key and the associated CURSORS OFF soft key.

  • Page 14: Storing Data

    A q u i c k i n t r o d u c t i o n The two parameters are displayed in the right bottom corner of the screen. You may defi ne the parameter measurement using this menu. After switching on MEASURE 1 and MEASURE 2 with the appropriate softkey’s the parameter measurements are displayed in the right bottom corner of the screen.
  • Page 15 V e r t i c a l s y s t e m 4 Vertical system CHANNEL CONTROL For the vertical settings there are Y-POSITION the knobs for the vertical position and the sensitivity, an always vi- sible short menu and an extended menu.

  • Page 16: Sensitivity, Y-Positioning, And Offset

    V e r t i c a l s y s t e m The passive probes must be adjusted to the inputs higher frequency interference. The fi lter is activated in the to which they are connected. See the probe manual short menu by pushing the respective soft key;...
  • Page 17 H o r i z o n t a l S y s t e m ( T i m e B a s e ) – Average: 5 Horizontal System (Time Base) Functions only with repetitive signals. The universal knob in the CURSOR/MENU section of the front panel is used to set the number of signal periods for averaging, this is possible As well as time base settings, the...

  • Page 18: Trigger Modes Auto, Normal, Single

    H o r i z o n t a l S y s t e m ( T i m e B a s e ) the knob is pushed, the time base display will change to white, 6 Trigger System and the zoom time base display to grey: now the knob is available for changing the time base setting.

  • Page 19: Trigger Sources

    T r i g g e r S y s t e m ditions only once, the key SINGLE must be pushed, it will light The slope trigger can be coupled with a so called „B Trigger“. up white. This indicates that the single trigger mode is active, This option is available after pushing TYPE.
  • Page 20 D i s p l a y o f s i g n a l s 6.5. Video trigger 7 Display of signals The video trigger allows you to trigger on PAL or NTSC standard video signals. Select this mode by pushing the key TYPE in the trigger control section of the front panel.

  • Page 21: Signal Intensity And Persistence Functions

    D i s p l a y o f s i g n a l s al range of 20 divisions. These may be used by the 16 digital be changed with the universal knob. The soft menu key next channels D0 to D15, the math functions and the references.
  • Page 22 D i s p l a y o f s i g n a l s displays the frequency and phase relationships of the signals 8 Measurements may be derived. The XY function will be activated by pushing the XY key in the CHANNEL CONTROL section of the front panel; the key will light up, and the screen will be partitioned in a large and some small display fi...
  • Page 23 M e a s u r e m e n t s RATIO Y This mode provides 3 cursors in order to measure ratios in Y direction (e.g. an overshoot) between the fi rst and the second and between the fi rst and the third cursors. The results will be presented in 2 formats: fl...
  • Page 24 M e a s u r e m e n t s PEAK-TO-PEAK 9 Analysis In this mode the voltage difference between the minimum and maximum values of the displayed signal will be measured. PEAK + The HMO352x series oscilloscopes feature a variety of analysis In this mode the positive peak value of the displayed signal will functions for the stored data sets which will be displayed on the be measured.
  • Page 25 A n a l y s i s The upper 3 menu keys allow you to select the sources as well as the operation. All active channels are available as sources. The available operations are addition and subtraction. 9.2. Formula editor The HMO352x series offers 5 sets of mathematical formulas.

  • Page 26: Frequency Analysis (Fft)

    A n a l y s i s constants and names it is possible to also add a name for this set of formulas by pushing the key next to NAME in the set of formulas menu and following the above procedure again. The completed set of formulas may be stored in the instrument or on a USB stick.

  • Page 27: Instrument Settings

    D o c u m e n t a t i o n , s t o r i n g a n d r e c a l l i n g Here the storage location (internal memory, front panel USB, 10 Documentation, storing and recalling rear panel USB) is selected, also a name and a commentary can be added;...
  • Page 28 D o c u m e n t a t i o n , s t o r i n g a n d r e c a l l i n g 10.2. References The following formats are available: References are sets of data which consist of settings informa- tion and A/D converter data.

  • Page 29: Sets Of Formulas

    D o c u m e n t a t i o n , s t o r i n g a n d r e c a l l i n g 10.4. Screen shots The most important method of storing for documentation purposes is the screen photo.

  • Page 30: Logic Trigger

    M i x e d S i g n a l O p e r a t i o n After selecting the desired set of conditions, you may push 11 Mixed Signal Operation (optional) FILTER for more settings. A soft menu will have opened which allows you to limit the trigger TRUE condition further in time (in this menu that condition will appear which you choose in the All HMO352x series instruments are provided with the con-...
  • Page 31 M i x e d S i g n a l O p e r a t i o n Fig. 11.2: Logic channels’ settings display The Y positions and the size of the logic channel displays can be chosen as customary and known from analog channel operation with the appropriate knobs Y-POSITION and SCALE VOLTS/DIV (provided the soft menu key „0/7“...
  • Page 32 A p p e n d i x Fig. 7.1: Drawing of the virtual screen area 12 Appendix and an example Fig. 7.2: Menu for setting the signal display intensities Fig. 7.3: Persistence function List of fi gures Fig. 7.4: Settings in the X–Y menu Fig.
  • Page 33 A p p e n d i x Subject to change without notice...
  • Page 34 A p p e n d i x Subject to change without notice...
  • Page 35 A p p e n d i x Subject to change without notice...
  • Page 36 Oscilloscopes Spectrum Analyzer Power Supplies Modular System Series 8000 Programmable Instruments Series 8100 authorized dealer w w w . h a m e g . c o m Subject to change without notice HAMEG Instruments GmbH 41-352X-00E0 (2) 23042009 Industriestraße 6 ©...

This manual is also suitable for:

Hameg hmo3524

Table of Contents